ETSI EN 301 681-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Mobile Earth Stations (MES) of Geostationary mobile satellite systems including handheld ear.pdf

《ETSI EN 301 681-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Mobile Earth Stations (MES) of Geostationary mobile satellite systems including handheld ear.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 681-2016 Satellite Earth Stations and Systems (SES) Harmonised Standard for Mobile Earth Stations (MES) of Geostationary mobile satellite systems including handheld ear.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 681 V2.1.2 (2016-11) Satellite Earth Stations and Systems (SES); Harmonised Standard for Mobile Earth Stations (MES) of Geostationary mobile satellite systems, including handheld earth stations, for Satellite Personal Communications Networks (S-PCN) under the Mobile Satellite Service (M

2、SS), operating in the 1,5 GHz and 1,6 GHz frequency bands covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 681 V2.1.2 (2016-11) 2 Reference REN/SES-00390 Keywords earth station, MES, mobile, MSS, radio, satellite, S-PCN ETSI

3、 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/

4、www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived dif

5、ference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or c

6、hange of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSuppor

7、tStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorizat

8、ion of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are

9、Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 681 V2.1.2 (2016-11) 3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminol

10、ogy 6g3Introduction 7g31 Scope 8g32 References 8g32.1 Normative references . 8g32.2 Informative references 9g33 Definitions and abbreviations . 9g33.1 Definitions 9g33.2 Abbreviations . 11g34 Technical requirement specifications . 12g34.1 Environment profile . 12g34.2 Conformance requirements 12g34.

11、2.1 Unwanted emissions outside the band 1 626,5 MHz to 1 660,5 MHz and outside the band 1 668,0 MHz to 1 675,0 MHz (carrier-on state) . 12g34.2.1.1 Justification . 12g34.2.1.2 Technical requirements . 12g34.2.1.3 Conformance test 15g34.2.2 Unwanted emissions within the bands 1 626,5 MHz to 1 660,5 M

12、Hz and 1 660,5 MHz to 1 662,5 MHz and within the bands 1 666,0 MHz to 1 668,0 MHz, 1 668,0 MHz to 1 675,0 MHz and 1 675,0 MHz to 1 677,0 MHz (carrier-on state) . 15g34.2.2.1 Justification . 15g34.2.2.2 Technical requirements . 16g34.2.2.3 Conformance test 17g34.2.3 Unwanted emissions in carrier-off

13、state 17g34.2.3.1 Justification . 17g34.2.3.2 Technical requirements . 18g34.2.3.3 Conformance test 18g34.2.4 MES Control and Monitoring Functions (CMF) 18g34.2.4.1 Self-monitoring functions/Processor monitoring 18g34.2.4.1.1 Justification . 18g34.2.4.1.2 Technical requirements 18g34.2.4.1.3 Conform

14、ance test . 18g34.2.4.2 Self-monitoring functions/Transmit frequency generation sub-system monitoring 19g34.2.4.2.1 Justification . 19g34.2.4.2.2 Technical requirements 19g34.2.4.2.3 Conformance test . 19g34.2.4.3 Network control authorization 19g34.2.4.3.1 Justification . 19g34.2.4.3.2 Technical re

15、quirements 19g34.2.4.3.3 Conformance test . 19g34.2.4.4 Network control reception . 19g34.2.4.4.1 Transmission disable/enable 19g34.2.4.4.2 Transmit frequency control . 20g34.2.4.5 Fellow radio stations in a dual-mode or multimode terminal 20g34.2.4.5.1 Justification . 20g34.2.4.5.2 Technical requir

16、ements 20g34.2.4.5.3 Conformance test . 20g34.2.5 Equipment identity 21g34.2.5.1 Justification . 21g34.2.5.2 Technical requirements . 21g34.2.5.3 Conformance test 21g3ETSI ETSI EN 301 681 V2.1.2 (2016-11) 4 4.2.6 Protection of the radio astronomy service operation in the band 1 660 MHz to 1 660,5 MH

17、z and in the band 1 668,0 MHz to 1 670,0 MHz 21g34.2.6.1 Purpose 21g34.2.6.2 Technical requirements . 21g34.2.6.3 Conformance test 21g34.2.7 Receiver Adjacent Channel Selectivity. 21g34.2.7.1 Purpose 21g34.2.7.2 Technical requirements . 21g34.2.7.3 Conformance test 22g34.2.8 Receiver Blocking Charac

18、teristics 22g34.2.8.1 Purpose 22g34.2.8.2 Technical requirements . 22g34.2.8.3 Conformance test 22g35 Testing for compliance with technical requirements 22g35.1 Environmental conditions for testing . 22g35.2 Radio test suites 23g35.2.1 General 23g35.2.1.1 Description of equipment 23g35.2.1.2 Testing

19、 of host-connected equipment and plug-in modules 24g35.2.1.2.1 Alternative approaches 24g35.2.1.2.2 Alternative A: combined equipment 24g35.2.1.2.3 Alternative B: use of a test jig . 24g35.2.1.3 CMF/Special Test Equipment (STE) 24g35.2.1.4 General test requirements 24g35.2.1.4.1 MES test modes . 24g

20、35.2.1.4.2 Special Test Equipment (STE) 25g35.2.1.4.3 Laboratory Test Equipment (LTE) 26g35.2.1.4.4 Methods of test for MES RF emissions according to the equipment type . 26g35.2.1.4.5 Procedures for measurement of radiated emissions . 26g35.2.1.4.6 Procedures for measurement of conducted emissions

21、. 31g35.2.1.4.7 Interpretation of the measurement results 33g35.2.1.4.8 Test report 33g35.2.2 Unwanted emissions outside the band 1 626,5 MHz to 1 660,5 MHz and outside the band 1 668,0 MHz to 1 675,0 MHz (carrier-on state) . 33g35.2.2.1 Method of test . 33g35.2.2.2 Peak measurement . 34g35.2.2.3 Av

22、erage measurement. 34g35.2.2.4 Test requirements 35g35.2.3 Unwanted emissions within the band 1 626,5 MHz to 1 660,5 MHz and the band 1 624,5 MHz to 1 626,5 MHz and 1 660,5 MHz to 1 662,5 MHz and within the band 1 668,0 MHz to 1 675,0 MHz and the band 1 666,0 MHz to 1 668,0 MHz and 1 675,0 MHz to 1

23、677,0 MHz (carrier-on state) . 35g35.2.3.1 Method of test . 35g35.2.3.2 Measurement method 35g35.2.3.3 Test requirements 36g35.2.4 Unwanted emissions in carrier-off state 36g35.2.4.1 Method of test . 36g35.2.4.2 Measurement method 36g35.2.4.3 Test requirements 37g35.2.5 MES Control and Monitoring Fu

24、nctions (CMF) 37g35.2.5.1 Self-monitoring functions/Processor monitoring 37g35.2.5.2 Self-monitoring functions/Transmit frequency generation sub-system monitoring 37g35.2.5.3 Network control authorization 37g35.2.5.3.1 Method of test 37g35.2.5.3.2 Test procedure . 37g35.2.5.3.3 Test requirements 38g

25、35.2.5.4 Network control reception . 38g35.2.5.4.1 Transmission disable/enable 38g35.2.5.4.2 Transmit frequency control . 39g35.2.5.5 Fellow radio stations in a dual-mode or multimode terminal 40g35.2.5.5.1 Method of test 40g35.2.5.5.2 Test procedure . 40g3ETSI ETSI EN 301 681 V2.1.2 (2016-11) 5 5.2

26、.5.5.3 Test requirements 40g35.2.6 Equipment identity 40g35.2.6.1 Method of test . 40g35.2.6.2 Test procedure . 40g35.2.6.3 Test requirements 40g35.2.7 Receiver Adjacent Channel Selectivity. 41g35.2.7.1 General 41g35.2.7.2 Test arrangement . 41g35.2.7.3 Test Procedures. 41g35.2.8 Receiver Blocking C

27、haracteristics 41g35.2.8.1 General 41g35.2.8.2 Test arrangement . 42g35.2.8.3 Test procedures . 42g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 43g3Annex B (informative): Bibliography . 45g3History 46g3ETSI ETSI EN 301 681 V

28、2.1.2 (2016-11) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Int

29、ellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, inc

30、luding IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard

31、(EN) has been produced by ETSI Technical Committee Satellite Earth Stations and Systems (SES). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.3 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/E

32、U on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.5. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clause

33、s of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 12 Sep

34、tember 2016 Date of latest announcement of this EN (doa): 31 December 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 June 2018 Modal verbs terminology In the present document “

35、shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when u

36、sed in direct citation. ETSI ETSI EN 301 681 V2.1.2 (2016-11) 7 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio equipment within the scope of the RE Directive i.5. The modular structure is shown in ETS

37、I EG 201 399 i.1. The determination of the parameters of the user earth stations using a given satellite for the protection of the spectrum allocated to that satellite, is considered to be under the responsibility of the satellite operator or the satellite network operators. Following the WRC-03 dec

38、ision i.4 to allocate to MSS the bands 1 518 MHz to 1 525 MHz (space to Earth) and 1 668 MHz to 1 675 MHz (Earth to space) and the conclusions of WRC-07, a new set of emission requirements for LMESs that are capable of transmitting in the frequency band from 1 668,0 MHz to 1 675,0 MHz were specified

39、. The two parts of the L-band frequency allocations are treated as two sub-bands which may be used separately or in any combination. The original L-band allocation is referenced in the present document as “sub-band 1“ and the extended L-band is referenced as “sub-band 2“. Table 3a is applicable for

40、MESs that are capable of transmitting in any combination of either or both of these sub-bands. Table 3a is recommended for all new MESs, including MESs that can only operate in sub-band 1. The applicant may choose between table 3 and table 3a for new MESs that are capable of transmitting in only the

41、 sub-band 1: the applicant has to declare which alternative is used. The present document specifies a new set of receiver performance requirements for LMESs under the new Radio Equipment Directive 2014/53/EU i.5. Figure 1: Void Recital 10 of Directive 2014/53/EU i.5 states that “In order to ensure t

42、hat radio equipment uses the radio spectrum effectively and supports the efficient use of radio spectrum, radio equipment should be constructed so that: in the case of a transmitter, when the transmitter is properly installed, maintained and used for its intended purpose it generates radio waves emi

43、ssions that do not create harmful interference, while unwanted radio waves emissions generated by the transmitter (e.g. in adjacent channels) with a potential negative impact on the goals of radio spectrum policy should be limited to such a level that, according to the state of the art, harmful inte

44、rference is avoided; and, in the case of a receiver, it has a level of performance that allows it to operate as intended and protects it against the risk of harmful interference, in particular from shared or adjacent channels, and, in so doing, supports improvements in the efficient use of shared or

45、 adjacent channels.“ Recital 11 of Directive 2014/53/EU i.5 states that “Although receivers do not themselves cause harmful interference, reception capabilities are an increasingly important factor in ensuring the efficient use of radio spectrum by way of an increased resilience of receivers against

46、 harmful interference and unwanted signals on the basis of the relevant essential requirements of Union harmonisation legislation.“ ETSI ETSI EN 301 681 V2.1.2 (2016-11) 8 1 Scope The present document applies to S-PCN MES for Geostationary mobile satellite systems with an EIRP less than or equal to

47、15 dBW. The present document sets out the minimum performance requirements and technical characteristics of Mobile Earth Stations (MES) with both transmit and receive capabilities for operation in a Satellite Personal Communication Network (S-PCN) in any combination of all or any part of the Mobile

48、Satellite Service (MSS) frequency bands sub-band 1 and sub-band 2 defined in table 1. These MESs are controlled and monitored by a Network Control Facility (NCF). The NCF is outside the scope of the present document. Table 1: Mobile Satellite Service (MSS) frequency band Sub-band Transmission path M

49、SS frequency band 1 MESs transmit 1 1 626,5 MHz to 1 660,5 MHz MESs receive 1 1 525 MHz to 1 559 MHz 2 MESs transmit 2 1 668,0 MHz to 1 675,0 MHz MESs receive 2 1 518,0 MHz to 1 525,0 MHz An S-PCN MES may be handheld, portable, vehicle-mounted, host connected, semi-fixed or fixed equipment, or may be an element in a multimode terminal; it may consist of a number of modules with associated connections and user interface, or may be a self-contained single unit. If the MES is an element in a multimode terminal, unless otherwise stated in the present document, its