ETSI EN 301 489-23-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 23 Specifi_1.pdf

《ETSI EN 301 489-23-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 23 Specifi_1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 489-23-2011 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 23 Specifi_1.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 489-23 V1.5.1 (2011-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 23: Specific conditions for IMT-2000 CDMA, Direct Spread (UTRA and E-UTRA) Base Station (BS) radio, repeater and an

2、cillary equipment Harmonized European Standard ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)2Reference REN/ERM-EMC-277 Keywords base station, EMC, IMT-2000, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 3

3、48 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in p

4、rint. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat.

5、Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your c

6、omment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards

7、 Institute 2011. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Tra

8、de Marks registered and owned by the GSM Association. ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)3Contents Intellectual Property Rights 5g3Foreword . 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abb

9、reviations . 8g34 Test conditions . 9g34.1 General . 9g34.2 Arrangements for test signals . 9g34.2.1 Multiple enclosure BS solution . 10g34.2.2 Arrangements for test signals at the input of transmitters . 10g34.2.3 Arrangements for test signals at the output of transmitters . 10g34.2.4 Arrangements

10、for test signals at the input of receivers . 10g34.2.5 Arrangements for test signals at the output of receivers . 10g34.2.6 Arrangements for test signals for repeaters . 10g34.3 Exclusion bands 10g34.3.1 Receiver exclusion band . 10g34.4 Narrow band responses of receivers . 11g34.5 Normal test modul

11、ation 12g35 Performance assessment . 13g35.1 General . 13g35.2 Equipment which can provide a continuous communication link 13g35.2.1 Assessment of BLER/Throughput in Downlink . 13g35.2.2 Assessment of BLER/Throughput in Uplink 13g35.2.3 Assessment of RF gain variations of repeaters . 13g35.3 Equipme

12、nt which does not provide a continuous communication link 13g35.4 Ancillary equipment . 13g35.5 Equipment classification 14g36 Performance criteria . 14g36.1 Performance criteria for continuous phenomena applied to Base Stations and Repeaters . 14g36.1.1 Base Stations (BS) 14g36.1.2 Repeaters 15g36.

13、2 Performance criteria for transient phenomena for Base Station and Repeaters 15g36.2.1 Base stations (BS) . 15g36.2.2 Repeaters 16g36.2.2.1 Repeaters, Performance criteria for voltage dips ( 60 %) and interruptions . 16g36.3 Performance criteria for ancillary equipment tested on a standalone basis

14、16g36.3.1 Performance criteria for continuous phenomena for ancillary equipment 17g36.3.2 Performance criteria for transient phenomena for ancillary equipment 17g37 Applicability overview tables . 17g37.1 Emission . 17g37.1.1 General 17g37.1.2 Special conditions . 17g37.2 Immunity 17g37.2.1 General

15、17g37.2.2 Special conditions . 18g3ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)4Annex A (informative): Examples of base station radio equipment for digital cellular radio telecommunications systems within the scope of the present document 19g3A.1 Base station equipment for IMT-2000 CDMA Direct Spread (U

16、TRA) . 19g3A.2 Base station equipment for Evolved Universal Terrestrial Radio Access(E-UTRA) . 19g3Annex B (informative): The EN title in the official languages . 20g3History 21g3ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)5Intellectual Property Rights IPRs essential or potentially essential to the pres

17、ent document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in re

18、spect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of

19、other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum

20、Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Directive 98/34/EC i.7 as amended by Directive 98/48/EC i.8. The title and reference to the present document are intended to be included in the publication in the Official

21、 Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC i.6. See article 5.1 of Directive 1999/5/EC i.6 for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Offic

22、ial Journal of the European Union. The present document is part 23 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 10 November 2011 Date of latest announcement of this EN (doa): 29 February 2012 Date o

23、f latest publication of new National Standard or endorsement of this EN (dop/e): 31 August 2012 Date of withdrawal of any conflicting National Standard (dow): 31 August 2013 ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)61 Scope The present document, together with EN 301 489-1 1, covers the assessment of

24、“3rdgeneration“ digital cellular (IMT-2000 CDMA Direct Spread) (UTRA and E-UTRA) base station equipment, repeaters and associated ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of radio

25、 equipment (base station (BS), and repeaters) are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment and per

26、formance criteria of “3rdgeneration“ digital cellular (IMT-2000 CDMA Direct Spread) (UTRA and E-UTRA) base station radio equipment and associated ancillary equipment. Examples of base station equipment covered by the present document are given in annex A. In case of differences (for instance concern

27、ing special conditions, definitions, abbreviations) between the present document and EN 301 489-1 1, the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in EN 301 489-1 1, excep

28、t for any special conditions included in the present document. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest ver

29、sion of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ET

30、SI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 489-1 (V1.8.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) stan

31、dard for radio equipment and services; Part 1: Common technical requirements“. 2 ETSI TS 125 141 (V7.5.0): “Universal Mobile Telecommunications System (UMTS); Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 7.5.0 Release 7)“. 3 ETSI TS 125 142 (V7.3.0): “Universal Mobile Telecomm

32、unications System (UMTS); Base Station (BS) conformance testing (TDD) (3GPP TS 25.142 version 7.3.0 Release 7)“. 4 ETSI TS 125 101 (V7.5.0): “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.101 version 7.5.0 Release 7)“. 5 ETS

33、I TS 125 102 (V7.4.0): “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (TDD) (3GPP TS 25.102 version 7.4.0 Release 7)“. 6 ETSI TS 125 143 (V7.2.0): “Universal Mobile Telecommunications System (UMTS); UTRA repeater conformance testing (3GPP TS

34、25.143 version 7.2.0 Release 7)“. ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)77 ETSI TS 136 101: “LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) radio transmission and reception (3GPP TS 36.101 version 9.3.0 Release 9)“. 8 ETSI TS 136 104 (V9.3.0): “LTE; Evolved Universal

35、 Terrestrial Radio Access (E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 9.3.0 Release 9)“. 9 ETSI TS 136 141 (V9.3.0): “LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 9.3.0 Release 9)“. 2.

36、2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 136 106: “LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater radio transmission

37、 and reception (3GPP TS 36.106)“. i.2 ETSI TS 136 143: “LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater conformance testing (3GPP TS 36.143)“. i.3 ETSI TS 125 104: “Universal Mobile Telecommunications System (UMTS); Base Station (BS) radio transmission and reception (FDD) (3GP

38、P TS 25.104)“. i.4 ETSI TS 125 105: “Universal Mobile Telecommunications System (UMTS); Base Station (BS) radio transmission and reception (TDD) (3GPP TS 25.105)“. i.5 ETSI TS 125 106: “Universal Mobile Telecommunications System (UMTS); UTRA repeater radio transmission and reception (3GPP TS 25.106)

39、“. i.6 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R UTRA (TDD) base station TS 125 142 3; E-UTRA base station TS 136 141 9; UTRA repeater conformance te

40、sting specification TS 125 143 6; E-UTRA repeater conformance testing specification TS 136 143 i.2. The test conditions shall be recorded in the test report. For emission and immunity tests the test arrangements, etc., as specified in the present document, clauses 4.2 to 4.5, shall apply. For an EUT

41、 which contains more than one BS, it is sufficient to perform tests relating to connectors of each representative type of port forming part of the EUT. 4.2 Arrangements for test signals The provisions of EN 301 489-1 1, clause 4.2 shall apply, with the following modifications. UTRA the wanted RF sig

42、nal nominal frequency shall be selected by setting the UTRA Absolute Radio Frequency Channel Number (UARFCN). E-UTRA the wanted RF signal nominal frequency shall be selected by setting the E-UTRA Absolute Radio Frequency Channel Number (EARFCN) to an appropriate number. UTRA a communication link sha

43、ll be set up with a suitable test system capable of evaluating the EUT using the specified performance criteria at the air interface and/or the Iub interface. E-UTRA a communication link shall be set up with a suitable test system capable of evaluating the EUT using the specified performance criteri

44、a at the air interface and/or the SI interface. For both UTRA and E-UTRA the test system shall be located outside of the test environment. When the EUT is required to be in the transmit/receive mode, the following conditions shall be met: the EUT shall be commanded to operate at maximum rated transm

45、it power; adequate measures shall be taken to avoid the effect of the unwanted signal on the measuring equipment. ETSI ETSI EN 301 489-23 V1.5.1 (2011-11)104.2.1 Multiple enclosure BS solution For a BS with multiple enclosures, the BS part with Radio digital unit and the Radio unit may be tested sep

46、arately. Communication link shall be set up in the same way as if they are in single BS enclosure. The Radio Digital unit and the Radio unit shall communicate over an interface enabling establishment of a communication link. 4.2.2 Arrangements for test signals at the input of transmitters The provis

47、ions of EN 301 489-1 1, clause 4.2.1 shall apply. 4.2.3 Arrangements for test signals at the output of transmitters The provisions of EN 301 489-1 1, clause 4.2.2 shall apply. 4.2.4 Arrangements for test signals at the input of receivers The provisions of EN 301 489-1 1, clause 4.2.3 shall apply wit

48、h the following modification. The wanted input signal level shall be set to a level to provide a stable communication link where the performance is not limited by the receiver noise floor or strong signal effects e.g. 15 dB above the reference sensitivity level as defined in: - UTRA TS 125 141 2 (fo

49、r FDD), TS 125 142 3 (for TDD); - E-UTRA TS 136 141 9. 4.2.5 Arrangements for test signals at the output of receivers The provisions of EN 301 489-1 1, clause 4.2.4 shall apply. 4.2.6 Arrangements for test signals for repeaters For immunity tests of repeaters, the wanted RF input signal shall be coupled to one antenna port at a level which will result, when measured, in the maximum rated RF output power per channel, as declared by the manufacturer. The test shall either be repeated with a wanted