ETSI EN 301 489-14-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 14 Specifi.pdf

《ETSI EN 301 489-14-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 14 Specifi.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 489-14-2003 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 14 Specifi.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI EN 30 1 489-1 4 VI 2.1 (2003-05) Candida fe Harmonized European Sfandard (Telecommunicafions series) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 14: Specific conditions for analogue and digit

2、al terrestrial TV broadcasting service transmitters 2 ETSI EN 301 489-14 VI .2.1 (2003-05) Reference REN/ERM-EMC-23O-I 4 Keywords broadcasting, digital, EMC, radio, regulation, testing, TV ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47

3、 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:lwmv.etsi .arq The present document may be made available in more than one electronic

4、 version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ET

5、SI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors in the present doc

6、ument, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTS

7、TMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partn

8、ers. ETSI 3 ETSI EN 301 489-14 VI .2.1 (2003-05) Contents Intellectual Property Rights . .4 Foreword . 4 1 2 3 3.1 3.2 4 4.1 4.2 4.2.1 4.2.2 4.2.3 4.3 4.3.1 4.3.2 4.3.3 4.4 4.5 4.5.1 4.5.2 5 5.1 5.2 5.3 5.4 5.5 6 6.1 6.2 7 7.1 7.1.1 7.1.2 7.2 7.2.1 7.2.2 Scope 5 References . .5 Definitions and abbre

9、viations. . .6 Definitions 6 Abbreviations . 6 Test conditions .7 test signals . 7 Arrangements for test signals at the input of transmitters. Arrangements for test signals at the input of transposers, active deflectors, or RF power amplifiers 7 power amplifiers . 8 9 Transmitter and RF power amplif

10、ier exclusion band 9 9 Transposer exclusion band. . 9 Narrow band responses of receivers . 10 10 Analogue Modulation . 10 Digital Modulation (T-DVB) 10 Performance assessment . 10 7 7 General Arrange Arrangements for test signals at the output of transmitters, transposers, active deflectors or RF RF

11、 exclusion bands Active deflector exclusion band. . Normal test modulation General . . us communication link as a broadcasting transmission . Equipment which does not provide a continuous communication link as a broadcasting transmission . Ancillary equipment . Equipment classifica . Performance cri

12、teria for Continuous phenomena applied to Transmitters (CT) 1 1 Performance criteria for Transient phenomena applied to Transmitters (TT) 12 Applicability overview .12 Performance criteria . 11 12 12 ons . 12 13 General 13 Special conditions . 13 . . . Annex A (informative): A. 1 Types of broadcasti

13、ng service equipment covered by the present document 15 Analogue television. .15 A.2 Digital television . .15 Annex B (informative): Annex C (informative): Bibliography . 16 The EN title in the official languages . 17 History . .18 ETSI 4 ETSI EN 301 489-14 VI .2.1 (2003-05) Intellectual Property Ri

14、ghts IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 3 14: “Intellectual Property Rights (7PRs); Essenti

15、al, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (5). All published ETSI deliverables shall include information which directs the reader to the above source of informatio

16、n. Foreword This Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issue

17、d under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document, together with EN 301 489-1 i, is intended to become a Harmonized Standard, the reference of which will be published in t

18、he Official Journal of the European Communities referencing the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (“the EMC Directive“) (89/336/EEC 2 as amended) and Directive 1999/5/EC 3 of the European Parliament and of the Council of

19、 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1 : Common technical requirements“. Council Directive 89/336/EEC of 3 May 1989 on the

20、approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive). Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R R

21、adio disturbance characteristics - Limits and methods of measurement“. 21 31 41 51 61 ETSI EN 300 744 (V1.4.1): “Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for digital terrestrial television“. ETSI 6 ETSI EN 301 489-14 VI .2.1 (2003-05) 71 EN 61000-4-3 1996/A1

22、 (1998): “Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test“. 3 3.1 Definitions and abbreviations Def i nit ions For the purposes of the present document, the ternis and definitions given in EN 301 489-

23、1 i and the following apply: active deflector: TdRx (transceiver, repeater, gap filler), which receives an input signal off-air, and re-broadcasts the same signal on the same frequency broadcasting service: radiocommunication service in which the transmissions are intended for direct reception by th

24、e general public NOTE: This service may include sound transmission, television transmission, or other types of transmission. exciter: low level RF power driver stage of a broadcasting transmitter RF power amplifier: Tx, which comprises an amplifier, declared by the manufacturer to be capable of bein

25、g connected to a terrestrial broadcasting antenna system transposer: TdRx (transceiver), which receives an input signal off-air, and re-broadcasts the same signal on a different frequency 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AC BER CISPR CT D

26、C DQPSK DVB EMC EUT IF IRT MER MPEG NICAM RF Rx SNR T-DVB TS TT TV Tx UHF VHF QAM rmS Alternating Current Bit Error Ratio International Special Committee on Radio Interference (in IEC) Continuous phenomena applied to Transmitters Direct Current Differential Quaternary Phase-Shift Keying Digital Vide

27、o Broadcasting ElectroMagnetic Compatibility Equipment Under Test Intermediate Frequency Institut fr RundfunkTechnik Modulation Error Ratio Moving Picture Experts Group Near-Instantaneous Companded Audio Multiplex Quadrature Amplitude Modulation Radio Frequency root mean square Receiver Signal to No

28、ise Ratio Terrestrial Digital Video Broadcasting Transport Stream Transient phenomena applied to Transmitters Television Transmitter Ultra High Frequency Very High Frequency ETSI 7 ETSI EN 301 489-14 VI .2.1 (2003-05) 4 Test conditions For the purposes of the present document, the test conditions of

29、 EN 301 489-1 i, clause 4 shall apply as appropriate. Further provisions related to test conditions for broadcasting service transmitters are specified in the present document. 4.1 Gen eral For emission and immunity tests the test modulation, test arrangements, etc. as specified in the present docum

30、ent, clauses 4.1 to 4.5 shall apply. For immunity tests, the output of the Tx shall be monitored as specified in the present document, clause 4.2.3. 4.2 Arrangements for test signals The provisions of EN 301 489-1 i, clause 4.2 shall apply. 4.2.1 Arrangements for test signals at the input of transmi

31、tters The provisions of EN 301 489-1 i, clause 4.2.1 shall apply, with the following modifications: If the transmitter under test incorporates base-band processing andor coding equipment (e.g. a NICAM encoder for an analogue modulated TV transmitter, or an MPEG2 encoder for a digital television tran

32、smitter), then this equipment shall be active as in normal operation. The manufacturer shall provide reference encoders and the tests shall be carried out with these in operational mode. If the transmitter under test does not include integrated base-band processing andor coding equipment, the manufa

33、cturer shall declare whether the transmitter is designed for operation with or without encoder(s). The manufacturer shall clearly state this in the product documentation. If the transmitter under test is designed for operation with externally fitted encoder(s), then it is lefi to the decision of the

34、 manufacturer whether the transmitter under test shall be tested with such encoder(s). Depending on the manufacturers decision, the manufacturer may have to provide reference encoders and the tests shall be carried out with these in operational mode. Any unused input port of the transmitter under te

35、st shall be terminated according to the manufacturers instructions. 4.2.2 Arrangements for test signals at the input of transposers, active deflectors, or RF power amplifiers The provisions of EN 301 489-1 i, clause 4.2.1 shall apply, with the following modifications: In case of transposers and acti

36、ve deflectors, the wanted RF input signal, at a frequency determined from the manufacturers specification, shall be set to a level equal to the mid point of the range declared by the manufacturer. In case of RF amplifiers, the wanted RF input signal of a suitable level shall be delivered from an ade

37、quate external modulator provided by the manufacturer. The modulator may be placed outside the test environment. A broadcasting transmission shall be established at the start of the test and maintained during the test. ETSI 8 ETSI EN 301 489-14 V1.2.1 (2003-05) 4.2.3 Arrangements for test signals at

38、 the output of transmitters, transposers, active deflectors or RF power amplifiers The provisions of EN 301 489-1 i, clause 4.2.2 shall apply with the following modifications. Typical test arrangements to assess the performance of the EUT are shown in: NOTE: figure 1 for analogue modulated TV transm

39、itters; figure 2 for T-DVB transmitters. In practice it is not necessary to use all the individual instrumentation shown in figure 1. For specific measurement requirements refer to table 1, Co up I i ng Test Device Load Generator I Video t+ Audio En coder NICAM - RF Video hut Tx UNDER I TEST I N ICA

40、MA RT Input Audio input Spectrum Analyser w Splitter Analogue TV Test Receiver Analyser Analyser Figure 1: Typical test arrangement for the performance assessment of a standard analogue modulated TV transmitter, example ETSI 9 ETSI EN 301 489-14 VI .2.1 (2003-05) Device RF output II II MPEG-2 Spectr

41、um Analyser w Splitter T-DVB Receiver v MPEG-2 Decoder and MER Monitor Figure 2: Typical test arrangement for the performance assessment of a T-DVB transmitter, example 4.3 RF exclusion bands The provisions of EN 301 489-1 i, clause 4.3 shall apply with the modifications set out in clauses 4.3.1,4.3

42、.2 and 4.3.3 of the present document. 4.3.1 Transmitter and RF power amplifier exclusion band The exclusion band for the transmitter andor power amplifier shall be the allocated channel. 4.3.2 Active deflector exclusion band The exclusion band for the active deflector (transmitting and receiving ele

43、ments) is equal to the channel centre frequency -5 % to +5 %. Special precautions shall be taken to avoid the wanted RF output of the active deflector from disturbing the signal at the RF input port. 4.3.3 Transposer exclusion band For emission measurements, the transposer exclusion band shall compr

44、ise the exclusion band of the transmitting element of the equipment under test only. For immunity tests with continuous phenomena, the transposer exclusion bands shall comprise both the exclusion bands of the transmitting and receiving elements of the equipment under test. The exclusion band for the

45、 transposer (transmitting and receiving elements) is equal to the channel centre frequency for each element -5 % to +5 %. For the receiver part of the transposer, the exclusion band takes into account the blocking effect that may occur due to the high level of the immunity test fieldstrength (10 V/m

46、) in regard to the RF input level of that receiver part (which is usually less than 1 mV). ETSI 10 ETSI EN 301 489-14 VI .2.1 (2003-05) 4.4 Narrow band responses of receivers The provisions of EN 301 489-1 i, clause 4.4 shall apply during the immunity tests of transposers and active deflectors to co

47、ntinuous phenomena. 4.5 Normal test modulation 4.5.1 Analogue Modulation The vision carrier shall be amplitude modulated with composite sync pulses and a 350 mV luminance bar, the sound 1 (mono) carrier shall be frequency modulated with a 1 kHz sinusoidal signal at a level to cause a frequency devia

48、tion of 50 kHz and the sound 2 (NICAM) carrier shall be DQPSK modulated with a pseudo random bit sequence. 4.5.2 Digital Modulation (T-DVB) The modulation signal at the input of the transmitter shall be as stated in EN 300 744 6, clause 4.3, but with the following specific settings: Mode 8K; Guard i

49、nterval duration 1/32; TS modulation 64 QAM; Code Ratio 213. 5 Performance assessment 5.1 Gen eral The provisions of EN 301 489-1 i, clause 5.1 shall apply. In addition, the manufacturer shall, at the time of submission of the equipment for testing, declare the following information, also to be recorded in the test report, as appropriate : the frequencies as used in the transmitter for oscillators, clocks and intermediate frequencies; the bandwidth of the IF filter, or the bandwidth of the RF filter if no IF signal processing is used; for RF ampl