ETSI EN 300 674-2-1-2016 Transport and Traffic Telematics (TTT) Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit s 250 kbit s) operating in the 5 795 MH_1.pdf

《ETSI EN 300 674-2-1-2016 Transport and Traffic Telematics (TTT) Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit s 250 kbit s) operating in the 5 795 MH_1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 674-2-1-2016 Transport and Traffic Telematics (TTT) Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit s 250 kbit s) operating in the 5 795 MH_1.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 300 674-2-1 V2.1.1 (2016-09) Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band; Part 2: Harmonised Standard covering the essential requirements of article

2、 3.2 of the Directive 2014/53/EU; Sub-part 1: Road Side Units (RSU) HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)2 Reference REN/ERM-TG37-26 Keywords data, DSRC, harmonised standard, radio, regulation, RTTT, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex

3、- FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may

4、be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in pri

5、nt, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of t

6、his and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be repro

7、duced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restrictio

8、n extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its M

9、embers and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g31 Scope 7g32 References 7g32.1 Normative refe

10、rences . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 9g33.1 Definitions 9g33.2 Symbols 10g33.3 Abbreviations . 12g34 Technical requirements specifications . 13g34.1 Mechanical and electrical design 13g34.1.1 Units 13g34.1.2 Controls 13g34.2 General characteristics . 1

11、3g34.2.1 RSU classes 13g34.2.2 Carrier frequencies 14g34.2.3 Modulation 14g34.2.4 Antenna characteristic . 14g34.3 Environmental conditions . 14g34.3.1 Environmental profile . 14g34.3.2 Power supply 14g34.4 Conformance requirements 15g34.4.1 Transmitter parameters . 15g34.4.1.1 General 15g34.4.1.2 M

12、aximum equivalent isotropically radiated power . 15g34.4.1.3 Transmitter frequency error 15g34.4.1.4 Transmitter spectrum mask . 15g34.4.1.5 Transmitter unwanted emissions . 16g34.4.2 Receiver parameters 16g34.4.2.1 Receiver spurious emissions . 16g34.4.2.2 Blocking 16g34.4.2.3 Sensitivity . 17g35 T

13、esting for compliance with technical requirements 17g35.1 Environmental conditions for testing . 17g35.2 Interpretation of the measurement results 17g35.3 Essential radio test suites 18g35.3.1 Transmitter parameters . 18g35.3.1.1 Maximum equivalent isotropically radiated power . 18g35.3.1.1.1 Genera

14、l 18g35.3.1.1.2 Radiated measurements . 18g35.3.1.1.3 Conducted measurements 19g35.3.1.2 Transmitter Frequency error 19g35.3.1.2.1 General 19g35.3.1.2.2 Radiated measurements . 19g35.3.1.2.3 Conducted measurements 20g35.3.1.3 Transmitter spectrum mask . 20g35.3.1.3.1 General 20g35.3.1.3.2 Radiated m

15、easurements . 21g35.3.1.3.3 Conducted measurements 22g35.3.1.4 Transmitter unwanted emissions . 23g35.3.1.4.1 General 23g35.3.1.4.2 Radiated measurements . 24g3ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)4 5.3.2 Receiver parameters 25g35.3.2.1 Receiver unwanted emissions in the spurious domain 25g35.3.

16、2.1.1 General 25g35.3.2.1.2 Radiated measurements . 25g35.3.2.2 Blocking 26g35.3.2.2.1 General 26g35.3.2.2.2 Radiated measurements . 26g35.3.2.3 Sensitivity . 27g35.3.2.3.1 General 27g35.3.2.3.2 Radiated measurements . 27g3Annex A (normative): Relationship between the present document and the essent

17、ial requirements of Directive 2014/53/EU . 29g3Annex B (normative): Basics on testing . 30g3B.1 General conditions 30g3B.1.1 Power source 30g3B.1.2 Thermal balance . 30g3B.1.3 Test signals . 30g3B.1.4 Test sites . 31g3B.1.4.1 Shielded anechoic chamber. 31g3B.1.4.2 Open area test site . 32g3B.1.4.3 T

18、est fixture 33g3B.1.5 General requirements for RF cables . 34g3B.1.6 Conducted measurements . 35g3B.1.6.1 One antenna connector arrangement . 35g3B.1.6.2 Two antenna connectors arrangement. 36g3B.1.6.3 Test site requirements . 36g3B.1.6.4 Site preparation for conducted measurements 36g3B.1.6.4.1 Mon

19、ochromatic signals . 36g3B.1.6.4.2 Modulated signals . 37g3B.1.7 Radiated measurements 37g3B.1.7.1 One antenna arrangement . 37g3B.1.7.2 Two antennas arrangement . 39g3B.1.7.3 Test site requirements . 40g3B.1.7.3.1 Measurement distances . 40g3B.1.7.3.2 Free-space wave propagation 40g3B.1.7.4 Test an

20、d substitution antennas 41g3B.1.7.5 Site preparation for RSU measurements . 41g3B.1.7.5.1 Arrangement for transmit parameters 41g3B.1.7.5.2 Arrangement for receive parameters . 42g3B.2 Instruments . 44g3B.2.1 Receiving device 44g3B.2.2 RF power sensor . 45g3B.2.3 Combiner 45g3B.3 Power of modulated

21、RSU carrier . 45g3B.4 Bit error ratio measurements 46g3B.4.1 Basics . 46g3B.4.2 BER measurement 47g3B.4.3 FER measurement 47g3B.4.3.1 Mathematical expressions . 47g3B.4.3.2 Equipment . 47g3B.4.3.3 Procedure 48g3Annex C (informative): Guidance on declaring the environmental profile 49g3C.1 Recommende

22、d environmental profile 49g3C.2 Normal environmental conditions 49g3C.3 Extreme environmental conditions . 49g3ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)5 Annex D (informative): Bibliography . 50g3Annex E (informative): Change History 51g3History 52g3ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)6 Intelle

23、ctual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights

24、 (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has

25、been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by

26、 ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.6 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on

27、the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.5. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of

28、the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document is part 2, sub-part 1 of a multi-part deliverable

29、 covering Transport and Traffic Telematics (TTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band, as identified below: Part 1: “General characteristics and test methods for Road Side Units (RSU) and O

30、n-Board Units (OBU)“; Part 2: “Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU“; Sub-part 1: “Road Side Units (RSU)“; Sub-part 2: “On-Board Units (OBU)“. National transposition dates Date of adoption of this EN: 12 September 2016 Date of latest announce

31、ment of this EN (doa): 31 December 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 June 2017 Date of withdrawal of any conflicting National Standard (dow): 30 June 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “sho

32、uld not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI E

33、N 300 674-2-1 V2.1.1 (2016-09)7 1 Scope The present document applies to Transport and Traffic Telematics (TTT) systems: with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna; for data transmission only; operating on radio frequencies in the 5,725 GHz to 5,87

34、5 GHz Short Range Devices frequency band. The applicability of the present document covers only the Road Side Units (RSU). The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable.

35、The present document complies with the Commission Implementing Decision 2013/752/EU 1 and CEPT/ERC Recommendation 70-03 2. It is a specific standard covering various TTT applications. The present document applies to the following radio equipment types operating in all or in part of the following ser

36、vice frequency bands given in table 1. Table 1: Frequency bands and centre frequencies fTxallocated for DSRC Pan European Service Frequencies National Service Frequencies Channel 1 5,795 GHz to 5,800 GHz, ftX= 5,7975 GHz Channel 2 5,800 GHz to 5,805 GHz, ftX= 5,8025 GHz Channel 3 5,805 GHz to 5,810

37、GHz, ftX= 5,8075 GHz Channel 4 5,810 GHz to 5,815 GHz, ftX= 5,8125 GHz The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references R

38、eferences are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Reference

39、d documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced docu

40、ments are necessary for the application of the present document. 1 Commission Implementing Decision 2013/752/EU of 11 December 2013 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2005/928/EC. 2 CEPT/ERC Recommendation 70-03

41、(2016): “Relating to the use of Short Range Devices (SRD)“. 3 CEN EN 12253:2004: “Road transport and traffic telematics - Dedicated short-range communication - Physical layer using microwave at 5,8 GHz“. ETSI ETSI EN 300 674-2-1 V2.1.1 (2016-09)8 4 ETSI TR 100 028 (V1.4.1) (12-2001) (all parts): “El

42、ectromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 5 IEC 60721-3-4:1995 including Amendment 1:1996: “Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and t

43、heir severities - Section 4: Stationary use at non-weatherprotected locations“. 6 IEC 60721-3-5:1997: “Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 5: Ground vehicle installations“. 7 CEN EN 12795:2003: “Road

44、 transport and traffic telematics - Dedicated Short Range Communication (DSRC) - DSRC data link layer: medium access and logical link control“. 8 CEN EN 12834:2003: “Road transport and traffic telematics - Dedicated Short Range Communication (DSRC) - DSRC application layer“. 9 ISO 14906 (2011): “Ele

45、ctronic fee collection - Application interface definition for dedicated short-range communication“. 10 CEPT/ERC Recommendation 74-01E (2011): “Unwanted emissions in the spurious domain“. 11 ETSI TR 102 273-2 (V1.2.1) (12-2001): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Improve

46、ment on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber“. 12 ETSI TR 102 273-6 (V1.2.1) (12-2001): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement

47、 (using test site) and evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures“. 13 CISPR 16-1 (2015): “Specification for radio disturbance and immunity measuring apparatus and methods - Part 1: Radio disturbance and immunity measuring apparatus“. 2.2 Informative references

48、References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: Wh

49、ile any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Void. i.2 Void. i.3 ETSI TR 102 273-4 (V1.2.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and evaluation of the corresponding measurement uncertaint