ETSI EN 300 474-1-2003 Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) Profile requirement list and profile specific Implementation Conformance Sta.pdf

《ETSI EN 300 474-1-2003 Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) Profile requirement list and profile specific Implementation Conformance Sta.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 474-1-2003 Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) Profile requirement list and profile specific Implementation Conformance Sta.pdf（57页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 300 474-1 V1.2.1 (2003-09)European Standard (Telecommunications series) Digital Enhanced Cordless Telecommunications (DECT);Generic Access Profile (GAP);Profile requirement list and profile specificImplementation Conformance Statement (ICS) proforma;Part 1: Portable radio Termination (PT)ET

2、SI ETSI EN 300 474-1 V1.2.1 (2003-09) 2 Reference REN/DECT-040107-1 Keywords access, DECT, generic, ICS, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucrati

3、f enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in

4、 contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the d

5、ocument may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be

6、 reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2003. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its

7、 Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI EN 300 474-1 V1.2.1 (2003-09) 3 Contents Intellectual P

8、roperty Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .7 4 Conformance requirement concerning profile ICS 7 Annex A (normative): Requirement lists for DECT PT .8 A.1 General .8 A.1.1 Profile Requirement List (profile RL)8 A.1.2 Gener

9、al conditions9 A.2 Network (NWK) layer - PT: profile requirement list (profile RL).9 A.2.1 Major capabilities.9 A.2.1.1 Entities 9 A.2.1.2 CC features .10 A.2.1.3 MM features11 A.2.1.4 SS features (services)12 A.2.1.5 LCE features .13 A.2.1.6 Procedures.13 A.2.2 Messages 15 A.2.2.1 Call control mess

10、ages .15 A.2.2.2 MM messages .22 A.2.2.3 Connection-related and connection independent supplement service messages.28 A.2.2.4 Link Control Entity (LCE) messages28 A.2.3 Information elements29 A.2.3.1 Fixed length information element support29 A.2.3.2 Variable length information element supported30 A

11、.2.3.3 Escape information elements support .34 A.2.4 Protocol error handling.35 A.3 Data Link Control (DLC) layer - PT: profile ICS 35 A.3.1 Capabilities.35 A.3.1.1 Services.35 A.3.1.1.1 C-plane services 36 A.3.1.1.2 U-plane services36 A.3.1.1.3 Management services 36 A.3.1.2 Procedures.37 A.3.1.2.1

12、 Generic signalling procedures.37 A.3.1.2.2 Class A procedures37 A.3.1.2.3 Broadcast procedures 37 A.3.1.2.4 LU1 procedures.37 A.3.1.2.5 Management procedures .38 A.3.1.3 Parameters.38 A.3.1.3.1 LU1 parameters.38 A.3.1.4 Messages.39 A.3.1.4.1 C-plane PDUs .39 A.4 Medium Access Control (MAC) layer -

13、PT: profile ICS .39 A.4.1 Major capabilities.39 A.4.1.1 Services.39 A.4.1.1.1 Connection oriented control services 39 A.4.1.1.2 Broadcast control services.40 ETSI ETSI EN 300 474-1 V1.2.1 (2003-09) 4 A.4.1.1.3 Multiplexing services 40 A.4.1.1.4 Management services 41 A.4.1.2 Procedures.42 A.4.1.2.1

14、Connection setup procedures 42 A.4.1.2.2 Connection data transfer procedures .42 A.4.1.2.3 Connection handover procedures 42 A.4.1.2.4 Connection release procedures43 A.4.1.2.5 Broadcast procedures 43 A.4.1.2.6 CSF multiplexing procedures43 A.4.1.2.7 Layer management procedures43 A.4.1.3 Other capab

15、ilities 44 A.4.2 Messages 44 A.4.2.1 A-Field44 A.4.2.1.1 A-field header - B-field identification.44 A.4.2.2 A-Field Messages .45 A.4.2.2.1 Paging tail messages supported.45 A.4.2.2.2 PTmessages information type .45 A.4.2.2.3 MAC control messages supported.46 A.4.2.2.4 Broadcast and connectionless (B

16、CL) messages 46 A.5 PhysicaL (PHL) layer - PT: profile ICS.47 A.5.1 Physical layer procedures.47 Annex B (normative): GAP profile-specific ICS proforma for PT .48 B.1 Introduction for completing the profile-specific ICS proforma .48 B.1.1 Purposes and structure48 B.1.2 Instructions for completing th

17、e profile-specific ICS proforma.50 B.2 Identification of the implementation 50 B.2.1 Date of statement50 B.2.2 Implementation Under Test (IUT) identification .50 B.2.3 System Under Test (SUT) identification50 B.2.4 Product supplier51 B.2.5 Client identification51 B.2.6 Contact person identification5

18、1 B.3 Identification of the profile.52 B.3.1 Defect report numbers and amendments implemented.52 B.3.2 Addenda implemented52 B.4 Global statement of conformance.52 B.5 Capabilities.53 B.5.1 NWK profile-specific ICS proforma for PT.53 B.5.1.1 General requirements53 B.5.1.2 Application features53 B.5.

19、1.3 Application procedures .53 B.5.1.4 Management procedures .54 B.5.2 DLC profile-specific ICS proforma for PT 54 B.5.3 MAC profile-specific ICS proforma for PT .54 B.5.3.1 Services.54 B.5.3.1.1 Extended frequency allocation service54 B.5.4 PHY profile-specific ICS proforma for PT 55 B.5.4.1 Requir

20、ements 55 Annex C (informative): Bibliography.56 History 57 ETSI ETSI EN 300 474-1 V1.2.1 (2003-09) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly a

21、vailable for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web s

22、erver (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may

23、 be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DECT). The present document is part 1 of a multi-part deliverable covering the Digital Enhanced Cordless

24、Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICS) proforma, as identified below: Part 1: “Portable radio Termination (PT)“. Part 2: “Fixed radio Termination (FT)“. Annex A contains the requirement lists f

25、or the Portable radio Termination (PT) Generic Access Profile. Annex B contains the profile-specific ICS proforma for the PT Generic Access Profile. National transposition dates Date of adoption of this EN: 5 September 2003 Date of latest announcement of this EN (doa): 31 December 2003 Date of lates

26、t publication of new National Standard or endorsement of this EN (dop/e): 30 June 2004 Date of withdrawal of any conflicting National Standard (dow): 30 June 2004 ETSI ETSI EN 300 474-1 V1.2.1 (2003-09) 6 1 Scope The present document provides the profile Requirement List and profile-specific Impleme

27、ntation Conformance Statement (profile ICS) proforma for the Digital Enhanced Cordless Telecommunications (DECT) Generic Access Profile (GAP) at the Portable radio Termination (PT) as defined in EN 300 444 2 in compliance with the relevant requirements and in accordance with the relevant guidance gi

28、ven in ISO/IEC 9646-7 8. The supplier of an implementation which is claimed to conform to EN 300 444 2 is required to complete a copy of the Protocol Implementation Conformance Statement (PICS) proforma EN 300 476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300 476-7 6 with the replacements from anne

29、x A of the present document, as well as, a copy of the and profile-specific ICS proforma provided in annex B of the present document. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either sp

30、ecific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected

31、 location might be found at http:/docbox.etsi.org/Reference. 1 ETSI EN 300 175-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 5: Network (NWK) layer“. 2 ETSI EN 300 444: “Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP)“. 3 ETSI

32、EN 300 476-1: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 1: Network (NWK) layer - Portable radio Termination (PT)“. 4 ETSI EN 300 476-2: “Digital Enhanced Cordless Telecommunications (DECT); Common

33、Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 2: Data Link Control (DLC) layer - Portable radio Termination (PT)“. 5 ETSI EN 300 476-3: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PI

34、CS) proforma; Part 3: Medium Access Control (MAC) layer - Portable radio Termination (PT)“. 6 ETSI EN 300 476-7: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Protocol Implementation Conformance Statement (PICS) proforma; Part 7: Physical layer“. 7 ISO/IEC 9646-1 (1994

35、): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework -Part 1: General concepts“. (See also X.290 (1991). 8 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Impl

36、ementation Conformance Statements“. ETSI ETSI EN 300 474-1 V1.2.1 (2003-09) 7 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646-7 8, EN 300 444 2 and in ISO/IEC 9646-1 7 apply. 3.2 Abbreviations For the purposes

37、of the present document, the abbreviations defined in ISO/IEC 9646-1 7 and EN 300 444 2 apply. 4 Conformance requirement concerning profile ICS The supplier of a protocol implementation which is claimed to conform to the portable termination specific requirements of EN 300 444 2 shall verify that hi

38、s protocol implementation meets the profile Requirements Lists (RLs) for each DECT protocol layer, contained in annex A of the present document, and shall complete a copy of the profile-specific ICS proforma provided in annex B and shall provide the information necessary to identify both the supplie

39、r and the implementation. ETSI ETSI EN 300 474-1 V1.2.1 (2003-09) 8 Annex A (normative): Requirement lists for DECT PT A.1 General The supplier of a protocol implementation which is claimed to conform to the portable termination specific requirements of EN 300 444 2 shall verify that his particular

40、NetWorK (NWK), Data Link Control (DLC), Medium Access Control (MAC) and PHL layer protocol implementation meets the profile RL for this layer. For this, he shall complete a copy of the corresponding layer PICS proforma contained in annex A of EN 300 476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300

41、 476-7 6 updated with the requirements from this annex. A.1.1 Profile Requirement List (profile RL) The profile Requirement List (profile RL) for the NWK, DLC, MAC and PHL layers as defined in this annex is based on EN 300 476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300 476-7 6. For every capabil

42、ity listed in EN 300 476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300 476-7 6, the profile requirements are expressed by restriction upon allowed support answers in EN 300 476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300 476-7 6. The profile RL is produced by copying selected tables from EN 300

43、476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300 476-7 6, removing the column(s) to be completed by the supplier, and adding a new set of columns giving the new profile requirements, both in terms of the status and allowed values. The tables are referenced by preceding it with EN 300 476-1 3, EN 3

44、00 476-2 4, EN 300 476-3 5 or EN 300 476-7 6 as relevant. Profile status column: The standardized symbols for the status column are as follows: m or M mandatory - the capability is required to be supported; o or O optional - the capability may be supported or not; n/a or N/A not applicable - in the

45、given context, it is impossible to use the capability; x or X prohibited (excluded) - there is a requirement not to use this capability in the given context; o.i or O.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of

46、related optional items and the logic of their selection which is defined immediately following the table; ci or Ci conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditiona

47、l status expression which is defined immediately following the table or which is defined in the general condition table below; i or I out-of-scope - this capability is outside the scope of the given specification, and hence irrelevant and not subject to conformance testing. This status is in particu

48、lar applicable for data fields which are reserved for future use. The structure of such fields has to be supported, but the value is undefined and thus to be ignored. Reference column: The reference column gives reference to EN 300 444 2, except where explicitly stated otherwise. ETSI ETSI EN 300 47

49、4-1 V1.2.1 (2003-09) 9 A.1.2 General conditions The note in table A.1 is generally defined to apply to the tables in the following clauses where indicated. Table A.1: General condition table Condition identifier Condition definition NOTE A: The status of the relevant item is exactly as the status of this item in EN 300 476-1 3, EN 300 476-2 4, EN 300 476-3 5 and EN 300 476-7 6. The item has been included as the profile reference column includes reference to