ETSI EN 300 394-4-4-2001 Terrestrial Trunked Radio (TETRA) Conformance Testing Specification Part 4 Protocol Testing Specification for Direct Mode Operation (DMO) Sub-Part 4 Test S.pdf

《ETSI EN 300 394-4-4-2001 Terrestrial Trunked Radio (TETRA) Conformance Testing Specification Part 4 Protocol Testing Specification for Direct Mode Operation (DMO) Sub-Part 4 Test S.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 394-4-4-2001 Terrestrial Trunked Radio (TETRA) Conformance Testing Specification Part 4 Protocol Testing Specification for Direct Mode Operation (DMO) Sub-Part 4 Test S.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI EN 300 394-4-4 VI .I .I (2001-01) European Standard (Telecommunications series) Terrestrial Trunked Radio (TETRA); Conformance testing specification; Part 4: Protocol testing specification for Direct Mode Operation (DMO); Sub-part 4: Test Suite Structure and Test Purposes (TSS Essential, or pot

2、entially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server ClattD:/www.etsP.c/iDr. Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI.

3、No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Project

4、Terrestrial Trunked Radio (TETRA). The present document had been submitted to Public Enquiry as ETS 300 394-4-4. During the processing for Vote it was converted into an EN. The present document is part 4 of a multi-part deliverable covering the Terrestrial Trunked Radio (TETRA); Conformance testing

5、specification, as identified below: Part 1: “Radio“; Part 2: Part 3: Part 4: Part 5: “Security“. “Protocol testing specification for Voice plus Data (V+D)“; “Protocol testing specification for Packet Data Optimized (PDO)“; “Protocol testing specification for Direct Mode Operation (DMO)“; National tr

6、ansposition dates Date of adoption of this EN Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of this EN (dop/e): Date of withdrawal of any conflicting National Standard (dow): 22 December 2000 31 March 2001 30 September 2001 30 Septem

7、ber 2001 ETSI 5 ETSI EN 300 394-4-4 V1.l.l (2001-01) 1 Scope EN 300 394-4 contains the Test Suite Structure (TSS) and Test Purposes (TPs) to test the TETRA Direct Mode Operation (DMO) protocols. EN 300 394-4 is divided into several parts, each one dealing with a different set of layer 3 and layer 2

8、DMO protocols. The present document deals with TSS Technical requirements for Direct Mode Operation (DMO); Part 4: Type 1 repeater Air Interface“. ETSI EN 300 396-8-2: “TETRA; Direct Mode Operation (DMO); Part 8: Protocol Implementation Conformance Statement (PICS) proforma specification; Part 8-2:

9、Type 1 repeater Air Interface“. ISO/IEC 9646-1 (1995): “Information technology - Open Systems Interconnection - Conformance Testing Methodology and Framework - Part 1: General Concepts“. (See also ITU-T Recommendation X.290). ISO/IEC 9646-2 (1995): “Information technology - Open Systems Interconnect

10、ion - Conformance Testing Methodology and Framework - Part 2: Abstract Test Suite Specification“. (See also ITU-T Recommendation X.291). ETSI ETS 300 406 (1995): “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 121 1

11、31 141 151 ETSI 6 ETSI EN 300 394-4-4 V1.l.l (2001-01) 3 Def i n it ions and abbreviations 3.1 TETRA d ef i nit ions For the purposes of the present document, the terms and definitions given in EN 300 396-4 i apply. 3.2 TETRA abbreviations For the purposes of the present document, the following abbr

12、eviations apply: CM DMCC DMO FCS ITS1 MAC MNI MS NWK Rx SDS SDU TX Circuit Mode Direct Mode Call Control Direct Mode of Operation Frame Check Sequence Individual TETRA Subscriber Identity Medium Access Control Mobile Network Identity Mobile Station Network. Layer 3 of the TETRA protocol stack Receiv

13、er Short Data Services Service Data Unit Transmitter 3.3 IS0 9646 abbreviations For the purposes of the present document the following ISOLEC 9646-1 3 abbreviations apply: IUT Implementation Under Test IXIT PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement PIXIT TP Test Purpo

14、se TSS Test Suite Structure Implementation extra Information for Testing Protocol Implementation extra Information for Testing ETSI 7 ETSI EN 300 394-4-4 V1.l.l (2001-01) TP-Name The TP name is a unique identifier, specified according to the TP naming conventions defined in clause 5.2. (It is also t

15、he name of the corresponding test case). 4 Requirement ref: reference to the paragraph number of specification EN 300 396-4 l stating this conformance requirement. For example: EN 300 396-4 l, 6.2.5.1. 4.1 Pur pose Selection cond Test description Pass criteria Preamble Postam ble Test Suite Structur

16、e (TSS) Purpose of the test itself, indicating for example the test performed against a requirement of the protocol, described by this test purpose. Example: test of changeover initiated from RX reservation state. Expression based on EN 300 396-8-2 2 PICS statements, used to select or deselect the c

17、orresponding test case according to the options of the implementation. Body of the test. Visible action to be observed at PCO to declare that the IUT passes the test and conforms to the specifications. “None“ or name of the preamble procedure bringing the IUTfrom idle state to the state required to

18、run the test. “None“ or name of the oostamble to brina the IUT back to idle state. MAC layer test groups The first level of the MAC test groups separates the MAC test suite in functional test groups: CA, BV and TI. The following list defines the MAC layer test group names and identifiers: - DM-REP1

19、MAC layer (DMO-DMREPlMAC) - Capability tests (CA) - Valid behaviour tests (BV) - Invalid behaviour tests (BI) - Timer tests (TI) 4.2 Test g roup descri pt ion Capability (CA) tests provide limited testing that the observable capabilities of the IUT are in accordance with the conformance requirements

20、 and the additional capabilities claimed in the PICSPIXIT. The Valid Behaviour (BV) group tests an IUT in response to valid behaviour of the test system. “Valid“ means that a test event is syntactically and contextually correct. All test cases in the valid behaviour group are intended to verify as t

21、horoughly as possible the various functions of the protocol. Different timers are defined to supervise the various state transitions. The Timer (TI) test group is intended to verify that the IUT is reacting properly to an expiry of one of the timers or to a counter mismatch. 5 Introduction to Test P

22、urposes (TPs) The test purposes are defined in clause 6 of the present document for MAC layer. 5.1 Test purpose definition conventions Each TP is described using text presented in a table. The table contains the following information: Table 1 ETSI 8 Pur pose Test description Pass criteria Selection

23、EN 300 396-8-2 2 Preamble Postam ble ETSI EN 300 394-4-4 V1.l.l (2001-01) Fill bit addition and deletion mechanism. The main tester initiates a CM or SDS call according to IUT capabilities, by transmitting to the IUT a DMAC-SYNC PDU containing the appropriate PDU. Check that the IUT re-transmits the

24、 DMAC-SYNC PDU containing identical PDU to the parallel tester, meaning that the IUT fill bit deletion and addition mechanism works properly. A.3211 or A.3212 None. Free DM channel. IUT supports circuit mode call; IUT supports Short Data Services. 5.2 Test purpose naming conventions The identifier o

25、f a test purpose is built according to table 2: Table 2: Test purpose naming convention D M O/ctt/css/c n n cts =test suite type DMREP1 DM Repeater type 1 tt = Type of testing CA BV BI TI Capability Tests Valid Behaviour Tests Invalid Behaviour Tests Timer expiry and counter mismatch tests Icnn = se

26、auential number o1 -99 Test PurDose Number 5.3 Selection expressions A test case, based on a test purpose described here, can be selected or deselected from the test suite, according to the evaluation of selection expressions which reflect the capabilities supported or not by the implementation unde

27、r test. 6 DM-REP1 test purposes In this test purpose description, the following test configuration is defined: the IUT is a DM-REP1. The main tester is a MS connected to a Repeater type 1 (MS-REP1) and it plays the role of the master of the call. A parallel tester plays the role of the slave. Most o

28、f the tests verify that the repeater re-transmits properly what is received from the main tester to the parallel tester, and from the parallel tester to the main one. 6.1 DM-REP1 MAC layer 6.1 .I DM-REP1 MAC capability tests ETSI 9 ETSI EN 300 394-4-4 V1.l.l (2001-01) Pur pose Test description Pass

29、criteria Presence signal I DMO-M SREP1 -MAC-CA-OP IReference: EN 300 396-4 l, 9.4.5.1 Check sending of presence signal. The main tester is connected to the DM REP1 and the DM channel is free. Check that the IUT sends at irregular intervals between DT253 and DT254 time a Pur pose Test description Pas

30、s criteria IDPRES-SYNC PDU, in the DSB: in all four slots of DN253 consecutive frames. Selection IA.40/2 IUT sends DPRES-SYNC. Check DM-REP channel surveillance when idle at DM-MS call Set-up; Check retransmission of signalling message received from master DM-MS. The tester initiates a CM or SDS cal

31、l, according to IUT capabilities. It translates into a DMAC-SYNC PDU with master/slave link flag set to 1, communication type element=01, 1 O bit repeater address. Verify that the IUT accepts the call and re-transmits the signalling information (it retransmits the DMAC-SYNC PDU containing the DM-SET

32、UP or DM-SETUP PRES IEN 300 396-8-2 r21 I I EN 300 396-8-2 2 Preamble Postam ble IPnntamhle INnnn I or A.3212 None. Free DM channel. IUT supports Short Data Services. 6.1.2 DM-REP1 MAC valid behaviour tests Pass criteria Selection parallel tester. The parallel tester answers with DM-CONNECT contaiie

33、d in a DMAC-SYNC with master/slave link flag set to O, communication type 01, its own 1 O bit repeater address. Verify that the IUT re-transmits to the main tester the DMAC-SYNC containing DM-CONNECT where master/slave flag is set to 1. A.32/1 IUT supports circuit mode call. lor DM-SDS DATA or DM-SD

34、S UDATA SDU,-with master/slave link flag set to O). Selection IA.32/1 IUT supports circuit mode call; Pass criteria Selection parallel tester. The parallel tester answers with DM-CONNECT. Verify that the IUT re-transmits the DM-CONNECT to the main tester. A.32/1 IUT supports circuit mode call. DMO-D

35、M REPl-MAC-BV-O2 Pur pose Test descriDtion IReference: EN 300 396-4 l, 9.5.2.1 ICheck retransmission of signalling message received from a slave DM-MS. IThe main tester initiates a DM-SETUP PRES which is re-transmitted bv the IUT to the Preamble INone. Postam ble IFree DM channel. DMO-DM REP1-MAC-BV

36、-03 Pur pose Test description IReference: EN 300 396-4 l, 9.4.4.1, 9.6.2.2 ICheck DM-REP procedure: set up with presence check. IThe main tester initiates a DM-SETUP PRES which is re-transmitted by the IUT to the Preamble INone. Postam ble IFree DM channel. ETSI 10 ETSI EN 300 394-4-4 V1.l.l (2001-0

37、1) Pass criteria Selection EN 300 396-8-2 2 DMO-DM REP1-MAC-BV-04 Pur pose Test description IReference: EN 300 396-4 l, 9.4.4.1, 9.6.2.2 ICheck DM-REP procedure: set up with presence check. IThe main tester initiates a DM-SETUP PRES which is re-transmitted by the IUT to the parallel tester. The para

38、llel tester answers with DM-DISCONNECT. Verify that the IUT re-transmits the DM-DISCONNECT to the main tester. A.32/1 IUT supports circuit mode call. Pur pose Test description Preamble INone. Postam ble IFree DM channel. Check DM-REP procedure: set up with presence check. The main tester initiates a

39、 DM-SETUP PRES which is re-transmitted by the IUT to the parallel tester. The parallel tester answers with DM-CONNECT. The IUT re-transmits IDMO-DM REP1-MAC-BV-05 IReference: EN 300 396-4 l, 9.4.4.1, 9.6.2.2 Selection Preamble EN 300 396-8-2 2 retransmits the traffic. A.32/1 None. IUT supports circu

40、it mode call. Ithe DM-CONNECTto the main tester, which issues a DM-CONNECT ACK. IVerifv that the IUT re-transmits DM-CONNECT ACK to the parallel tester and then Pass criteria Pur pose Test description Pass criteria Selection Preamble Postam ble EN 300 396-8-2 2 Check DM-REP procedure: set up with pr

41、esence check. The main tester initiates a DM-SETUP PRES which is re-transmitted by the IUT to the parallel tester. The parallel tester answers with DM-CONNECT. The IUT re-transmits the DM-CONNECT to the main tester, which issues a DM-RELEASE. Verify that the IUT re-transmits DM-RELEASE to the parall

42、el tester and then returns the channel to idle. A.32/1 None. None. IUT supports circuit mode call. Pass criteria Selection DMO-DM REP1-MAC-BV-07 Pur pose Test description IReference: EN 300 396-4 l, 9.5.1.1.2, 9.6.2.1 IRe-transmission procedure: set up without presence check. IThe main tester initia

43、tes a DM-SETUP which is re-transmitted by the IUT to the parallel tester. Verify that the IUT re-transmits the DM-SETUP to the parallel tester in all four slots of DN232 frames. A.32/1 IUT supports circuit mode call. Selection Preamble Postam ble EN 300 396-8-2 2 Preamble INone. Postam ble IFree DM

44、channel. parallel tester in all four slots of DN233 frames. A.32/2 None. None. IUT supports Short Data Services. DMO-DM REP1-MAC-BV-08 Pur pose Test description IReference: EN 300 396-4 l, 9.5.1.1.3 IRe-transmission procedure: DM-SDS DATA or DM-SDS UDATA. IThe main tester initiates a DM-SDS DATA or

45、DM-SDS UDATA which is Ire-transmitted by the IUT to the parallel tester. IVerify that the IUT re-transmits the DM-SDS DATA or DM-SDS UDATA to the Pass criteria ETSI 11 ETSI EN 300 394-4-4 V1.l.l (2001-01) Selection Preamble Postam ble EN 300 396-8-2 2 DMO-DM REP1-MAC-BV-O9 Pur pose I Fragmentation.

46、Test description IReference: EN 300 396-4 l, 9.5.1.1.3 IThe main tester initiates a SDS by transmitting DM-SDS DATA or DM-SDS UDATA flag set to value 1, followed by n times DMAC-FRAG then ending with DMC-END. A.32/2 Short Data Service (SDS). None. None. IPDU with data type 2, 3 or 4 in order to gene

47、rate a fragmented message. Icheck that the parallel tester receives from the IUT: DMAC-SYNC with Fragmentation Pass criteria Pur pose Test description Pass criteria retransmission of message. The main tester initiates a command such as DM-CONNECT. check that the IUT re-transmits the DMAC-SYNC PDU co

48、ntaining this command without changing slot, frame numbers and frame countdown, only the master/slave link flaa is chanaed to O. Selection Preamble Postam ble None. None. None. 6.1.3 DM-REP MAC invalid behaviour tests Pur pose Test description Pass criteria Selection EN 300 396-8-2 2 Preamble Postam

49、 ble Check DM-REP channel surveillance when idle at DM-MS call Set-up, wrong address. The tester initiates a CM or SDS call, according to IUT capabilities, but not containing the 1 O-bit repeater address. Verify that the IUT ignores the call and does not re-transmit the signalling information to the parallel tester. A.32/1 or A.3212 None. Free DM channel. IUT supports circuit mode call; IUT supports Short Data Services. Pur pose Test description Pass criteria Selection Preamble INone. Postam ble IFree DM channel. Check absence of retransmission o