ETSI EN 300 338-2-2017 Technical characteristics and methods of measurement for equipment for generation transmission and reception of Digital Selective Calling (DSC) in the mariti_1.pdf

《ETSI EN 300 338-2-2017 Technical characteristics and methods of measurement for equipment for generation transmission and reception of Digital Selective Calling (DSC) in the mariti_1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 338-2-2017 Technical characteristics and methods of measurement for equipment for generation transmission and reception of Digital Selective Calling (DSC) in the mariti_1.pdf（49页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 300 338-2 V1.4.1 (2017-02) Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 2: Class A/B DSC EUROPEAN STANDARD ETSI ETSI EN 300 338-2 V1.

2、4.1 (2017-02) 2 Reference REN/ERM-TG26-087-2 Keywords DSC, GMDSS, maritime, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Gras

3、se (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified wit

4、hout the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of

5、the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your

6、comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETS

7、I. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo

8、are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 338-2 V1.4.1

9、 (2017-02) 3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions and abbreviations . 8g33.1 Definitions 8g33.2 Abbreviations . 10g34 Controls and Indicators in Class A/B

10、 DSC Equipment 10g34.1 Visual indication 10g35 Technical requirements 10g35.1 Facilities for DSC transmission and reception . 10g35.1.1 Multi-frequency distress alert attempts and watch receiver capabilities (MF/HF) . 10g35.1.2 Watch receiver capabilities (VHF) . 10g35.2 Remote alarms 11g35.3 Galvan

11、ic isolation . 11g35.4 Manuals 11g36 Automated and Non-Automated Procedure Requirements in Class A/B DSC Equipment 11g36.1 Introduction 11g36.2 Non-automated features . 11g36.2.0 General 11g36.2.1 DSC Message Composition 12g36.2.2 Transmission of DSC messages and prioritized wait 13g36.2.3 Alarms 13

12、g36.3 Standby . 13g36.4 Sending distress automated procedure . 15g36.4.1 Procedure 15g36.4.2 Tasks . 17g36.4.3 Display 17g36.4.3.0 General Display Requirements 17g36.4.3.1 Examples of sending distress procedure displays on VHF equipment 18g36.4.4 Dedicated distress button sub procedure . 19g36.4.5 T

13、ransmission of the alert attempt 20g36.4.6 Updating position 20g36.4.7 Handling received DSC Messages 20g36.4.8 Alarms 20g36.4.9 Determining Subsequent communications 21g36.4.10 Automated tuning . 21g36.4.11 Cancelling the Distress Alert 21g36.4.11.0 General Requirements. 21g36.4.11.1 Examples of ca

14、ncel-distress displays on VHF equipment. 22g36.4.12 Acknowledgments 23g36.4.13 Termination. 23g36.4.14 Warnings . 23g36.5 Receiving distress automated procedure 23g36.5.1 Procedure 23g36.5.2 Tasks . 25g36.5.3 Display 25g36.5.3.0 General Display Requirements 25g36.5.3.1 Examples of received distress

15、procedure displays on VHF equipment . 26g36.5.4 Handling received DSC Messages 27g3ETSI ETSI EN 300 338-2 V1.4.1 (2017-02) 4 6.5.5 Alarms 27g36.5.6 Determining Subsequent communications 27g36.5.7 Automated tuning . 27g36.5.8 Acknowledgments 28g36.5.9 Sending Relays and Acknowledgments 28g36.5.10 Ter

16、mination. 28g36.5.11 Warnings . 28g36.6 Sending non-distress automated procedure 29g36.6.1 Procedure 29g36.6.2 Tasks . 29g36.6.3 Display 30g36.6.3.0 General Display Requirements 30g36.6.3.1 Examples of sending non-distress procedures displays on VHF equipment . 31g36.6.4 Handling received DSC Messag

17、es 31g36.6.5 Alarms 31g36.6.6 Automated tuning . 31g36.6.7 Delayed Acknowledgements 32g36.6.8 Termination. 32g36.6.9 Warnings . 32g36.7 Receiving non-distress automated procedure . 32g36.7.1 Procedure 32g36.7.2 Tasks . 34g36.7.3 Display 34g36.7.3.0 General Display Requirements 34g36.7.3.1 Examples o

18、f receiving non-distress procedures displays on VHF equipment . 35g36.7.4 Handling received DSC messages 36g36.7.5 Alarms 36g36.7.6 Automated tuning . 36g36.7.7 Acknowledgments 37g36.7.8 Termination. 37g36.7.9 Warnings . 37g36.8 Communications automated procedure 38g36.8.1 Procedure 38g36.8.2 Tasks

19、. 38g36.8.3 Display 38g36.8.4 Handling received DSC Messages 38g36.8.5 Tuning of the general receiver and transmitter . 38g36.8.6 Termination. 39g36.9 Multiple automated procedures and parallel event handling 39g36.9.1 Procedure 39g36.9.2 Tasks . 39g36.9.3 Examples of multiple procedure screens 40g3

20、Annex A (normative): DSC Message Composition . 41g3A.1 Default values . 41g3A.2 The default DROBOSE 42g3A.3 Allowable non-distress DSC message parameters . 42g3Annex B (normative): Radius-Centre point conversion and rounding algorithm . 43g3B.1 Radius-centre point conversion 43g3B.2 Rounding 44g3B.3

21、 Special cases for either form of area data entry . 44g3Annex C (normative): Automated Non-Distress Channel/Frequency Selection Algorithm 45g3C.0 General . 45g3C.1 VHF 45g3ETSI ETSI EN 300 338-2 V1.4.1 (2017-02) 5 C.2 HF . 45g3Annex D (normative): Alarms . 46g3D.1 Alarm specifications . 46g3D.2 Alar

22、ming with critical errors 47g3D.3 Default alarm sounds 47g3D.4 Other alarm sounds . 48g3History 49g3ETSI ETSI EN 300 338-2 V1.4.1 (2017-02) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to the

23、se essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest

24、 updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

25、 server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 2 of a multi-part deliverable. Full details

26、 of the entire series can be found in part 1 i.1. The present document covers the operator interfaces and operating system for Class A/B DSC equipment. National transposition dates Date of adoption of this EN: 8 February 2017 Date of latest announcement of this EN (doa): 31 May 2017 Date of latest p

27、ublication of new National Standard or endorsement of this EN (dop/e): 30 November 2017 Date of withdrawal of any conflicting National Standard (dow): 30 November 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“,

28、 “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 338-2 V1.4.1 (2017-02) 7 1 Scope The prese

29、nt document states the minimum requirements for equipment to be used for generation, transmission and reception of Class A or B Digital Selective Calling (DSC) for use on board ships. DSC is intended to be used in the Medium Frequency (MF), High Frequency (HF) and Very High Frequency (VHF) bands of

30、the Maritime Mobile Service (MMS), for both distress, safety and general communications. The present document is part 2 of a multi-part deliverable that covers the requirements to be fulfilled by equipment that is either integrated with a transmitter and/or a receiver or equipment that is a stand-al

31、one DSC terminal and has the following class of DSC: Class A: includes all the facilities defined in annex 1 of Recommendation ITU-R M.493-14 3 and complies with the IMO Global Maritime Distress and Safety System (GMDSS) carriage requirements for MF/HF installations and/or VHF installations; Class B

32、: provides minimum facilities for equipment on ships not required to use class A equipment and complies with the minimum IMO GMDSS carriage requirements for MF and/or VHF installations. This equipment should provide for: - alerting, acknowledgement and relay facilities for distress purposes; - calli

33、ng and acknowledgement for general communication purposes; and - calling in connection with semi-automatic/automatic services, as defined in Recommendation ITU-R M.493-14 3, annex 2, clause 3. These requirements include the relevant provisions of the ITU Radio Regulations 2 and Recommendations ITU-R

34、, the International Convention for the Safety Of Life At Sea (SOLAS), and the relevant resolutions of the International Maritime Organization (IMO). 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non

35、-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox

36、.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 “International Convention for the Safety of L

37、ife at Sea (SOLAS)“, 1974. 2 ITU Radio Regulations (2016). 3 Recommendation ITU-R M.493-14: “Digital selective-calling system for use in the maritime mobile service“. 4 IMO resolution MSC.97 (73), section 14.6.4: “International Code of Safety for High-Speed Craft, 2000 (2000 HSC Code)“. ETSI ETSI EN

38、 300 338-2 V1.4.1 (2017-02) 8 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referen

39、ced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist

40、the user with regard to a particular subject area. i.1 ETSI EN 300 338-1: “Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 1: Common requirements

41、“. i.2 MSC 302(87): “Adoption of performance standards for bridge alert management“. i.3 IEC 61924-2 Edition 1: “Maritime navigation and radiocommunication equipment and systems - integrated navigation systems - Part 2: Modular structure for INS - operational and performance requirements, methods of

42、 testing and required test results“, (including IEC 61924-2 Corrigendum 1 November 2013). 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 300 338-1 i.1 and the following apply: acknowledged: when the objective of th

43、e initial DSC message has been achieved active: automated procedure which has control of the general receiver and transmitter and is thus able to engage in subsequent communications and receive DSC messages on both the watch receiver and general receiver automated procedure: set of actions necessary

44、 to complete the objective of an initiating DSC message or non DSC communication event NOTE 1: Four DSC automated procedures are designed to process these. They are the receiving of distress DSC messages, the receiving of non-distress DSC messages, the sending of distress DSC alert attempts and the

45、sending of non-distress DSC messages. In addition a fifth procedure is designed to handle non DSC communication events. NOTE 2: These automated procedures are called: square4 Received distress automated procedure. square4 Sending distress automated procedure. square4 Received non-distress automated

46、procedure. square4 Sending non-distress automated procedure. square4 Communications automated procedure. default: value selected or an action taken by the equipment software in the absence of any operator input distress DSC message: DSC message or acknowledgement containing the distress information

47、distress event: unique distress situation identified by two (VHF) or three (MF/HF) parameters of the distress information; the MMSI of the vessel in distress and the nature of distress and on MF/HF the mode of subsequent communication ETSI ETSI EN 300 338-2 V1.4.1 (2017-02) 9 engaged: equipment that

48、 is busy handling an automated procedure factory default: default value that is set by the manufacturer such that the field or behaviour is defined prior to any operator intervention general receiver: receiver part of the transceiver used for the reception of all subsequent communications and on HF

49、the reception of DSC acknowledgements on the duplex DSC channels NOTE: It is important to distinguish this unit from the watch receiver. information characters: set of symbols in a DSC message that contains the items of interest for the recipient and is used to compute the ECC symbol that terminates the message NOTE: These symbols are repeated in the DX/RX time diversity pattern. initial DSC message: DSC message that starts an automated procedure non-distress DSC message: DSC messages or acknowledgments that do not have the format specifier or cate