ETSI EN 300 220-4-2017 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 4 Harmonised Standard covering the essential requirements of article 3 2 _1.pdf

《ETSI EN 300 220-4-2017 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 4 Harmonised Standard covering the essential requirements of article 3 2 _1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 220-4-2017 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 4 Harmonised Standard covering the essential requirements of article 3 2 _1.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 300 220-4 V1.1.1 (2017-02) Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 4: Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Metering devices operating in designated band 169,400 MHz to 169,475 MHz HARMONI

2、SED EUROPEAN STANDARD ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 2 Reference DEN/ERM-TG28-538 Keywords harmonised standard, radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Associ

3、ation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print

4、 versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on

5、a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If

6、 you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and

7、microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rig

8、hts reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and

9、owned by the GSM Association. ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitions, symbols and abbreviations .

10、8g33.1 Definitions 8g33.2 Symbols 8g33.3 Abbreviations . 8g34 Technical requirements specifications . 8g34.1 Environmental profile . 8g34.2 All equipment conformance requirements . 8g34.2.0 Compliance . 8g34.2.1 Operating frequency . 9g34.2.1.0 Applicability 9g34.2.1.1 Description 9g34.2.1.2 Limits

11、9g34.2.1.3 Conformance . 9g34.2.2 Unwanted emissions in the spurious domain 9g34.2.2.0 Applicability 9g34.2.2.1 Description 9g34.2.2.2 Limits 9g34.2.2.3 Conformance . 9g34.3 Transmitters conformance requirements 9g34.3.1 Effective Radiated Power . 9g34.3.1.0 Applicability 9g34.3.1.1 Description 9g34

12、.3.1.2 Limits 9g34.3.1.3 Conformance . 10g34.3.2 Duty Cycle 10g34.3.2.0 Applicability 10g34.3.2.1 Description 10g34.3.2.2 Limits 10g34.3.2.3 Conformance . 10g34.3.3 Occupied Bandwidth. 10g34.3.3.0 Applicability 10g34.3.3.1 Description 10g34.3.3.2 Limits 10g34.3.3.3 Conformance . 10g34.3.4 TX Out Of

13、Band Emissions 10g34.3.4.0 Applicability 10g34.3.4.1 Description 10g34.3.4.2 Limits 11g34.3.4.3 Conformance . 11g34.3.5 Transient power 11g34.3.5.0 Applicability 11g34.3.5.1 Description 11g34.3.5.2 Limits 11g34.3.5.3 Conformance . 11g34.3.6 Adjacent Channel Power 11g34.3.6.0 Applicability 11g3ETSI E

14、TSI EN 300 220-4 V1.1.1 (2017-02) 4 4.3.6.1 Description 11g34.3.6.2 Limits 11g34.3.6.3 Conformance . 12g34.3.7 TX behaviour under Low Voltage Conditions 12g34.3.7.0 Applicability 12g34.3.7.1 Description 12g34.3.7.2 Limits 12g34.3.7.3 Conformance . 12g34.4 Receivers conformance requirements . 12g34.4

15、.1 RX sensitivity . 12g34.4.1.0 Applicability 12g34.4.1.1 Description 12g34.4.1.2 Limits 12g34.4.1.3 Conformance . 12g34.4.2 Blocking 12g34.4.2.0 Applicability 12g34.4.2.1 Description 13g34.4.2.2 Limits 13g34.4.2.3 Conformance . 13g34.4.3 Clear Channel Assessment threshold 13g34.4.3.0 Applicability

16、13g34.4.3.1 Description 13g34.4.3.2 Limits 13g34.4.3.3 Conformance . 13g34.4.4 Polite spectrum access timing parameters 13g34.4.4.0 Applicability 13g34.4.4.1 Description 13g34.4.4.2 Limits 13g34.4.4.3 Conformance . 13g3Annex A (informative): Relationship between the present document and the essentia

17、l requirements of Directive 2014/53/EU . 14g3Annex B (normative): EU designated frequency bands for metering equipment 15g3Annex C (informative): Application form for testing 16g3C.0 Introduction 16g3C.1 Information as required by ETSI EN 300 220-4 16g3Annex D (informative): Selection of technical p

18、arameters . 18g3D.1 Introduction 18g3D.2 Receiver parameters . 18g3Annex E (informative): Bibliography . 19g3Annex F (informative): Change History 20g3History 21g3ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document ma

19、y have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI s

20、tandards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs no

21、t referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM)

22、. The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on t

23、he market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the p

24、resent document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. For non EU countries the present docu

25、ment may be used for regulatory (Type Approval) purposes. National transposition dates Date of adoption of this EN: 27 January 2017 Date of latest announcement of this EN (doa): 30 April 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 October 2017 Date

26、of withdrawal of any conflicting National Standard (dow): 31 October 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rule

27、s (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 6 Introduction The present document is part 4 of a multi-part deliverable covering Metering devices in the design

28、ated frequency range 169,400 MHz to 169,475 MHz. The present document is structured as follows: Clause 2 provides references. Clause 3 provides definitions of terms and abbreviations used. Clause 4 provides technical requirements. Annex A (informative): provides relationship between the present docu

29、ment and essential requirements of Directive 2014/53/EU i.1. Annex B (normative): EU designated frequency bands for metering equipment. Annex C (informative): Application form for testing. Annex D (informative): Selection of parameters. Annex E (informative): Bibliography. Annex F (informative): Cha

30、nge History. ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 7 1 Scope The present document specifies technical characteristics and methods of measurements for Metering Devices category equipment types: Metering devices category is defined by the EU Commission Decision 2013/752/EU i.2 as: “The metering devi

31、ce category covers radio devices that are part of bidirectional radio communications systems which allow remote monitoring, measuring and transmission of data in smart grid infrastructures, such as electricity, gas and water“. The present document covers equipment intended for fixed, mobile or nomad

32、ic use, e.g.: stand-alone radio equipment; plug-in radio devices intended for use with or within a variety of host systems; plug-in radio devices intended for use within combined equipment. These radio equipment types are capable of operating in the metering designated frequency band given in table

33、1. Table 1: Metering SRDs frequency band Metering Short Range Devices frequency range Transmit and receive 169,400 MHz to 169,475 MHz The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.1 under the conditions identified in annex A. 2 References 2.1 Normati

34、ve references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: Whil

35、e any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 220-1 (V3.1.1) (02-2017): “Short Range Devices (SRD) operating i

36、n the frequency range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited ver

37、sion applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents ar

38、e not necessary for the application of the present document but they assist the user with regard to a particular subject area. ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 8 i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Mem

39、ber States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC (RED Directive). i.2 Commission Decision 2013/752/EU on harmonisation of the radio spectrum for use by short-range devices as amended by subsequent Commission Decisions. i.3 ETSI EG 203 336

40、: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.4 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a sta

41、ndardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.5 Commission Decision 2000/299/EU on harmonisa

42、tion of the radio spectrum for use by short-range devices as amended by subsequent Commission Decisions. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the RE-Directive i.1 and ETSI EN 300 220-1 1 apply. 3.2 Symbo

43、ls For the purposes of the present document, the symbols given in ETSI EN 300 220-1 1 apply. 3.3 Abbreviations For the purposes of the present document, the abbreviations given in ETSI EN 300 220-1 1 apply. 4 Technical requirements specifications 4.1 Environmental profile The technical requirements

44、of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document which are identified as applicable in annex A at all times when operating

45、within the boundary limits of the declared operational environmental profile. Normal and extreme tests conditions are defined in ETSI EN 300 220-1 1, clauses 4.3.3 and 4.3.4. 4.2 All equipment conformance requirements 4.2.0 Compliance When an operational frequency band is selected from annex B for t

46、he equipment under test, the equipment shall comply with all parameters, exclusions and notes from the row in annex B unless a different National Radio Interface applies. ETSI ETSI EN 300 220-4 V1.1.1 (2017-02) 9 4.2.1 Operating frequency 4.2.1.0 Applicability Clause 4.2.1 applies to all equipment.

47、4.2.1.1 Description For the purpose of the present document, the description in ETSI EN 300 220-1 1, clause 5.1.1 applies. 4.2.1.2 Limits The manufacturer may declare either one or more operating frequencies and operating channels. Operating channel(s) shall be entirely within operational frequency

48、bands allowed by annex B. 4.2.1.3 Conformance The conformance for this requirement shall be as defined in ETSI EN 300 220-1 1, clause 5.1.2. 4.2.2 Unwanted emissions in the spurious domain 4.2.2.0 Applicability Clause 4.2.2 applies to all equipment. 4.2.2.1 Description For the purpose of the present

49、 document, the description in ETSI EN 300 220-1 1, clauses 5.9.1.1 and 5.9.1.2 apply. 4.2.2.2 Limits The EUT shall comply with reference limits defined in ETSI EN 300 220-1 1, clause 5.9.2. 4.2.2.3 Conformance The conformance tests for this requirement shall be as defined in ETSI EN 300 220-1 1, clause 5.9.3. Conformance shall be established under normal test conditions. 4.3 Transmitters conformance requirements 4.3.1 Effective Radiated Power 4.3.1.0 Applicability Clause 4.3.1 applies to all transmitters. 4.3.1.1 Descriptio