ETSI EN 300 220-3-1-2016 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 3-1 Harmonised Standard covering the essential requirements of article _1.pdf

《ETSI EN 300 220-3-1-2016 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 3-1 Harmonised Standard covering the essential requirements of article _1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 220-3-1-2016 Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz Part 3-1 Harmonised Standard covering the essential requirements of article _1.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 300 220-3-1 V2.1.1 (2016-12) Short Range Devices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 3-1: Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Low duty cycle high reliability equipment, social alarms equipment operating

2、 on designated frequencies (869,200 MHz to 869,250 MHz) HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)2 Reference DEN/ERM-TG28-530 Keywords alarm, harmonised standard, radio, reliability, SRD ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 9

3、4 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in elec

4、tronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing d

5、ocument is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI docume

6、nts is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any

7、form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction

8、in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Or

9、ganizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g3Introduction 7g31 Scope 8g32 References 8g32.1 Normative references .

10、8g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 9g33.1 Definitions 9g33.2 Symbols 9g33.3 Abbreviations . 9g34 Technical requirements specifications . 9g34.1 Environmental profile . 9g34.2 Technical requirements for transmit mode . 10g34.2.1 Applicability . 10g34.2.2 Opera

11、ting Frequency and Channel 10g34.2.2.1 Description 10g34.2.2.2 Limits 10g34.2.2.3 Conformance . 10g34.2.3 Effective Radiated Power . 10g34.2.3.1 Description 10g34.2.3.2 Limits 10g34.2.3.3 Conformance . 10g34.2.4 Duty Cycle 11g34.2.4.1 Description 11g34.2.4.2 Limits 11g34.2.4.3 Conformance . 11g34.2.

12、5 Adjacent Channel Power 11g34.2.5.1 Description and Applicability . 11g34.2.5.2 Limits 11g34.2.5.3 Conformance . 11g34.2.6 Transmitter Frequency Error. 11g34.2.6.1 Description and Applicability . 11g34.2.6.2 Limits 12g34.2.6.3 Conformance . 12g34.2.7 Transmitter Transient Power. 12g34.2.7.1 Descrip

13、tion 12g34.2.7.2 Limits 12g34.2.7.3 Conformance . 12g34.2.8 Tx Behaviour under Low Voltage Conditions 12g34.2.8.1 Description and Applicability . 12g34.2.8.2 Limits 12g34.2.8.3 Conformance . 12g34.3 Technical requirements for all EUT . 12g34.3.1 Applicability . 12g34.3.2 Spurious Emissions . 12g34.3

14、.2.1 Description 12g34.3.2.2 Limits 13g34.3.2.3 Conformance . 13g34.4 Receiver Parameters . 13g34.4.1 Applicability . 13g34.4.2 Blocking 13g34.4.2.1 Description 13g3ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)4 4.4.2.2 Limits 13g34.4.2.3 Conformance . 13g35 Technical Requirements for Uni-Directional Co

15、mmunication 13g35.1 Mode A Applicability and Conformance Requirements 13g35.2 Communication method . 13g35.3 Transmitter Parameters . 14g35.4 Receiver Parameters . 14g35.4.1 Applicability . 14g35.4.2 Adjacent Channel Selectivity 14g35.4.2.1 Description 14g35.4.2.2 Limits 14g35.4.2.3 Conformance . 14

16、g35.4.3 Blocking 14g35.4.3.1 Description 14g35.4.3.2 Limits 14g35.4.3.3 Conformance . 14g35.4.4 Adjacent Channel Saturation 14g35.4.4.1 Description 14g35.4.4.2 Limits 14g35.4.4.3 Conformance . 15g35.4.5 Spurious Response Rejection 15g35.4.5.1 Description 15g35.4.5.2 Limits 15g35.4.5.3 Conformance .

17、15g35.4.6 Behaviour at high wanted signal level 15g35.4.6.1 Description 15g35.4.6.2 Limits 15g35.4.6.3 Conformance . 15g36 Bi-Directional Communication - Single Frequency . 15g36.1 Mode B1 Applicability and Conformance Requirements. 15g36.2 Bi-directional Communication . 16g36.2.1 Applicability . 16

18、g36.2.2 Acknowledgement 16g36.2.2.1 Description 16g36.2.2.2 Limits 16g36.2.2.3 Conformance . 16g36.3 Transmitter Parameters . 16g36.4 Receiver Parameters . 16g36.4.1 Applicability . 16g36.4.2 Adjacent Channel Selectivity 16g36.4.2.1 Description 16g36.4.2.2 Limits 16g36.4.2.3 Conformance . 16g36.4.3

19、Blocking 17g36.4.3.1 Description 17g36.4.3.2 Limits 17g36.4.3.3 Conformance . 17g36.4.4 Adjacent Channel Saturation 17g36.4.4.1 Description 17g36.4.4.2 Limits 17g36.4.4.3 Conformance . 17g36.4.5 Spurious Response Rejection 17g36.4.5.1 Description 17g36.4.5.2 Limits 17g36.4.5.3 Conformance . 18g36.4.

20、6 Behaviour at high wanted signal level 18g36.4.6.1 Description 18g36.4.6.2 Limits 18g36.4.6.3 Conformance . 18g37 Testing for compliance with technical requirements 18g3ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)5 7.1 General . 18g37.2 Presentation of equipment for testing purposes 18g37.3 Wanted per

21、formance criteria 19g37.3.1 Receiver response . 19g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 20g3Annex B (informative): Selection of technical parameters . 22g3B.1 Introduction 22g3B.2 Receiver sensitivity 22g3B.3 Other r

22、eceiver parameters 22g3B.4 Listen before talk 22g3Annex C (informative): Bibliography . 23g3History 24g3ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining t

23、o these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. L

24、atest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETS

25、I Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commiss

26、ions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/

27、5/EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corr

28、esponding essential requirements of that Directive and associated EFTA regulations. The present document is part 3-1 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 01 August 2016 Date of latest announ

29、cement of this EN (doa): 30 November 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 May 2017 Date of withdrawal of any conflicting National Standard (dow): 31 May 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “sho

30、uld not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI E

31、N 300 220-3-1 V2.1.1 (2016-12)7 Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio equipment within the scope of the Radio Equipment Directive (RED) i.2. The equipment to which the present document applie

32、s fall within the low duty cycle high reliability devices category. NOTE 1: The low duty cycle/high reliability devices category is defined in Commission Decision 2013/752/EU i.3 as: “Category of short-range devices“ means a group of short- range devices that use spectrum with similar technical spec

33、trum access mechanisms or based on common usage scenarios. and The low duty cycle/high reliability device category covers radio devices that rely on low overall spectrum utilisation and low duty cycle spectrum access rules to ensure highly reliable spectrum access and transmissions in shared bands.

34、Typical uses include alarm systems that use radio communication for indicating an alert condition at a distant location and social alarms systems that allow reliable communication for a person in distress. It is recognized that the radio communications link alone does not determine the overall opera

35、tion of a system, but that a functioning radio communications link is an essential foundation upon which a system may be built. The present document sets out various means and features by which the performance of a radio communications link may be improved. These include: 1) Spectrum Access Rules -

36、with the aim of reducing the probability of collisions between transmissions from different equipment. 2) Receiver Parameters - with the aim of reducing the probability of interference from equipment on other frequencies. 3) Bi-Directional Communications - with the aim of reducing the time and numbe

37、r of transmissions required to achieve a given level of confidence in successful communication. Application of these features, separately or in combination, does not necessarily ensure successful radio communication. In addition, there are other features that may be considered, such as listen before

38、 talk or error correction, that may improve overall performance. Clauses 1 and 3 provide a general description on the types of equipment covered by the present document and the definitions and abbreviations used. Clause 4 specifies technical requirements to be met by all equipment. Clause 5 specifie

39、s technical requirements for receivers in equipment with uni-directional communications. Clause 6 specifies technical requirements for equipment with bi-directional communications. Clause 7 specifies the methods for testing for compliance with the technical requirements. Annex A summarizes the requi

40、rements relevant to the RE-Directive i.2. ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)8 1 Scope The present document applies to social alarm devices operating on designated frequencies. Designated frequencies are those frequency bands identified in Commission Decision 2013/752/EU i.3 as having a usage

41、available only to social alarms. Social alarms are defined in Commission Decision 2013/752/EU i.3 as: “Social alarm devices“ are radio communications systems that allow reliable communication for a person in distress in a confined area to initiate a call for assistance. Typical uses of social alarm

42、are to assist elderly or disabled people. These radio equipment types are capable of operating, for transmission or reception, in all or part of the frequency bands given in table 1. Table 1: Frequency bands Frequency band 869,200 MHz to 869,250 MHz The present document contains requirements to demo

43、nstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific

44、. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.or

45、g/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 220-1 (V3.1.1) (11-2016): “Short Range D

46、evices (SRD) operating in the frequency range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific refere

47、nces, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following

48、 referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI EG 203 336: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the product

49、ion of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. ETSI ETSI EN 300 220-3-1 V2.1.1 (2016-12)9 i.2 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC (RE-Directive). i.3 Commission Decision 2013/752/EU amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 200