ENV 12694-1997 en Public Transport - Road Vehicles - Dimensional Requirements for Variable Electronic External Signs《公共运输 道路车辆 可变外部电子的尺寸要求》.pdf

《ENV 12694-1997 en Public Transport - Road Vehicles - Dimensional Requirements for Variable Electronic External Signs《公共运输 道路车辆 可变外部电子的尺寸要求》.pdf》由会员分享，可在线阅读，更多相关《ENV 12694-1997 en Public Transport - Road Vehicles - Dimensional Requirements for Variable Electronic External Signs《公共运输 道路车辆 可变外部电子的尺寸要求》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、DRAFT FOR DEVELOPMENT DD ENV 12694:1997 Public transport Road vehicles Dimensional requirements for variable electronic external signs ICS 35.240.60DDENV 12694:1997 This Draft for Development, having been prepared under the direction of the Electrotechnical Sector Board, was published under the auth

2、ority of the Standards Board and comes into effect on 15 September 1997 BSI 04-1999 ISBN 0 580 28447 6 National foreword This publication is not to be regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature because the lev

3、el of innovation on the subject is currently high. It should be applied on this provisional basis, so that information and experience of its practical application may be obtained. Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the E

4、uropean organization responsible for its conversion into a European Standard. A review of this publication will be initiated2 years after its publication by the European organization so that a decision can be taken on its status at the end of its three-year life. The commencement of the review perio

5、d will be notified by an announcement in Update Standards. According to the replies received by the end of the review period, the responsible BSI Committee will decide whether to support the conversion into a European Standard, to extend the life of the prestandard or to withdraw it. Comments should

6、 be sent in writing to the Secretary of BSI Technical Committee EPL/278, Road transport informatics, at389 Chiswick High Road, London W44AL, giving the document reference and clause number and proposing, where possible, an appropriate revision of the text. Cross-references Attention is drawn to the

7、fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications The British Standards which implement international or European publications referred to in this document may be found in the BS

8、I Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theENV title page, pages 2 to 5 a

9、nd abackcover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsDDENV12694:1997 BSI 04-1999 i Contents Page National forewor

10、d Inside front cover Foreword 2 Text of ENV 12694 3ii blankEUROPEAN PRESTANDARD PRNORME EUROPENNE EUROPISCHE VORNORM ENV 12694 June 1997 ICS 35.240.60; 43.080.20; 45.060.01 Descriptors: Road vehicles, passenger transport, public utilities, information, teleprocessing, display, signs, definitions, sp

11、ecifications, position (location), dimensions, characteristics English version Public transport Road vehicles Dimensional requirements for variable electronic external signs This European Prestandard (ENV) was approved by CEN on 1997-05-28 as a prospective standard for provisional application. The p

12、eriod of validity of this ENV is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the ENV can be converted into an European Standard (EN). CEN members are required to announce the existance of this E

13、NV in the same way as for an EN and to make the ENV available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the ENV) until the final decision about the possible conversion of the ENV into an EN is reached. CEN mem

14、bers are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normali

15、sation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN ALL rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. ENV 12694:1997 EENV12694:1997 BSI 04-1999 2 Foreword This European Prestandard has bee

16、n prepared by Technical Committee CEN/TC 278 “Road transport and traffic telematics”, the secretariat of which is held by NNI. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this European Prestandard: Austria,

17、Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom. Contents Page Foreword 2 1 Scope 3 2 Definitions 3 3 Requirements 3 3.1 Location and display characteristics and c

18、ontent 3 3.1.1 Headsigns 3 3.1.2 Sidesigns 3 3.1.3 Rearsigns 4 3.2 Characters 4 3.2.1 Generalities 4 3.2.2 Colours 4 3.2.3 Classes of characters 4 3.2.4 Recommendations 4 3.3 Dimensions 5 3.4 Electric connections 5 3.5 Sign illumination and mounting 5ENV12694:1997 BSI 04-1999 3 1 Scope This standard

19、 refers to variable external signs (mechanical signs without electronic control excluded), when installed in public transport vehicles such as: buses, trams, trolley-buses (undergrounds and railway vehicles are excluded), and specifies location, dimensions, display characteristics, contents of infor

20、mation and wiring. At the present time there exists a set of technologies for such signs (ex: dot matrix, flaps, films, LCD, etc.). 2 Definitions For the purposes of the present standards the following definitions will apply: variable external sign device fitted on urban and long distance public tra

21、nsport vehicles which informs the users about the details of operation of that particular vehicle destination information variable information visible from outside the vehicle which displays details of the operation of that vehicle such as: line identification, destination, route taken, terminus or

22、any possible variation to the above related to the operation of the vehicle headsign a sign displaying all or part of destination information and located at the front of the vehicle sidesign a sign displaying all or part of destination information and located at the side of the vehicle rearsign a si

23、gn displaying all or part of destination information and located at the rear of the vehicle on board transmission bus a set of wires connecting together the different on board AVMS equipments for powering and data transmission, and the associated transmission protocols A.V.M.S. (Automatic Vehicle Mo

24、nitoring System) system equipment on board the vehicle of urban and interurban public transportation (buses and tramways, excluding transportation in complete individual sites such as trains) and the corresponding equipments installed on the ground, that are designed for the operation of public tran

25、sportation (operation aid systems, automatic information systems, fare collection systems, maintenance aid systems) 3 Requirements The sign surface shall be positioned vertically to the roadway or marginally tilted downwards. The aim of the standards shall not be to define the individual technologie

26、s. However every system shall guarantee good visibility and ease of reading, also in adverse weather conditions such as fog, snow, strong sun light, etc. These signs shall respect a set of given conditions, in order to be compatible with the characteristics of the vehicle, to allow some interchangea

27、bility and to be functionally efficient. 3.1 Location and display characteristics and content 3.1.1 Headsign The headsign shall be located above the windscreen or on the upper part of it. It is strongly recommended that looking from the ground the line number shall be on the left and the destination

28、 on the right. If there is only the line number it is strongly recommended that the sign shall be placed in the centre or on the left as seen from the ground. 3.1.2 Sidesign The sign shall be located near the first entrance door or above the door. The line identification shall be on the left of the

29、sign, as seen from the ground. In positioning the sign, regulations concerning headroom above seats, if any, shall be complied with.ENV12694:1997 4 BSI 04-1999 3.1.3 Rearsign As seen from outside the vehicle, the sign shall be located in the centre or the right (left for U.K.), on the rear upper par

30、t of the vehicle. It displays at least the line identification. 3.2 Characters 3.2.1 Generalities For legibility purposes, the character type (letters and numbers), shall be as close as possible to Helvetica. It is recommended to use a reduced number of characters and to avoid alternating messages.

31、Information can be displayed on one or more character lines. It is recommended that a mixture of upper and lower case letters shall be used. 3.2.2 Colours Yellow or white on a black background are recommended. However other colours can be used for particular needs, taking into account that the lumin

32、ous green and red, corresponding to standards for traffic lights and emergency colours, should be avoided. 3.2.3 Classes of character heights (expressed in capital letters): 3.2.4 Recommendations It is recommended that the character heights chosen conform to the following tables: CLASS A = 70mm. CLA

33、SS B = 100mm. CLASS C = 125mm. CLASS D = 150mm. CLASS E = 180mm. CLASS F = 200mm. CLASS G = 240mm. CLASS H = $ 300mm. MINI-BUSES A B C D E F G H Headsign line identification X X X X X Headsign destination single line text X X Headsign destination multiline text X Sidesign line identification X X X X

34、 X Sidesign destination single line text X X X Sidesign destination multiline text X Rearsign line identification X X X X NORMAL BUSES A B C D E F G H Headsign line identification X X X X Headsign destination single line text X X X X Headsign destination multiline text X X X Sidesign line identifica

35、tion X X X X X X Sidesign destination single line text X X X Sidesign destination multiline text X X X Rearsign line identification X X X XENV12694:1997 BSI 04-1999 5 3.3 Dimensions When the sign is integral to the body of the vehicle, the volumetric dimensions required for the space to accomodate t

36、hese classifications of characters without restricting the technologies used shall be comprised between the following figures: In order to allow maximum flexibility, in the choice of the sign it is recommended that Body Manufacturers provide the largest space possible subject to the above mentionned

37、 specifications. 3.4 Electric connections When a European standard exists for an on board transmission bus for road public transport vehicles and is implemented in the vehicle, then the sign shall be either directly connected to this bus or connected to this bus through a special control unit. 3.5 S

38、ign illumination and mounting The displays shall be easy to install, substitute and maintain. The substitution of the lights should not entail the disassembling, even partial, of the signs. The lighting system shall not illuminate the external glass in front of the sign but only the surface of the s

39、ign. The viewing windows shall be of the same dimensions or bigger than the destination sign to provide an easier reading. It is recommended to leave a space of50mm.between the sign and the sides to permit easy installation and maintenance (working space). Mini-bus front space dimensions: minimum 1

40、000mm length 200mm height 130mm depth maximum 1 500mm length 350mm height 220mm depth Normal bus front space dimensions: minimum 1 700mm length 340mm height 150mm depth maximum 2 200mm length 450mm height 250mm depth Mini-bus side space dimensions: minimum 700mm length 200mm height 100mm depth maxim

41、um 1 000mm length 350mm height 150mm depth Normal bus side space dimensions: minimum 1 100mm length 220mm height 120mm depth maximum 1 820mm length 350mm height 200mm depth Mini-bus rear space dimensions: minimum 400mm length 200mm height 130mm depth maximum 500mm length 350mm height 220mm depth Nor

42、mal bus rear space dimensions: minimum 450mm length 220mm height 120mm depth maximum 650mm length 450mm height 250mm depthBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

43、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internati

44、onal level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We wo

45、uld be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual upd

46、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orde

47、rs for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Librar

48、y and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards dev

49、elopments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or o