EN ISO 26987-2012 en Resilient floor coverings - Determination of staining and resistance to chemicals《弹性地面覆盖物 染色和抗化学药剂性的测定》.pdf

《EN ISO 26987-2012 en Resilient floor coverings - Determination of staining and resistance to chemicals《弹性地面覆盖物 染色和抗化学药剂性的测定》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 26987-2012 en Resilient floor coverings - Determination of staining and resistance to chemicals《弹性地面覆盖物 染色和抗化学药剂性的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 26987:2012Resilient floor coverings Determination of staining andresistance to chemicals (ISO26987:2008)BS EN ISO 26987:2012 BRITISH STANDARDNational forewordThis Briti

2、sh Standard is the UK implementation of EN ISO26987:2012. It is identical to . It supersedes BS EN 423:2002 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/60, Resilient floor coverings.A list of organizations represented on this committee can beobta

3、ined on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 75244 5ICS 97.150Compliance with a B

4、ritish Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 29 February 2012.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 26987 F

5、ebruary 2012 ICS 97.150 Supersedes EN 423:2001English Version Resilient floor coverings - Determination of staining and resistance to chemicals (ISO 26987:2008) Revtements de sol rsilients - Dtermination de la rsistance au tachage et aux produits chimiques (ISO 26987:2008) Elastische Bodenbelge - Be

6、stimmung der Fleckenempfindlichkeit und Chemikalienbestndigkeit (ISO 26987:2008) This European Standard was approved by CEN on 24 December 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

7、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A

8、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cypr

9、us, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZ

10、ATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 26987:2012: EBS EN ISO 26987:2012EN ISO 26987:2012 (E

11、) 3 Foreword The text of ISO 26987:2008 has been prepared by Technical Committee ISO/TC 219 “Floor coverings” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 26987:2012 by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” t

12、he secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2012, and conflicting national standards shall be withdrawn at the latest by August 2012. Attention i

13、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 423:2001. According to the CEN/CENELEC Internal Regulations, the nati

14、onal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

15、 Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 26987:2008 has been approved by CEN as a EN ISO 26987:2012 without any modification. BS EN ISO 26987:2012ISO 26987:2008(E) ISO 2008 All rights reserve

16、d iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bodyinterested in a subject for which

17、 a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closelywith the International Electrotechnical Com mission (IEC) on all matt

18、ers of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft Internationa l Standardsadopted by the technical committees are circula

19、ted to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsibl

20、e for identifying an y or all such patent rights. ISO 26987 was prepared by Technical Committee ISO/TC 219, Floor coverings. BS EN ISO 26987:2012BS EN ISO 26987:2012INTERNATIONAL STANDA RD ISO 26987:2008(E) ISO 2008 All rights reserved 1Resilient floor coverings Determination of staining and resista

21、nce to chemicals1 Scope This International Standard specifies a procedure for the determination of the reaction of resilient floorcovering to chemical substances. 2 Principle Various chemical substances in liquid or paste form are placed on a test piece for defined periods and thenremoved. After cle

22、aning has been carried out, the resulting change of appearance is assessed under specifiedlighting conditions.3 Apparatus and materials 3.1 Standard laboratoryequipment. 3.1.1 Pipettes.3.1.2 Watchglass, diameter 40 mm.3.1.3 Spatulas. 3.2 Chemical substances in liquid or paste form. This Internationa

23、l Standard does not specify or suggest the chemical substances to be tested. 3.3Standard cleaning and stain removal products. 3.3.1 White cotton, in pad or cloth form. 3.3.2 Brushes, hard, unlikely to score the surface. 3.3.3 Warm water, used alone or with selected cleaning products (see Annex A). 3

24、.4 Abrasivematerials (abrasives, abrasive scouring pads, steel wool No. 00 or scouring powder, orabrasive papers, grain size P 240 or finer, used withwater).3.5Special cleaning products,recommended by the floor covering manufacturer.3.6 Illumination device , comprising a lamp of correlated colour te

25、mperature 5 500 K to 6500 K, mountedto give an intensityof light at the viewing platform of (1 500 100) lx and in such away as to illuminate thetest piece vertically from above. The surroundings shall be neutral and darkened. The intensity of the light shall be checked frequentlybythe use of a luxom

26、eter. The lifetime of the lamp, asgiven by the manufacturer, shall not be exceeded. BS EN ISO 26987:2012ISO 26987:2008(E)2 ISO 2008 All rights reserved3.7Rotary viewing table, which enables the testpiece to be rotated so that it can be viewed from alldirections under the standard illumination. 4 Sam

27、pling and preparation of test piece Take a representative sample from the available floor covering material. The sample should be obtained froma new roll or carton and should not have been treated with any floor finish/polish.Take one test piece in each colour to be testedwith a surface area of at l

28、east 3 000 mm2 , for each of thechemical substances to be tested. If the test uses a chemical substance likely to cause swelling ordeformation of the test piece, e.g. prolonged contact with the solvent, bond the test piece to a fibre-cementboard at least 5 days before testing. Identify the test piec

29、es corresponding to each of the substances tested, either bymarking numbers on the testpiece (using a marking which is not affec ted by the material used in the test),or b y a sketch, diagram orphotograph. 5 Atmosphere for conditioning and testing Condition the test pieces at a temperature of (23 2)

30、 C and a relative humidity of(50 5) % for a minimumof 24 h. Maintain this condition when carrying out the test. 6 Test procedure 6.1Application of liquid substances 6.1.1 Using a clean pipette(3.1.1), pour a small quantityof the liquid chemical substance to test (see 3.2) into the centre of the mark

31、ed position of the testpiece. Apply the convex face of a watch glass (3.1.2) to the liquidand remove it immediately. If the diameter of the splash of the liquid chemical substance is more than 15 mm,apply the watch glass again. Leave it in position this time, in such a way as to produce a splash of

32、liquidchemical substance covering an area of 300 mm2 to 400 mm2 . 6.1.2 If the diameter of the chemical substance does not exceed 15 mm, add a few more drops and spreadit again by applying the watch glass. Leave it in position this time, in such a way as to produce a splash of the liquid chemical su

33、bstance of 300 mm2 to 400 mm2 . 6.2Application of paste substances With a spatula (3.1.3), spread about 1 000 mm3 of the paste chemical substance to test (see 3.2) over an areaof 300 mm2 to 400 mm2 (i.e. thickness 2,5 mm to 3 mm). 6.3Duration of contactThe main duration of contact shall be 2 h with

34、the evaluation of the sample being done within 5 min ofremoving the chemical substance. After cleaning and observationif the test piece has been adversely affected (staining, dulling, softening, swelling, etc.),a new test shall be conducted for a period of 30 min. 6.4Cleaning and observation 6.4.1 B

35、efore cleaning, remove chemical substances which are still liquid with cotton (3.3.1),working fromthe edge towards the centre of the stain. Scrape off the remains of paste with a spatula (3.1.3) and wipe withcotton as above. Clean the surface, working from the edge toward the centreof the stain, usi

36、ng one or moreBS EN ISO 26987:2012ISO 26987:2008(E) ISO 2008 All rights reserved 3cleaning and stain removal products as described in 3.3. See alsoAnnex A. After cleaning has been carriedout, examine the residual staining using the illumination device (3.6) from a distance of approximately 800 mmat

37、an approximate angle of 45 degrees and from all dire ctions by slowly rotating the viewing table (3.7).6.4.2 If a stain is still visible, rub it down with anabrasive material (see 3.4) or a cleaning product recommended by the manufacturer (3.5), and examine it as described in 6.4.1. 7 Expression of

38、resultsAfter observing the testpieces as described in 6.4, assign an index to each of the testpieces, accordi ng to the observed effect of the testafter cleaning/abrasion, as shown in Table 1. Table 1 Interpretation and presentation ofresultsIndex Effect of test after cleaning/abrasion 0 Not affecte

39、d1 Slight 2 Moderate 3 Severe 8 Test reportThe test report shall contain the following information:a) a statement that the tests were performed in accordance with this Inte rnational Standard (ISO 26987); b) complete identification of the floor covering tested, including type, source, colour and man

40、ufacturersreference numbers;c) history of the sample, i.e. from what source was the sample s ecured, new carton or roll manufacturedwhen;d) the chemical substances, type of cleaning and stain removal products and abrasive materials used andthe contact periods; e) the test results in accordance with

41、Table 1;f) anydeviation from this International Standard which mayhave affected the results.BS EN ISO 26987:2012ISO 26987:2008(E)4 ISO 2008 All rights reservedAnnex A(informative) Examples of cleaning and stain removal products Synthetic detergent, e.g. sodium alkysulfate SoapAlkaline products, e.g.

42、 washing soda or ammonia solution (5 %)Hydrogen peroxide Sodium hypochlorite Sodium thiosulfate, 1 % solutionOxalic acidDenatured ethanol White spirit Turpentine BS EN ISO 26987:2012ISO 26987:2008(E) ISO 2008 All rights reserved 5Bibliography1 EN 423, Resilient floor coveri ngs Determination of resi

43、stance t o staining2 ASTM F925, Standard Test Method for Resist ance to Chemicals of Resilient Flooring3 JIS A 1454, Test methods Resilient floorcoverings. Staining Test, Section 6.12This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible fo

44、r preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards L

45、imited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the l

46、atest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can

47、 be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of Britis

48、h Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed

49、 to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)