EN ISO 20029-1-2018 en Plastics - Thermoplastic polyester ester and polyether ester elastomers for moulding and extrusion - Part 1 Designation system and basis for specification.pdf

《EN ISO 20029-1-2018 en Plastics - Thermoplastic polyester ester and polyether ester elastomers for moulding and extrusion - Part 1 Designation system and basis for specification.pdf》由会员分享，可在线阅读，更多相关《EN ISO 20029-1-2018 en Plastics - Thermoplastic polyester ester and polyether ester elastomers for moulding and extrusion - Part 1 Designation system and basis for specification.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusionPart 1: Designation system and basis for specificationBS EN ISO 200291:2018National forewordThis British Standard is the

2、UK implementation of EN ISO 200291:2018. It is identical to ISO 200291:2017. It supersedes BS EN ISO 149101:2013, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can

3、be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 87271 6ICS 83.080.20Complia

4、nce with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 200291:2018E

5、UROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 20029-1February 2018ICS 83.080.20 Supersedes EN ISO 149101:2013EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN

6、ISO 200291:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersPlastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 1: Designation system and basis for specification (ISO 200291:2017)Plastiques las

7、tomres thermoplastiques base de polyester/ester et polyther/ester pour moulage et extrusion Partie 1: Systme de dsignation et base de spcifications (ISO 20029-1:2017)Kunststoffe Thermoplastische Polyester/Ester und Polyether/EsterElastomerWerkstoffe Teil 1: Bezeichnungssystem und Basis fr Spezifikat

8、ionen (ISO 20029-1:2017)This European Standard was approved by CEN on 28 November 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists a

9、nd bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the r

10、esponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav

11、Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN ISO 20029-1:2018 (E)European for

12、ewordThis document (EN ISO 200291:2018) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.This European Standard shall be given the status of a national standard, either by publication

13、 of an identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall be withdrawn at the latest by August 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held respon

14、sible for identifying any or all such patent rights.This document supersedes EN ISO 149101:2013.According to the CENCENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus

15、, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

16、United Kingdom.Endorsement noticeThe text of ISO 200291:2017 has been approved by CEN as EN ISO 200291:2018 without any modification.2BS EN ISO 200291:2018ISO 20029-1:2017(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Designation system 24.1 General . 24.

17、2 Data block 1 . 24.3 Data block 2 . 34.4 Data block 3 . 44.5 Data block 4 . 44.5.1 General 44.5.2 Hardness . 44.5.3 Melting temperature . 54.5.4 Tensile/flexural modulus of elasticity . 54.6 Data block 5 . 65 Examples of designations 6Annex A (informative) Definition of thermoplastic polyester/este

18、r and polyether/estercopolymer elastomers 9Bibliography .11 ISO 2017 All rights reserved iiiContents PageBS EN ISO 200291:2018ISO 20029-1:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pr

19、eparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and nongovernmental, in

20、 liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC

21、 Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility th

22、at some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent d

23、eclarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformit

24、y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermopla

25、stic materials.This first edition of ISO 20029-1 cancels and replaces ISO 14910-1:2013, which has been technically revised to introduce a new designation system.The revised designation system is published under a new ISO number, as many existing documents refer to ISO 149101. If the existing ISO 149

26、101 would be replaced by the new designation system, these documents would refer to the incorrect designation system.In order to give users time to switch from ISO 149101 to ISO 200291, any designation system according to ISO 149101 is to be phased out in 5 to 10 years.A list of all parts in the ISO

27、 20029 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 200291:2018ISO 20029-1:2017(E)IntroductionISO 14910-1:2013 is complex and does not fit with daily practice anymore. In practice, ISO 18064 and ISO 11469 are, in combination, “improperly” being used as a designatio

28、n system for, e.g. marking. The aim of this document is to simplify the data block system and to connect more to ISO 18064 and ISO 11469, where the first two blocks are used for generic identification and marking of products. ISO 2017 All rights reserved vBS EN ISO 200291:2018This page deliberately

29、left blankPlastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 1: Designation system and basis for specification1 ScopeThis document establishes a system of designation for thermoplastic polyester/ester and polyether/ester elastomers, which may be u

30、sed as the basis for specifications.The types of thermoplastic polyester/ester and polyether/ester elastomer are differentiated from each other by a classification system based on appropriate levels of the designatory properties:a) hardness;b) melting temperature;c) tensile/flexural modulus of elast

31、icity;and on information about the intended application and/or method of processing, important properties, additives, colour, fillers and reinforcing materials.This document is applicable to all thermoplastic polyester/ester and polyether/ester elastomers. It applies to materials ready for normal us

32、e in the form of powder, granules or pellets, unmodified or modified by colourants, fillers or other additives.It is not intended to imply that materials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on pr

33、ocessing conditions which may be required to specify a material. If such additional properties are required, they are intended to be determined in accordance with the test methods specified in ISO 20029-2, if suitable.In order to designate a thermoplastic polyester/ester or polyether/ester elastomer

34、 to meet particular specifications, the requirements are given in data block 5 (see 4.1).2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited a

35、pplies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 10434, Plastics Symbols and abbreviated terms Part 4: Flame retardantsISO 18064, Thermoplastic elastomers Nomenclature and abbreviated termsISO 200292, Plastics Thermoplastic polyeste

36、r/ester and polyether/ester elastomers for moulding and extrusion Part 2: Preparation of test specimens and determination of properties3 Terms and definitionsNo terms and definitions are listed in this document.INTERNATIONAL STANDARD ISO 20029-1:2017(E) ISO 2017 All rights reserved 1BS EN ISO 200291

37、:2018ISO 20029-1:2017(E)ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp4 Designation system4.1 GeneralThe designation syste

38、m for thermoplastics is based on the following standardized pattern.DesignationIdentity blockDescription block (optional)International Standard number blockIndividualitem blockData block 1 Data block 2 Data block 3 Data block 4 Data block 5The designation consists of an optional description block, r

39、eading “Thermoplastics”, and an identity block comprising the International Standard number and an individualitem block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Identification of the plastic by its

40、 abbreviated term (TPC), in accordance with ISO 18064, and information about the composition of the polymer (see 4.2). Data block 2: fillers or reinforcing materials and their nominal content; flame retardant; optionally recyclate and its content (see 4.3). Data block 3: Position 1: Intended applica

41、tion and/or method of processing (see 4.4). Positions 2 to 8: Important properties, additives and supplementary information (see 4.4). Data block 4: Designatory properties (see 4.5). Data block 5: For the purpose of specifications, a fifth data block contains appropriate information (see 4.6).The fi

42、rst character of the individual item block shall be a hyphen. The five data blocks shall be separated from each other by a comma. If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,). Terminal commas may be omitted.NOTE Data blocks 1 and 2 toge

43、ther form the part marking symbol.4.2 Data block 1In this data block, after the hyphen, the thermoplastic elastomer is identified by its abbreviated term in accordance with ISO 18064 and, after a space, a symbol indicating the composition as specified in Table 1.Table 1 Symbols indicating the chemic

44、al structure of thermoplastic polyester/ester and polyether/ester elastomers in data block 1Symbol Chemical identificationTPCES Polyester soft segmentTPCET Polyether soft segment2 ISO 2017 All rights reservedBS EN ISO 200291:2018ISO 20029-1:2017(E)Symbol Chemical identificationTPCEA Alkane soft segm

45、entTPCXY Not definedThe prefix TP is followed by a letter representing the category of the thermoplastic elastomer, as given in ISO 18064. For copolyester thermoplastic elastomers, the prefix TP is followed by the letter C.Copolyester thermoplastic elastomers consist of a block copolymer of alternat

46、ing hard segments and soft segments, the chemical linkages in the main chain being ester and/or ether. The “TPC” group is subcategorized into groups according to the linkages in the soft blocks (see Annex A).4.3 Data block 2In this data block, the type of filler and/or reinforcing material is repres

47、ented by a single code-letter in position 1 and its physical form by a second code-letter in position 2, the code-letters being as specified in Table 2. Subsequently (without a space), the actual content may be given by a two-figure code-number in positions 3 and 4.Mixtures of materials and/or forms

48、 may be indicated by combining the relevant codes using the sign “+” and placing the whole between parentheses followed by the total filler content. For example, a mixture of 25 % (by mass) of glass fibre (GF) and 10 % (by mass) of mineral powder (MD) would be indicated by (GF25+MD10) or (GF+MD)35.T

49、able 2 Code-letters used for fillers and reinforcing materials in data block 2Code-letter Material (Position 1)Form (Position 2)BC D F G H K M S T X Z BoronCarbonaGlassCalcium carbonate (CaCO3)Minerala; metalbOrganica; syntheticTalcNot specifiedOthersaBalls; beads; spheresPowder; dry blendFibreGranules; groundWhiskersNot specifiedOthersaThese materials may be further defined after position 4 of the data block, e.g. by chemical symbol or by additional codes to be agreed upon.bM