EN ISO 16410-1-2017 en Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3 - Part 1 Test suite structure and test purposes.pdf

《EN ISO 16410-1-2017 en Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3 - Part 1 Test suite structure and test purposes.pdf》由会员分享，可在线阅读，更多相关《EN ISO 16410-1-2017 en Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3 - Part 1 Test suite structure and test purposes.pdf（172页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3Part 1: Test suite structure and test purposesBS EN ISO 164101:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 16410-1 Decemb

2、er 2017 ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 16410-1:2011English Version Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3 - Part 1: Test suite structure and test purposes (ISO 16410-1:2017) Perception du tlpage - valuation de la conformit de lquipement lISO

3、 17575-3 - Partie 1: Structure de la suite dessais et objectifs des essais (ISO 16410-1:2017) Elektronische Gebhrenerhebung - Konformittsbeurteilung von Gerten nach ISO/TS 17575-3 - Teil 1: Struktur und Zweck des Prfprogramms (ISO 16410-1:2017) This European Standard was approved by CEN on 12 Decemb

4、er 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obta

5、ined on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CE

6、N-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland

7、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Managemen

8、t Centre: Rue de la Science 23, B-1040 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 16410-1:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 164101:2017. It is identical to ISO 16

9、4101:2017. It supersedes DD CEN ISO/TS 164101:2011, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/278, Intelligent transport systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publicatio

10、n does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 95985 1ICS 03.220.20; 35.240.60Compliance with a British Standard cannot confer im

11、munity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 164101:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NO

12、RM EN ISO 16410-1 December 2017 ICS 03.220.20; 35.240.60 Supersedes CEN ISO/TS 16410-1:2011English Version Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3 - Part 1: Test suite structure and test purposes (ISO 16410-1:2017) Perception du tlpage - valuation de la conf

13、ormit de lquipement lISO 17575-3 - Partie 1: Structure de la suite dessais et objectifs des essais (ISO 16410-1:2017) Elektronische Gebhrenerhebung - Konformittsbeurteilung von Gerten nach ISO/TS 17575-3 - Teil 1: Struktur und Zweck des Prfprogramms (ISO 16410-1:2017) This European Standard was appr

14、oved by CEN on 12 December 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation

15、al standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own languag

16、e and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, H

17、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMU

18、NG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 16410-1:2017 EBS EN ISO 164101:2017EN ISO 16410-1:2017 (E) 3 European foreword This document (EN ISO 1

19、6410-1:2017) has been prepared by Technical Committee ISO/TC 204 “Intelligent transport systems” in collaboration with Technical Committee CEN/TC 278 “Intelligent transport systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, eith

20、er by publication of an identical text or by endorsement, at the latest by June 2018 and conflicting national standards shall be withdrawn at the latest by June 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not b

21、e held responsible for identifying any or all such patent rights. This document supersedes CEN ISO/TS 16410-1:2011. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association. According to the CEN-CENELEC Internal Regulations, the

22、national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

23、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 16410-1:2017 has been approved by CEN as EN ISO 16410-1:2017 without any modification. BS EN ISO 16

24、4101:2017ISO 16410-1:2017(E)Foreword ivIntroduction vi1 Scope . 12 Normative references 23 Terms and definitions . 24 Abbreviated terms 45 Test suite structure 55.1 Structure . 55.2 Reference to conformance test specifications 65.3 Test purposes (TP) 65.3.1 TP definition conventions 65.3.2 TP naming

25、 conventions 75.4 Conformance test report 8Annex A (normative) Test purposes (TP) for Front End 9Annex B (normative) Test purposes (TP) for Back End .96Annex C (normative) Data structures . 133Annex D (normative) PCTR for Front End 154Annex E (normative) PCTR for Back End 159Bibliography . 163 ISO 2

26、017 All rights reserved iiiContents PageBS EN ISO 164101:2017ISO 16410-1:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through I

27、SO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates

28、closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criter

29、ia needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of p

30、atent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name us

31、ed in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the

32、 World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The document was prepared by Technical Committee ISO/TC 204, Intelligent transport systems.This first edition of ISO 16410-1 cancels and replaces the first edition

33、 of ISO/TS 16410-1:2011, which has been technically revised. The following changes have been made: this document has been converted from a Technical Specification to an International Standard; amendments have been made to reflect changes to the underlying base standards, especially ISO 17575 (all pa

34、rts); major changes have been made regarding: data element changes introduced by ISO 17575-1 and ISO 17575-3; new test purposes related to: protocol version handling; toll context partitions; fee calculation algorithm; rounding rules; alternative currency; test purposes related to the following have

35、 been removed: communications services;iv ISO 2017 All rights reservedBS EN ISO 164101:2017ISO 16410-1:2017(E) rules with respect to support of context data which are no longer required by ISO 17575-3; the terms and definitions have been revised; editorial and formal corrections, as well as changes

36、to improve readability, have been made. ISO 2017 All rights reserved vBS EN ISO 164101:2017ISO 16410-1:2017(E)IntroductionThis document is part of a series of standards that supports interoperability of autonomous EFC-systems. Autonomous systems use satellite positioning, often combined with additio

37、nal sensor technologies such as gyroscopes, odometers and accelerometers, to localize the vehicle and to find its position on a map containing the charged geographic objects, such as charged roads or charged areas. From the charged objects, the vehicle characteristics, the time of day and other data

38、 that are relevant for describing road use, the tariff and ultimately, the road usage fee is determined.Autonomous on-board equipment (OBE) operates without relying on dedicated road-side infrastructure by employing wide-area technologies such as global navigation satellite systems (GNSS) and cellul

39、ar communications networks (CN). Therefore, autonomous systems may also be referred to as GNSS/CN systems.Within the series of EFC standards, this document defines tests for conformity evaluation of Front End and Back End that comply with the requirements towards the context data specified in ISO 17

40、575-3.This document is based on ISO 17575-3, and the ISO 9646 series on conformance test methodology.vi ISO 2017 All rights reservedBS EN ISO 164101:2017INTERNATIONAL STANDARD ISO 16410-1:2017(E)Electronic fee collection Evaluation of equipment for conformity to ISO 17575-3 Part 1: Test suite struct

41、ure and test purposes1 ScopeThe ISO 16410 series provides a suite of tests in order to assess compliance of the Front End and Back End behaviours in relation to the requirements in ISO 17575-3. This document contains the definition of such tests in the form of test purposes, listing the required ini

42、tial conditions, references and individual steps in a structured textual manner. ISO 16410-2 contains the identical tests written in testing and test control notation version 3 (TTCN v3).The test purposes defined in this document reflect the structural and semantic requirements stated in ISO 17575-3

43、. Presence/absence of particular data elements (see ISO 17575-3:2016, 8.5.5); Semantics related to various data elements, e.g.: Activation of context data and handling multiple contexts (see ISO 17575-3:2016, 8.3); Handling the precedence and priority levels (see ISO 17575-3:2016, 8.5.2 to 8.5.4); U

44、niqueness of relevant data elements (see ISO 17575-3:2016, 8.5.2 to 8.5.4); Correct definition of the charge objects (see ISO 17575-3:2016, 8.5.4); Fee calculation algorithm (see ISO 17575-3:2016, 8.5.3.7); Security (see ISO 17575-3:2016, 7.2).With regard to the individual data sets and EFC attribut

45、es defined in ISO 17575-3, the test purposes have been organized into the test suite groups, designated for the Front End and Back End respectively.In addition to the test purposes, this document also provides proforma conformance test report templates for both the Front End and Back End test purpos

46、es and an informative statement on the usage of this document for the European electronic toll service (EETS).For more information regarding the requirements against which the conformance is evaluated in this document, refer to ISO 17575-3.Testing of the following behaviours and functionalities is o

47、utside the scope of this document: dynamic behaviour, i.e. sequence of messages and triggering events that must be exchanged/happen to fulfil certain charging scenarios; profiles and business logic built on top of particular pricing schemas; behaviour invalid of Front End and Back End, BI test purpo

48、ses are not applicable for any test purpose group (as ISO 17575-3 does not specify behaviour invalid). ISO 2017 All rights reserved 1BS EN ISO 164101:2017ISO 16410-1:2017(E)2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content const

49、itutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 17575-1, Electronic fee collection Application interface definition for autonomous systems Part 1: ChargingISO 17575-3:2016, Electronic fee collection Application interface definition for autonomous systems Part 3: Context data3 Terms and definitionsFor the purposes of this docume