EN ISO 15614-7-2007 6912 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 7 Overlay welding《金属材料焊接程序的规范和鉴定 焊接程序试验 第7部分 覆.pdf

《EN ISO 15614-7-2007 6912 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 7 Overlay welding《金属材料焊接程序的规范和鉴定 焊接程序试验 第7部分 覆.pdf》由会员分享，可在线阅读，更多相关《EN ISO 15614-7-2007 6912 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 7 Overlay welding《金属材料焊接程序的规范和鉴定 焊接程序试验 第7部分 覆.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHSg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g

2、48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58-,-,-materials Welding procedure test Part 7: Overlay weldingThe European Standard EN ISO 15614-7:2007 has the status of a British StandardICS 25.160.10Specification and qualification of welding procedures for metallic BRITISH STANDARD

3、BS EN ISO 15614-7:2007BS EN ISO 15614-7:2007Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHSThis British Standard was published under the authority of the Standards Policy and Strateg

4、y Committee on 31 July 2007 BSI 2007ISBN 978 0 580 54476 7-,-,-Amendments issued since publicationAmd. No. Date CommentsCompliance with a British Standard cannot confer immunity from legal obligations.National forewordThis British Standard is the UK implementation of EN ISO 15614-7:2007.The UK parti

5、cipation in its preparation was entrusted to Technical Committee WEE/36, Qualification of welding personnel and welding procedures.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisio

6、ns of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 15614-7June 2007ICS 25.160.10English VersionSpecification and qualification of welding procedures for metallicmaterials - Welding procedure test - Part 7: Overlay welding(ISO 156

7、14-7:2007)Descriptif et qualification dun mode opratoire de soudagepour les matriaux mtalliques - preuve de qualificationdun mode opratoire de soudage - Partie 7: Rechargementpar soudage (ISO 15614-7:2007)Anforderungen und Qualifizierung von Schweiverfahrenfr metallische Werkstoffe - Schweiverfahren

8、sprfung -Teil 7: Auftragschweien (ISO 15614-7:2007)This European Standard was approved by CEN on 21 May 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alterat

9、ion. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translat

10、ionunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Gree

11、ce, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Ce

12、ntre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15614-7:2007: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or

13、 networking permitted without license from IHS-,-,-Foreword This document (EN ISO 15614-7:2007) has been prepared by Technical Committee CEN/TC 121 “Welding“, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44 “Welding and allied processes“. This European St

14、andard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2007, and conflicting national standards shall be withdrawn at the latest by December 2007. This document has been prepared under a mandate given to CEN by

15、 the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national stand

16、ards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po

17、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN ISO 15614-7:2007Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Reference numberISO 15614-7

18、:2007(E)INTERNATIONAL STANDARD ISO15614-7First edition2007-06-15Specification and qualification of welding procedures for metallic materials Welding procedure test Part 7: Overlay welding Descriptif et qualification dun mode opratoire de soudage pour les matriaux mtalliques preuve de qualification d

19、un mode opratoire de soudage Partie 7: Rechargement par soudage EN ISO 15614-7:2007Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ii Copyright European Committee for Standardiza

20、tion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Preliminary welding procedure specification (pWPS) 2 4.1 Overl

21、ay welding 2 4.2 Hardfacing . 2 4.3 Building-up 3 4.4 Buttering 3 5 Welding procedure test 3 6 Test piece 3 6.1 Shape and dimensions of test pieces. 3 6.2 Welding of test pieces 5 7 Examination and testing 6 7.1 Extent of testing 6 7.2 Non-destructive testing (NDT). 6 7.3 Location and taking of test

22、 specimens 6 7.4 Destructive testing 8 7.5 Acceptance criteria. 10 7.6 Retesting 11 8 Range of qualification 11 8.1 General. 11 8.2 Qualification related to the manufacturer 11 8.3 Qualification related to the material 12 8.4 Qualification related to the filler material/overlay . 13 8.5 Common to we

23、lding procedures. 14 8.6 Specific to welding processes 15 9 Welding procedure qualification record (WPQR) 17 Annex A (informative) Welding procedure qualification record form (WPQR) 18 Bibliography . 21 EN ISO 15614-7:2007Annex ZA (informative) Relationship between this International Standard and th

24、e EssentialRequirements of EU Directive 97/23/EC . 22 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-iv Foreword ISO (the International Organization for Standardization) is a wo

25、rldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented o

26、n that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted

27、 in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standa

28、rd requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15614-7 was prepared b

29、y the European Committee for Standardization (CEN) Technical Committee CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical

30、cooperation between ISO and CEN (Vienna Agreement). ISO 15614 consists of the following parts, under the general title Specification and qualification of welding procedures for metallic materials Welding procedure test: Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloy

31、s Part 2: Arc welding of aluminium and its alloys Part 3: Fusion and pressure welding of non-alloyed and low-alloyed cast irons Part 4: Finishing welding of aluminium castings Part 5: Arc welding of titanium, zirconium and their alloys Part 6: Arc and gas welding of copper and its alloys Part 7: Ove

32、rlay welding Part 8: Welding of tubes to tube-plate joints Part 10: Hyperbaric dry welding Part 11: Electron and laser beam welding Part 12: Spot, seam and projection welding Part 13: Resistance butt and flash welding Requests for official interpretations of any aspect of this part of ISO 15614 shou

33、ld be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete listing of these bodies can be found at www.iso.org. EN ISO 15614-7:2007Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking

34、 permitted without license from IHS-,-,-vIntroduction This part of ISO 15614 is part of a series of standards. Details of this series are given in ISO 15607:2003, Annex A. Previous procedure qualifications to former national standards or specifications should be taken into consideration at the time

35、of the enquiry or contract stage and agreed between the contracting parties. EN ISO 15614-7:2007Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-blankCopyright European Committee

36、for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1Specification and qualification of welding procedures for metallic materials Welding procedure test Part 7: Overlay welding 1 Scope This part of ISO 15614 spe

37、cifies how a preliminary welding procedure specification for overlay welding is qualified by welding procedure tests. This part of ISO 15614 defines the conditions for carrying out welding procedure tests and the range of qualification for welding procedures for all practical welding operations with

38、in the range of variables listed in Clause 8. Additional tests may be required by application standards. This part of ISO 15614 applies to all welding processes suitable for overlay welding. This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous

39、welding procedure tests made to former national standards or specifications. Where additional tests are carried out to make the qualification technically equivalent, they are only done on a test piece made in accordance with this part of ISO 15614. This part of ISO 15614 does not apply to overlay we

40、lding where cracks are intentionally produced (e.g. special hardfacing applications). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references the latest edition of t

41、he referenced document (including any amendments) applies. ISO 3452, Non destructive testing Penetrant inspection General principles ISO 5173, Destructive tests on welds in metallic materials Bend tests ISO 6947, Welds Working positions Definitions of angles of slope and rotation ISO 9015-1, Destruc

42、tive tests on welds in metallic materials Hardness testing Part 1: Hardness test on arc welded joints ISO 14174, Welding consumables Fluxes for submerged arc welding Classification ISO 14175, Welding consumables Shielding gases for arc welding and cutting ISO/TR 15608, Welding Guidelines for a metal

43、lic materials grouping system EN ISO 15614-7:2007Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 ISO 15609-1, Specification and qualification of welding procedures for metallic

44、 materials Welding procedure specification Part 1: Arc welding ISO 15609-2, Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding ISO 15609-3, Specification and qualification of welding procedures for metallic materials Weldi

45、ng procedure specification Part 3: Electron beam welding ISO 15609-4, Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding ISO 15613, Specification and qualification of welding procedures for metallic materials Qualif

46、ication based on pre-production welding test ISO 15614-1, Specification and qualification of welding procedures for metallic materials Welding procedure test Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys ISO 17637, Non-destructive testing of welds Visual testing o

47、f fusion-welded joints ISO 17639, Destructive tests on welds in metallic materials Macroscopic and microscopic examination of welds ISO 17640, Non-destructive testing of welds Ultrasonic testing of welded joints ISO/TR 259011), Welding and related processes Vocabulary 3 Terms and definitions For the

48、 purposes of this document, the terms and definitions given in ISO/TR 25901 apply. 4 Preliminary welding procedure specification (pWPS) 4.1 Overlay welding The pWPS shall be in accordance with ISO 15609-1, ISO 15609-3 and ISO 15609-4. It shall specify the tolerances for all the relevant parameters. The welding procedure shall be qualified in accordance with Clauses 5 to 8. 4.2 Hardfacing The pWPS shall be in accordance with ISO 15609-1, ISO 15609-2, ISO 15