EN ISO 14273-2001 3218 Specimen Dimensions and Procedure for Shear Testing Resistance Spot Seam and Embossed Projection Welds《电阻点焊 缝焊和浮凸焊接的焊接点剪切试验的试样尺寸和程序 ISO 14273-2000》.pdf

《EN ISO 14273-2001 3218 Specimen Dimensions and Procedure for Shear Testing Resistance Spot Seam and Embossed Projection Welds《电阻点焊 缝焊和浮凸焊接的焊接点剪切试验的试样尺寸和程序 ISO 14273-2000》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 14273-2001 3218 Specimen Dimensions and Procedure for Shear Testing Resistance Spot Seam and Embossed Projection Welds《电阻点焊 缝焊和浮凸焊接的焊接点剪切试验的试样尺寸和程序 ISO 14273-2000》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds The European Standard EN IS0 14273:2001 has the status ofa British Standard ICs 25.160.40 BS EN IS0 14273:2001 Incorporating Corrigendum No. I Wk present to the responsible intern

2、ational/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to it

3、s secretary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the

4、BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summa

5、ry of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, pages ii and iii, a blank page, pages 1 to 8, the Annex ZA page and a back cover. The BSI copyright date displayed in this document indicates when the docume

6、nt was last issued. This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on O8 November 2001 Amendments issued since publication O BSI 8 March 2002 Cop

7、yright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 14273 October 2001 ICs 25.160.40 English version Specimen dimensions and pro

8、cedure for shear testing resistance spot, seam and embossed projection welds (IS0 14273:2000) Dimensions des prouvettes et mode opratoire pour lessai de cisaillement des soudures par rsistance par points, la molette et par bossages (IS0 14273:2000) Probenmae und Durchfhrung fr die Scherzugprfung an

9、Widerstandspunkt-, Naht- und Buckelschweiungen mit geprgten Buckeln (IS0 14273:2000) This European Standard was approved by CEN on 3 October 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

10、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in

11、any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germa

12、ny, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All ri

13、ghts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 14273:2001 E Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0

14、 14273:2001 I CORRECTED 2002-01-02 I Foreword The text of the International Standard from Technical Committee IIW has been taken over as a European Standard by Technical Committee CEN/TC 121 “Welding“, the secretariat of which is held by DS. This European Standard shall be given the status of a nati

15、onal standard, either by publication of an identical text or by endorsement, at the latest by April 2002, and conflicting national standards shall be withdrawn at the latest by April 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countri

16、es are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Stand

17、ard IS0 14273:2000 has been approved by CEN as a European Standard without any modifications. NOTE Normative references to International Standards are listed in annex ZA (normative). Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction

18、or networking permitted without license from IHS-,-,-EN IS0 14273:2001 INTERNATIONAL STANDARD IS0 14273 First edition 2000-1 1-01 Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds Dimensions des prouveffes ef mode oprafoire pour lessai de cisaill

19、emenf des soudures par rsisfance par poinfs, la moleffe ef par bossages Reference number IS0 14273:2000(E) Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 II Co

20、pyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards

21、bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizat

22、ions, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in th

23、e ISOAEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that s

24、ome of the elements of this International Standard may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 14273 was prepared in collaboration with the International Institute of Welding, which has been approved

25、 by the IS0 Council as an international standardizing body in the field of welding. . 111 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 Copyright European Com

26、mittee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds 1 Scope This International Sta

27、ndard specifies specimen dimensions and a testing procedure for shear testing of spot, seam and embossed projection welds, in overlapping sheets, in any metallic material of thickness 0,5 mm to 10 mm, where the welds have a maximum diameter of 7dt (where t is the sheet thickness in mm). With welds o

28、f diameter 5dt and G 7dt, the value of shear strength can be underestimated when using the recommended test specimen dimensions. The object of shear testing is to determine the shear force that the test specimen can sustain. 2 Normative reference The following normative document contains provisions

29、which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the

30、possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 7500-1 , Mefallic maferials

31、 - Verificafion of sfafic uniaxial fesfing machines - Parf 1: Tensionlcompression fesfing machines - Verificafion and calibrafion of fhe force-measuring sysfem. 3 Terms and definitions For the purposes of this International Standard, the following terms and definitions apply. 3.1 shear force maximum

32、 force obtained from the test 3.2 plug diameter (plug failure) mean diameter of the plug dP See Figure 1 a). 3.3 weld diameter d (partial plug failure) mean diameter of the fused zone measured at the interface omitting the corona bond area and the maximum diameter of the plug component of the failur

33、e See Figure 1 a). NOTE Measurement of the minimum diameter of the plug component should be quoted separately. 1 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001

34、 3.4 weld diameter d (interface failure) mean diameter of the fused zone measured at the interface, omitting the corona bond area See Figure 1 b). Key 1 Symmetrical 2 Asymmetrical 3 Partial a d = d, = (dl + d2)/2 d = (dl + d2)/2 and d, = (d2 + d3)/2 a) Weld with plug (slug) failure 2 Copyright Europ

35、ean Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 Key 1 Sheared nugget 2 Corona bond zone 3 Nugget a Diameter of the corona. Diameter of the nugget. b) Weld with interface failu

36、re, d I ,4, shim plates shall be used for clamping the test specimen in the grips of the tensile testing machine. The shim plate shall be as thick as the sheet of the test specimen as shown in Figure 4. Testing shall be carried out at room temperature. 5 Copyright European Committee for Standardizat

37、ion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 i i i -1- i i I I t a) Profile without shim plates 1 t b) Profile with shim plates Key 1 Shim plate Figure 4 - Shear test configuration 6 Testreport The test

38、 report shall contain the following information: a) the welding process; b) the welding conditions and equipment; c) the material and its condition; d) the dimensions of the test piece and of the test specimen; e) f) the type of failure; individual values, mean value and standard deviation of the sh

39、ear force in kilonewtons; g) h) special remarks if any. individual values, mean value and standard deviation of the weld diameter; A load-elongation curve shall be drawn in order to give information on the deformation of the test specimen. Examples are shown in Figure 5. 6 Copyright European Committ

40、ee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 u- o 10 m 1 5,o O O 2 4 6 Elongation, rnrn a) Spot welded joints made on 1 mm thick steel sheet z Y u- m O 1 12.5 10,o 7,s 5,o 2.5 O O 1 2

41、 3 4 Elongation, rnrn b) Spot welded joints made on 1,25 mm thick steel sheet Figure 5 - Typical load-elongation curves for the shear test 7 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license fr

42、om IHS-,-,-EN IS0 14273:2001 Bibliograph y I IS0 14329), Welding - Desfrucfive fesfing of welds - Failure types and geomefric measuremenfs for resisfance spof, seam and projecfion welds. 1) To be published. 8 Copyright European Committee for Standardization Provided by IHS under license with CENNot

43、for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN IS0 14273:2001 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorporates by dated or undated reference, provisions from other

44、publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of -any of these publications apply to this European Standard only when incorporated in it by amendment or r

45、evision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE Where an International Publication has been modified by common modifications, indicated by (mod.), the relevant EN/HD applies. Publication Yearm - EN Year IS0 7500-1 1999 Metallic m

46、aterials - Verification of EN IS0 7500-1 1999 static uniaxial testing machines - Part 1 : Tension/compression testing machines Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS

47、EN IS0 14273:2001 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated

48、 by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscri