EN ISO 13916-1996 en Welding - Guidance on the Measurement of Preheating Temperature Interpass Temperature and Preheat Maintenance Temperature《焊接 预热温度 道间温度和预热维持温度测量的指南 ISO 13916-19.pdf

《EN ISO 13916-1996 en Welding - Guidance on the Measurement of Preheating Temperature Interpass Temperature and Preheat Maintenance Temperature《焊接 预热温度 道间温度和预热维持温度测量的指南 ISO 13916-19.pdf》由会员分享，可在线阅读，更多相关《EN ISO 13916-1996 en Welding - Guidance on the Measurement of Preheating Temperature Interpass Temperature and Preheat Maintenance Temperature《焊接 预热温度 道间温度和预热维持温度测量的指南 ISO 13916-19.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 SD.BSI BS EN IS0 L3Lb-NGL 1977 Lb24bb9 0579449 5Lb m BRITISH STANDARD Welding - Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature The European Standard EN IS0 13916 1996 has the status of a British Standard ICs 25.160 NO COPYING WITHOUT

2、 BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN IS0 13916 : 1997 BS EN IS0 13916 : 1997 The foilowing BSI references relate to the work on this standard Committee reference WEE47 Draft for comment 93i716854 DC ISBN O 680 26366 X This British Standard, having been prepared under the cirect

3、ion of the Engineering Sector BOgi.d, was published under the authority of the Standards Board and comes into effect on I5 January 1997 O BSI 1997 Committees responsible for this British Standard The prepamtion of this British standard was entrusted to Technical Committee wEW17, Metai-arc welding of

4、 steel, upon which the following bodies were represented British Constructional Steelwork Association Ltd. British Iron and steel Producers Association British Nuclear Fuels plc Electricity Association Institution of stsuctural Engineers Power Generation Contractom Association (PGCA (BEAMA Ltd.) Rai

5、lway Industry Mion Weldmg institute Weldmg Manufacturers? Association (BEAMA Ltd) Amendments issued since publication I Te* affected STD-BSI BS EN ISL371b-ENGL 1977 m Lb24bb7 0579451 174 m BS EN IS0 13916 : 1997 Contents Committees responsible National foreword page Inside front cover ii Foreword Te

6、xt of EN IS0 13916 2 3 * * v, O BSI 1997 i STD-BSI BS EN IS0 L39Lb-ENGL 1997 W 1b2qbb9 0579q52 O00 W BS EN IS0 13916 : 1997 National foreword This British Standard has been prepared by Technical Committee WW17 and is the English language version of EN IS0 13916 : 1996 Widding - Gu.idame on ule measu

7、rement of preheating tempemture, interpass temperature and preheat mintenume temperuture published by the European Committee for Standardization (CEN). It is identical with IS0 13916 : 1996 published by the International Organization for StandarMon (ISO). EN IS0 13916 was produced as the result of i

8、nternational discussion in which the UK took an active part. It has been assumed in the drafting of this British Standard that the execution of its provisions is entrusted to appropriately qualified and experienced people. Compliance with a British Standard does not of itself confer immunity from le

9、gal obligations. O BSI 1997 STD.BSI BS EN IS0 L39Lb-ENGL 1997 m Lb24bbS 0579453 T47 m EUROPEAN STANDARD NORME EUROPENNE EUROP- NORM EN Is0 13916 August 1996 ICs 25.160.00 Descriptors: Welding, fusion welding, workpieces, heat affected zone, temperature, temperature measurements English version Weldi

10、ng - Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature (IS0 13916 : 1996) Soudage - Lignes directrices pour le mesurage de la temprature de prchauffage, de la temprature entre passes et de la temprature de maintien du prchauffage (IS0 13

11、916 : 1996) SchweiBen - Anleitung zur Messung der Vorwrm-, Zwischlenlagen- und Haltetemperatw: (IS0 13916 : 1996) This European Standard was approved by CEN on 199GO-20. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipuiate the conditions for giving this European S

12、tandard the status of a national standard without any alteration. Uptodate lists and bibiiographical references concerning such national standards may be obtained on application to the Centrai Secretariat or to any CEN member. This European Standard exists in three official versions (English, French

13、, German). A version in any other language made by translation under the responsibility of a CEN member inh its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the nationai standards bodies of Austria, Belgium, Denmark, Finland, Fran

14、ce, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fur Normung Centrai Secretariat: rue de Stassart 36, B-1060 Brussels O

15、 1996 Copyright reserved to CEN members Ref. No. EN IS0 13916 : 1996 E Page 2 EN IS0 13916 : 1996 Content Page Foreword . 3 1 Scope 4 2 Definitions 4 2.1 Preheating temperature (lp) 4 2.2 Interpass temperature (Ti) 4 2.3 Preheat maintenance temperature (1, ) . 4 3 Requirements . 4 3.1 Point of measu

16、rement . 4 3.2 lime of measurement 5 3.3 Test equipment . 6 4 Test report 6 5 Designation . 6 STD.BS1 BS ENISO L3Lb-ENGL 1777 D Lb2qbbS 0579Li55 ALT D Page 3 EN IS0 13916 : 1396 Foreword The text of EN IS0 1391 6:1996 has been prepared by Technical Committee CEN/TC 121 “Welding“, the secretariat of

17、which is held by DS, in collaboration with Technical Committee ISO/TC 44 “Welding and allied processes“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 1997, and conflicting national sta

18、ndards shall be withdrawn at the latest by February 1997. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, It

19、aly, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. - STD-BSI BS EN IS0 L37Lb-ENGL 1977 m LbZLibb7 057745b 75b Page 4 EN IS0 13916 : 1996 1 Scope This standard specifies requirements for the measurement of preheating tempera- ture, interpass temperature

20、 and preheat maintenance temperature for fusion welding. This standard may also be applied as appropriate in the case of other welding processes. This standard does not cover the measurement of post weld heat treatment temperatures . 2 Definitions For the purposes of this standard the following defi

21、nitions apply: 2.1 preheating temperature (Tp): the temperature of the workpiece in the weld zone imnediately prior to any welding operation. It Is normally expressed as a minimum and is usually equal to the minimum interpass temperature. 2.2 interpass temperature (Ti): the temperature in a multi-ru

22、n weld and adjacent parent metal imnediately prior to the application of the next run. It is normally expressed as a maximum temperature. 2.3 preheat maintenance temperature(Tm): the minimum temperature in the weld zone which shall be maintained if welding is interrupted. 3 Requirements 3.1 Point of

23、 measurement The temperature measurement shall normally be made on the surface of the work- piece facing the welder, at a distance of A = 4 x t, but not more than 50 mn, from the longitudinal edge of the groove (see figure i). This shall apply for workpieces thickness t not exceeding 50 mn in the we

24、ld. When the thickness exceeds 50 mn, the required temperature shall exist in the parent metal for a distance of at least 75 mn or as otherwise agreed In any di- rection from the joint preparation. Where practicable, the temperature shall be measured on the face opposite to that being heated. Otherw

25、ise, the temperature shall be confirmed on the heated face at a time after removal of the heat source related to parent metal thickness to allow for temperature equalization. Where fixed permanent heaters are in use and there is no access to the reverse face for temperature measurement, readings sha

26、ll be taken on the exposed parent metal surface imnediately adjacent to the weld preparation. The time allowed for the temperature equalization shall be of the order of 2 min for each 25 mn of parent metal thickness. Interpass temperature shall be measured on the weld metal or the imnediately adjace

27、nt parent metal. STD-BSI BS EN IS0 1371b-ENGL 1777 W lb24bb7 0577457 b92 Page 5 EN IS0 13916 : 1996 Dimensions in mn a) butt joint * * v) b) flllet joint t S 50: A = 4 x t, MX. 50 t 50: A = 75 Figure 1 - Distance between points of measurement 3.2 Time of measurement Interpass temperature shall be me

28、asured in the weld area imnediately before passage of the arc. If the preheat maintenance temperature is specified it shall be monitored uring the period of welding interruption. STD-BSI BS EN IS0 137Lb-ENGL 1777 m Lb2ibbS 0577458 527 m Page 6 EN IS0 13916 : 1996 3.3 Test equipment Equlpment used fo

29、r temperature measurement should be specified in the welding procedure specifications, e.g.: - temperature sensitive materials (e.g. crayons or paints) (TS); - contact thermometer (CT); - thermocouple (TE); - optical or electrical devices for contactless measurement (TB). 4 Test report If a test rep

30、ort is required, it shall refer to this standard and give the fol- lowing minimum information in accordance with the speclfication in welding procedure specification: - measured preheating temperature, in OC; - measured Interpass temperature, in OC; - measured preheat maintenance temperature, in OC;

31、 - any deviation from this standard, if applicable. 5 Designation Examples of designation, which should be used in test reports 5.1 Example 1 A preheating temperature Tp measured only once in accordance with this standard as 155 OC (Tp 155) using a contact thermometer (CT) shall be designated as fol

32、 lows: Temperature EN IS0 13916 - Tp 155 - CT 5.2 Example 2 An interpass temperature Ti measured more than once in accordance with thls standard as 130 oc, 153 OC and 160 OC (Ti 130/160) using a thermocouple (TE) shall be designated as follows: Temperature EN IS0 13916 - Ti 130/160 - TE STD. BSI BS

33、EN IS0 L39Lb-ENGL BS EN IS0 13916 : 1997 BSI 389 Chiswick High Road London w4 4AL 1997 Lb24bb 0579459 4b5 BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internaiionai leve

34、l. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include ail the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users o

35、f British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quaiity of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British Standard would inform the Secrem of th

36、e responsible technical committee, the identity of which can be found on the inside front cover. Tel 0181 996 9ooo; Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatidly receive the latest editions of standards. Buying standards

37、Orders for ail BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tel 0181 996 7000, Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have b

38、een published as British Standards, uniess otherwise requested Information on standards BSI provides a wide range of information on national, European and international stanards through its Libmy, the Standardline Database, the BSI Jnfodon Technology Service (BITS) and its khnicai Help to Exporters

39、Service. Contact the Information Department at Chiswick Tel: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Se

40、rvices, Membership at Chiswick Tel 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright., in the UK, of the publications of the international staneon bodies. Except as permitted under the Copynght, Designs and Patents Act 1988 no extra

41、ct may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission hm BSI. This does not preclude the free use, in the come of implementing the standard, of necessary details such as symb

42、ols, and size, type or grae designahons. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If pennission is granted, the tem may include royaty payments or a licensing agreement. Details and advice can be obtained from the Copynght Manager, BSI, 389 Chiswick High Road, London W4 4AL ISBN O 680 26356 X WEE717