EN ISO 12690-2010 en Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities《金属和其他无机镀层 热喷涂协作 任务和职责》.pdf

《EN ISO 12690-2010 en Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities《金属和其他无机镀层 热喷涂协作 任务和职责》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 12690-2010 en Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities《金属和其他无机镀层 热喷涂协作 任务和职责》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 12690:2010Metallic and other inorganiccoatings Thermal spraycoordination Tasksand responsibilities (ISO12690:2010)BS EN ISO 12690:2010 BRITISH STANDARDNational foreword

2、This British Standard is the UK implementation of EN ISO12690:2010. It supersedes BS EN 13214:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee STI/33, Electrodeposited and related coatings.A list of organizations represented on this committee can be

3、obtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 66319 2ICS 25.220.20Compliance with a British Standard cannot confer immunity fromlegal obligations.Th

4、is British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 12690 December 2010 ICS 25.220.20 Supersedes EN 13214:2001English Versi

5、on Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities (ISO 12690:2010) Revtements mtalliques et autres revtements inorganiques - Coordination en projection thermique - Tches et responsabilits (ISO 12690:2010) Metallische und andere anorganische berzge - A

6、ufsicht fr das thermische Spritzen - Aufgaben und Verantwortung (ISO 12690:2010) This European Standard was approved by CEN on 14 December 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

7、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A

8、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cypr

9、us, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION CO

10、MIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 12690:2010: EBS EN ISO 12690:2010EN ISO 12690:2010 (E) 3 Fore

11、word This document (EN ISO 12690:2010) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 107 “Metallic and other inorganic coatings”. This European Standard

12、shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2011, and conflicting national standards shall be withdrawn at the latest by June 2011. Attention is drawn to the possibility that some of the elements of this docume

13、nt may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13214:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound

14、 to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sw

15、eden, Switzerland and the United Kingdom. BS EN ISO 12690:2010ISO 12690:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Tasks and responsibilities .2 4.1 Quality-related activities.2 4.2 Definition of task

16、s and responsibilities 3 5 Job description3 5.1 General .3 5.2 Tasks.3 5.3 Responsibility3 6 Technical knowledge 4 6.1 General knowledge requirements of all spraying coordination personnel.4 6.2 Specific knowledge requirements of responsible spraying coordination personnel 4 Annex A (informative) Re

17、commendations of technical knowledge.5 Annex B (normative) Essential thermal-spraying-related tasks in accordance with ISO 14922 to be considered when appropriate 6 Bibliography11 BS EN ISO 12690:2010ISO 12690:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for St

18、andardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the rig

19、ht to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International

20、 Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as a

21、n International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO

22、12690 was prepared by the European Committee for Standardization (CEN) Technical Committee TC 240, Thermal spraying and thermally sprayed coatings, in collaboration with ISO Technical Committee ISO/TC 107, Metallic and other inorganic coatings in accordance with the Agreement on technical cooperatio

23、n between ISO and CEN (Vienna Agreement). BS EN ISO 12690:2010ISO 12690:2010(E) ISO 2010 All rights reserved vIntroduction Thermal spraying is a special process which requires qualified personnel for execution of thermal spraying operations on components or parts. This provides confidence in thermal

24、 spraying fabrication and allows reliable performance to be achieved in service during operational time. Coordination personnel are able to coordinate all activities related to thermal spraying, and are responsible for planning, executing, supervising and inspecting. BS EN ISO 12690:2010BS EN ISO 12

25、690:2010INTERNATIONAL STANDARD ISO 12690:2010(E) ISO 2010 All rights reserved 1Metallic and other inorganic coatings Thermal spray coordination Tasks and responsibilities 1 Scope This International Standard specifies the tasks and responsibilities necessary to ensure the quality of a thermal sprayed

26、 coating or a coated component, including the coordination of activities related to thermal spraying. Thermal spraying coordination can be carried out by one or a number of persons within the same company or manufacturing department. The responsibilities of the spraying coordinator are specified by

27、the manufacturer. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6507

28、-1, Metallic materials Vickers hardness test Part 1: Test method ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) ISO 14918, Thermal spraying Approval testing of thermal sprayers ISO 14922-1, Thermal spraying Quality requirements of t

29、hermally sprayed structures Part 1: Guidance for selection and use ISO 14922-2, Thermal spraying Quality requirements of thermally sprayed structures Part 2: Comprehensive quality requirements ISO 14922-3, Thermal spraying Quality requirements of thermally sprayed structures Part 3: Standard quality

30、 requirements ISO 14922-4, Thermal spraying Quality requirements of thermally sprayed structures Part 4: Elementary quality requirements ISO 14923, Thermal spraying Characterization and testing of thermally sprayed coatings EN 473, Non-destructive testing Qualification and certification of NDT perso

31、nnel General principles EN 571-1, Non-destructive testing Penetrant testing Part 1: General principles EN 582, Thermal spraying Determination of tensile adhesive strength EN 657:2005, Thermal spraying Terminology, classification BS EN ISO 12690:2010ISO 12690:2010(E) 2 ISO 2010 All rights reservedEN

32、1395-1, Thermal spraying Acceptance inspection for thermal spraying equipment Part 1: General requirements EN 1395-2, Thermal spraying Acceptance inspection for thermal spraying equipment Part 2: Flame spraying including HVOF EN 1395-3, Thermal spraying Acceptance inspection for thermal spraying equ

33、ipment Part 3: Arc spraying EN 1395-4, Thermal spraying Acceptance inspection for thermal spraying equipment Part 4: Plasma spraying EN 1395-5, Thermal spraying Acceptance inspection for thermal spraying equipment Part 5: Plasma spraying in chambers EN 1395-6, Thermal spraying Acceptance inspection

34、for thermal spraying equipment Part 6: Manipulator systems EN 1395-7, Thermal spraying Acceptance inspection for thermal spraying equipment Part 7: Powder feed systems EN 15311, Thermal spraying Components with thermally sprayed coatings Technical supply conditions EN 15340, Thermal spraying Determi

35、nation of shear load resistance of thermally sprayed coatings EN 15648, Thermal spraying Component related procedure qualification 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 657:2005 and the following apply. 3.1 manufacturing department thermal s

36、praying workshops or sites under the same technical and quality management 3.2 thermal spraying coordinator person who has responsibilities in the manufacturing organization for thermal spraying and thermal-spraying-related activities, whose competence and knowledge has been demonstrated by, for exa

37、mple, education, training and/or relevant manufacturing experience 3.3 thermal spraying inspection inspecting of all activities related to thermal spraying, testing and measuring the thermal sprayed coatings to be manufactured, and thereby influencing components or parts to meet the requirements def

38、ined by the contractors coating specification or by the responsible technical department of the manufacturer NOTE Thermal spraying inspection is part of spraying coordination. 4 Tasks and responsibilities 4.1 Quality-related activities Annex B shall be used to allocate quality-related tasks and resp

39、onsibilities to thermal spraying coordination personnel within the company or manufacturing department practising thermal spraying fabrication. Annex B BS EN ISO 12690:2010ISO 12690:2010(E) ISO 2010 All rights reserved 3may be supplemented for special applications. Not all items will necessarily app

40、ly to all manufacturing organizations or quality system or are necessary. Therefore, an application-related selection should be made. 4.2 Definition of tasks and responsibilities Each single activity in Annex B may be associated with a number of tasks and responsibilities, such as: preparation of th

41、e spray procedure specification; control; inspection, checking or witnessing; to ensure that international and national laws and regulations concerning protection of the operators health and the environment are followed, and the safety requirements for thermal spraying equipment according to the EN

42、15339 series are fulfilled as far as they belong to the duties of the user. All relevant tasks and responsibilities shall be defined and allocated for all relevant items. If thermal spraying coordination is carried out by a number of persons, the tasks, responsibilities and activities shall be speci

43、fied and allocated for each thermal spraying coordinator in the organization. The manufacturer shall appoint at least one spraying coordinator. Thermal spraying coordination is the sole responsibility of the manufacturer. The spraying coordination may be subcontracted, however, compliance to this In

44、ternational Standard remains the responsibility of the manufacturer. 5 Job description 5.1 General If a job description for the thermal spraying coordinator is required by the quality management system of the manufacturer, contract or specified application standard, it shall include the tasks and re

45、sponsibilities of the coordinator. 5.2 Tasks For identification of the assigned tasks, see 4.2 and Annex B. 5.3 Responsibility For identification of the assigned responsibility, consider the following: position in the manufacturing department and responsibility; the extent of authorization to accept

46、 by signing on behalf of the manufacturing department, for example, procedure specifications, supervision reports, etc., as needed in order to fulfil their assigned tasks; the extent of authorization to carry out the assigned tasks. BS EN ISO 12690:2010ISO 12690:2010(E) 4 ISO 2010 All rights reserve

47、d6 Technical knowledge 6.1 General knowledge requirements of all spraying coordination personnel For all tasks assigned, a thermal spraying coordinator shall be able to demonstrate adequate technical knowledge that enables him to perform such tasks in a satisfactory way. The following factors should

48、 be considered: general technical knowledge; specialized technical knowledge. This may be attained by a combination of theoretical knowledge, training and/or experience. The extent of required manufacturing experience, education and technical knowledge shall be described by the manufacturing departm

49、ent and will depend on the assigned tasks and responsibilities. 6.2 Specific knowledge requirements of responsible spraying coordination personnel 6.2.1 General Responsible thermal spraying coordinators shall be allocated from one of the groups described in 6.2.2 to 6.2.4. This will depend on the nature, complexity of the production and the requirements concerning the component. 6.2.2 Comprehensive technical knowledge Thermal spraying coordinati