EN ISO 11963-2012 en Plastics - Polycarbonate sheets - Types dimensions and characteristics《塑料-聚碳酸酯表类型 尺寸和特征》.pdf

《EN ISO 11963-2012 en Plastics - Polycarbonate sheets - Types dimensions and characteristics《塑料-聚碳酸酯表类型 尺寸和特征》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 11963-2012 en Plastics - Polycarbonate sheets - Types dimensions and characteristics《塑料-聚碳酸酯表类型 尺寸和特征》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11963:2012Plastics Polycarbonatesheets Types, dimensionsand characteristics (ISO11963:2012)BS EN ISO 11963:2012 BRITISH STANDARDNational forewordThis British Standard i

2、s the UK implementation of EN ISO11963:2012. It supersedes BS EN ISO 11963:1996 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/75, Plastics and rubber film and sheets.A list of organizations represented on this committee can beobtained on request t

3、o its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 73193 8ICS 83.140.10Compliance with a British Standar

4、d cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11963 November 2012 I

5、CS 83.140.10 Supersedes EN ISO 11963:1995English Version Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:2012) Plastiques - Plaques en polycarbonate - Types, dimensions et caractristiques (ISO 11963:2012) Kunststoffe - Tafeln aus Polycarbonat - Lieferformen, Abmess

6、ungen und charakteristische Eigenschaften (ISO 11963:2012) This European Standard was approved by CEN on 14 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard with

7、out any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other

8、language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, De

9、nmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITT

10、EE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11963:2012: EBS EN ISO 11963:2012EN

11、ISO 11963:2012 (E) 3 Foreword This document (EN ISO 11963:2012) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standa

12、rd, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/

13、or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 11963:1995. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austri

14、a, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

15、 Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11963:2012 has been approved by CEN as a EN ISO 11963:2012 without any modification. BS EN ISO 11963:2012ISO 11963:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Comp

16、osition 24 Requirements 24.1 Masking . 24.2 Appearance 24.3 Colour 24.4 Dimensions . 34.5 Shrinkage . 34.6 Basic properties . 44.7 Weathering behaviour 44.8 Other properties 45 Test methods . 45.1 General . 45.2 Colour 55.3 Dimensions . 55.4 Mechanical properties 55.5 Thermal properties . 65.6 Optic

17、al properties . 65.7 Weathering behaviour 66 Reaction to fire . 77 Use in contact with food 78 Retest and rejection 7Annex A (normative) Determination of change in dimensions at elevated temperature (shrinkage) . 8BS EN ISO 11963:2012ISO 11963:2012(E)ForewordISO (the International Organization for S

18、tandardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the ri

19、ght to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International

20、 Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an

21、 International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 119

22、63 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.This second edition cancels and replaces the first edition (ISO 11963:1995), which has been technically revised.iv ISO 2012 All rights reservedBS EN ISO 11963:2012INTERNATIONAL STANDARD ISO 11963:2012(E)Plastics

23、 Polycarbonate sheets Types, dimensions and characteristics1 ScopeThis International Standard specifies the requirements for solid, flat extruded sheets of polycarbonate (PC) for general applications. It applies specifically to sheets made of poly(p,p-isopropylidene-diphenyl carbonate). The sheets m

24、ay be coloured or colourless, and they may be transparent, translucent or opaque. The sheets may also have a special weather-protective layer on one or both surfaces.This International Standard applies only to thicknesses equal to or greater than 1,5 mm.2 Normative referencesThe following documents,

25、 in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 62:2008, Plastics Determinat

26、ion of water absorptionISO 75-1, Plastics Determination of temperature of deflection under load Part 1: General test methodISO 75-2:2004, Plastics Determination of temperature of deflection under load Part 2: Plastics and eboniteISO 179-1:2010, Plastics Determination of Charpy impact properties Part

27、 1: Non-instrumented impact testISO 291, Plastics Standard atmospheres for conditioning and testingISO 306:2004, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST)ISO 489:1999, Plastics Determination of refractive indexISO 527-1, Plastics Determination of tensile pro

28、perties Part 1: General principlesISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plasticsISO 877-1, Plastics Methods of exposure to solar radiation Part 1: General guidanceISO 877-2, Plastics Methods of exposure to solar radiation Part 2: D

29、irect weathering and exposure behind window glassISO 877-3, Plastics Methods of exposure to solar radiation Part 3: Intensified weathering using concentrated solar radiationISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer m

30、ethod and titration methodISO 2818, Plastics Preparation of test specimens by machiningISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspectionISO 2859-10, Sampling procedures for inspection by attribute

31、s Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributesISO 4892-1, Plastics Methods of exposure to laboratory light sources Part 1: General guidance ISO 2012 All rights reserved 1BS EN ISO 11963:2012ISO 11963:2012(E)ISO 4892-2, Plastics Methods of exposu

32、re to laboratory light sources Part 2: Xenon-arc lampsISO 7391-1, Plastics Polycarbonate (PC) moulding and extrusion materials Part 1: Designation system and basis for specificationsISO 8256:2004, Plastics Determination of tensile-impact strengthISO 11359-2, Plastics Thermomechanical analysis (TMA)

33、Part 2: Determination of coefficient of linear thermal expansion and glass transition temperatureISO 13468-1, Plastics Determination of the total luminous transmittance of transparent materials Part 1: Single-beam instrumentISO 14782, Plastics Determination of haze for transparent materialsIEC 60093

34、, Methods of test for volume resistivity and surface resistivity of solid electrical insulating materialsCIE 15, ColorimetryCIE 85, Solar spectral irradiance3 Composition3.1 The following type of PC is preferred for PC sheet extrusion:Thermoplastics ISO 7391-PC,E,61-09(see ISO 7391-1 for explanation

35、 of designation system for PC)3.2 The sheet may contain colorants, additives, processing aids and stabilizers (e.g. UV-absorbers) up to a total mass content of 5 %.3.3 Sheets of the type specified in Clause 4 may have a protective layer (on one or both surfaces) with a UV-absorber content higher tha

36、n that of the substrate. The composition of the protective layer (e.g. polycarbonate and UV-absorber, or PMMA and UV-absorber, or other materials) and the application techniques (e.g. co-extrusion, coating, lamination, flow-coating, dipping) are not specified by this International Standard.4 Require

37、ments4.1 MaskingThe surface of the sheet as delivered shall be protected by plastic film or paper or a combination of both.4.2 AppearanceRequirements concerning defects and optical quality shall be agreed upon between the interested parties.4.3 ColourThe colorant(s) shall be homogeneously and unifor

38、mly distributed throughout the material, unless otherwise specified. For critical requirements, the degree of homogeneity shall be specified by the interested parties.2 ISO 2012 All rights reservedBS EN ISO 11963:2012ISO 11963:2012(E)4.4 Dimensions4.4.1 Conditions of measurementMeasurements should p

39、referably be made under the standard conditions 23 C 2 C and (50 10) % relative humidity. For measurements made under ambient conditions, allowance shall be made for dimensional changes due to the differences in temperature and relative humidity at the place of measurement from the preferred tempera

40、ture and relative humidity.4.4.2 Length and widthThe length and width of the sheets shall be agreed upon between the interested parties. The tolerances on length and width shall be as specified in Table 1.Table 1 Tolerances on length and widthLength or width mmToleranceUp to 1 00003+mmFrom 1 001 to

41、2 00006+mmFrom 2 001 to 3 00009+mm3 001 and over003+ ,%4.4.3 Deviation of shape from rectangularThe difference l between the lengths of the two diagonals of the rectangular sheet shall be less than 3,5 103 b (where b is the width, in millimetres, of the sheet, measured perpendicular to the direction

42、 of extrusion), but need not be less than 2 mm.4.4.4 ThicknessThe tolerance on the thickness of the sheets shall be as specified in Table 2.Table 2 Tolerances on thicknessThickness, d mmTolerance %1,5 d 5 5 d10 54.5 ShrinkageThe maximum shrinkage (see 5.5.3) shall be as specified in Table 3.Table 3

43、Maximum shrinkageThickness, d mmMaximum shrinkage %1,5 d 5 5 d10 5 ISO 2012 All rights reserved 3BS EN ISO 11963:2012ISO 11963:2012(E)4.6 Basic propertiesThe basic mechanical, thermal and optical properties of transparent, colourless sheets shall be as specified in Table 5. For other grades, the req

44、uired properties shall be agreed upon between the interested parties.4.7 Weathering behaviourAny requirements on natural- or artificial-weathering behaviour shall be agreed upon between the interested parties, as required.4.8 Other propertiesOther properties of transparent, colourless sheets, needed

45、 for specific applications, shall be agreed upon between the interested parties. Examples of, and test methods for, such properties are presented in Table 4.Table 4 Typical values of other properties of transparent, colourless sheetsUnit Test method Typical valueDensity g/cm3ISO 1183-1 1,2Coefficien

46、t of linear thermal expansion K1ISO 11359-2 65 106Refractive index, n20DISO 489:1999, method A1,59Haze (3 mm) % ISO 14782 1Surface resistivity IEC 60093 1015Water absorption (pre-conditioning: 50 C/24 h; immersion time in water: 24 h)mgISO 62:2008, method 116For other grades, the required properties

47、 shall be agreed upon between the interested parties.5 Test methods5.1 General5.1.1 SamplingThe sampling procedure shall be agreed upon between the interested parties. The procedures described in ISO 2859-1 and ISO 2859-10 are widely accepted and frequently used. Hence these are recommended for samp

48、ling.5.1.2 Conditioning and testing of specimensConditioning (48 h) and testing of specimens shall be carried out at 23 C 2 C and (50 10) % relative humidity, in accordance with ISO 291, except for the Vicat softening temperature and the temperature of deflection under load (see 5.5.1 and 5.5.2).5.1

49、.3 Preparation of specimensSpecimens shall be prepared, wherever applicable, in accordance with the procedures described in ISO 2818. When it is necessary to machine the sheet to reduce its thickness to the dimension required for a particular test method, one original surface shall be left intact.4 ISO 2012 All rights reservedBS EN ISO 11963:2012ISO 11963:2012(E)With PC sheets coated on one side, the coated side shall remain unmachined