EN ISO 11372-2011 en Gas cylinders - Acetylene cylinders - Filling conditions and filling inspection《气瓶 乙炔气瓶 充装条件和充装检查》.pdf

《EN ISO 11372-2011 en Gas cylinders - Acetylene cylinders - Filling conditions and filling inspection《气瓶 乙炔气瓶 充装条件和充装检查》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 11372-2011 en Gas cylinders - Acetylene cylinders - Filling conditions and filling inspection《气瓶 乙炔气瓶 充装条件和充装检查》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11372:2011Gas cylinders Acetylenecylinders Filling conditionsand filling inspection (ISO11372:2011)BS EN ISO 11372:2011 BRITISH STANDARDNational forewordThis British St

2、andard is the UK implementation of EN ISO11372:2011. It supersedes BS EN 12754:2002 and BS EN 1801:1999which are withdrawnThe UK participation in its preparation was entrusted to TechnicalCommittee PVE/3/7, Gas containers - Gas cylinder (receptacle)operations.A list of organizations represented on t

3、his committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012ISBN 978 0 580 67806 6ICS 23.020.30Compliance with a British Standa

4、rd cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2012.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11372 December 2011 I

5、CS 23.020.30 Supersedes EN 12754:2001, EN 1801:1998English Version Gas cylinders - Acetylene cylinders - Filling conditions and filling inspection (ISO 11372:2011) Bouteilles gaz - Bouteilles dactylne - Conditions de remplissage et de contrle au remplissage (ISO 11372:2011) Gasflaschen - Acetylenfla

6、schen - Fllbedingungen und Inspektion beim Fllen (ISO 11372:2011) This European Standard was approved by CEN on 15 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar

7、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

8、other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republ

9、ic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE N

10、ORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11372:2011: EBS EN ISO 11372:2011EN ISO 11372:2011 (E) 3 Foreword This docume

11、nt (EN ISO 11372:2011) has been prepared by Technical Committee ISO/TC 58 “Gas cylinders“ in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publ

12、ication of an identical text or by endorsement, at the latest by June 2012, and conflicting national standards shall be withdrawn at the latest by June 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall

13、 not be held responsible for identifying any or all such patent rights. This document supersedes EN 1801:1998, EN 12754:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Bel

14、gium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsem

15、ent notice The text of ISO 11372:2011 has been approved by CEN as a EN ISO 11372:2011 without any modification. BS EN ISO 11372:2011ISO 11372:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduction . v 1 Scope 1 2 Terms and definitions . 1 3 Filling inspection . 3 3.1 General

16、. 3 3.2 Pre-fill inspection 3 3.3 Solvent content 4 3.4 Inspection during filling 5 3.5 Post-fill inspection 6 4 Specific filling inspection of solvent-free acetylene cylinders . 6 4.1 Pre-fill inspection 6 4.2 Post-fill inspection 7 Annex A (informative) Safe operating diagram 8 Annex B (normative)

17、 Determination of the solvent content in acetylene cylinders 11 Bibliography 13 BS EN ISO 11372:2011ISO 11372:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

18、of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-government

19、al, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The mai

20、n task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Att

21、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11372 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 4, Operational r

22、equirements for gas cylinders. This third edition cancels and replaces the second edition (ISO 11372:2005), with the following main technical revisions: a) ISO 11372:2005 was revised taking into account EN 12754 and EN 1801. b) The clauses concerning filling inspection were restructured in order to

23、better reflect the actual proceeding of the filling inspection. c) A new subclause 3.3 with requirements and information regarding the solvent content was added. d) A new Clause 4 concerning the specific filling inspection of solvent-free acetylene cylinders was added. e) A new informative Annex A i

24、ntroducing the Safe operating diagram was added in order to improve the understanding of the importance of correct filling conditions for acetylene cylinders. f) A new normative Annex B outlining the calculations necessary for determination of the solvent content was added. BS EN ISO 11372:2011ISO 1

25、1372:2011(E) ISO 2011 All rights reserved vIntroduction This International Standard aims at the harmonization of the different operating and filling conditions of individual acetylene cylinders and covers requirements that reflect current practice and experience regarding the inspection at the time

26、of filling. ISO 11372 is intended to be used under a variety of national regulatory regimes but has been written so that it is suitable for the application of the UN Model Regulations1. Where there is any conflict between this International Standard and any applicable regulation, the regulation alwa

27、ys takes precedence. In International Standards, weight is equivalent to a force, expressed in newtons. However, in common parlance (as used in terms defined in this International Standard), the word “weight” continues to be used to mean “mass”, but this practice is deprecated (see ISO 80000-4). In

28、this International Standard the unit bar is used, due to its universal use in the field of technical gases. It should, however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is pascals (Pa). Pressure values given in this International Standard are given as gaug

29、e pressure (pressure exceeding atmospheric pressure) unless noted otherwise. BS EN ISO 11372:2011BS EN ISO 11372:2011INTERNATIONAL STANDARD ISO 11372:2011(E) ISO 2011 All rights reserved 1Gas cylinders Acetylene cylinders Filling conditions and filling inspection 1 Scope This International Standard

30、specifies minimum requirements for the filling conditions and filling inspection of acetylene cylinders. This International Standard is not applicable to an assembly of cylinders connected by a manifold, e.g. bundles (see ISO 13088). 2 Terms and definitions For the purposes of this document, the fol

31、lowing terms and definitions apply. 2.1 acetylene cylinder cylinder manufactured and suitable for the transport of acetylene, containing a porous material and solvent (where applicable) for acetylene, with a valve and other accessories affixed to the cylinder NOTE 1 For solvent-free acetylene cylind

32、ers, see Clause 4. NOTE 2 When there is no risk of ambiguity, the word “cylinder” is used. 2.2 cylinder shell acetylene cylinders empty cylinder manufactured and suitable for receiving and containing a porous material for use as part of an acetylene cylinder 2.3 filler gas cylinders trained person r

33、esponsible for inspection prior to, during and immediately after filling 2.4 maximum acetylene content acetylene cylinders specified maximum weight of acetylene including saturation acetylene in the cylinder 2.5 maximum acetylene charge acetylene cylinders maximum acetylene content minus the saturat

34、ion gas 2.6 porous material acetylene cylinders single- or multiple-component material introduced to or formed in the cylinder shell that, due to its porosity, allows the absorption of a solvent/acetylene solution NOTE The porous material may be either: monolithic, consisting of a solid product obta

35、ined by reacting materials or by materials connected together with a binder, or non-monolithic, consisting of granular, fibrous or similar materials without the addition of a binder. BS EN ISO 11372:2011ISO 11372:2011(E) 2 ISO 2011 All rights reserved2.7 residual gas acetylene cylinders weight of ac

36、etylene including the saturation acetylene, contained in a cylinder returned for filling 2.8 saturation gas acetylene cylinders acetylene that remains dissolved in the solvent in the cylinder at atmospheric pressure (1,013 bar) and at a temperature of 15 C 2.9 solvent acetylene cylinders liquid that

37、 is absorbed by the porous material and is capable of dissolving and releasing acetylene NOTE The following abbreviations are used: “A” for acetone; “DMF” for dimethylformamide. 2.10 specified solvent content acetylene cylinders weight of solvent that the acetylene cylinder shall contain in accordan

38、ce with the type approval 2.11 tare acetylene cylinders reference weight of the acetylene cylinder including the specified solvent content NOTE 1 The tare is further specified in accordance with definitions 2.11.1 to 2.11.3. NOTE 2 For cylinders with solvent, the tare is expressed by indicating eith

39、er tare S or both, tare A and tare S. For solvent-free acetylene cylinders, the tare is expressed by indicating tare F. For the tare used for cylinders in bundles, see ISO 13088. 2.11.1 tare A acetylene cylinders sum of the weights of the empty cylinder shell, the porous material, the specified solv

40、ent content, the valve, the coating, where applicable, and all other parts which are permanently attached (e.g. by clamping or bolting) to the cylinder when it is presented to be filled 2.11.2 tare S acetylene cylinders tare A plus the weight of the saturation gas 2.11.3 tare F acetylene cylinders t

41、are A minus the specified solvent content 2.12 total weight acetylene cylinders tare A plus the maximum acetylene content or tare S plus the maximum acetylene charge, respectively NOTE 1 For solvent-free cylinders, the total weight is tare F plus the maximum acetylene content. NOTE 2 The stamped val

42、ue can be less than the approved value. BS EN ISO 11372:2011ISO 11372:2011(E) ISO 2011 All rights reserved 32.13 working pressure acetylene cylinders settled pressure at a uniform reference temperature of 15 C in a cylinder containing the specified solvent content and the maximum acetylene content 3

43、 Filling inspection 3.1 General Each cylinder shall be submitted to an inspection prior to, during and immediately after filling. Filling of an acetylene cylinder includes determination of its solvent content and replenishment of its solvent, where applicable. The items described in 3.2 to 3.5 shall

44、 be covered by a filling inspection. Cylinders not fulfilling these requirements shall be clearly identified for further treatment according to the written procedures of the filling station. Cylinder owners may request that their authorization be obtained prior to their cylinders being filled. Such

45、ownership shall be established and this authorization obtained before filling the cylinders. The filling conditions of acetylene cylinders are established based on type testing according to ISO 3807 or other applicable regulations/standards. Filling conditions for acetylene cylinders are shown in th

46、e Safe operating diagram in Annex A, for information. 3.2 Pre-fill inspection 3.2.1 Verification of stamp-marking and necessary documentation The information required in the following lists shall be made available to the filler, for example, by providing him with appropriate documentation and by tra

47、ining. Before filling an acetylene cylinder, it shall be identified that: a) the cylinder is permitted for filling in the country of the filling station; b) the cylinder has not exceeded its due date for periodic inspection; c) the cylinder does not have a current history of problems; d) the stamp m

48、arking (in accordance with regional regulatory requirements and/or ISO 13769) and labelling (in accordance with regional regulatory requirements and/or ISO 7225) are appropriate to acetylene; NOTE For sovent-free acetylene cylinders, additional marking elements according to 4.1 need to be verified.

49、e) the colour coding (in accordance with regional regulatory requirements and/or regional industry practice), where applicable, is appropriate to acetylene. Before filling an acetylene cylinder, the following information shall be made available: 1) identification of the porous material; 2) type of solvent; 3) specified solvent content; 4) tare (with information whether tare A or tare S is used); 5) total weight and/or its maximum acetylene content (if tare A is used) or its maximum acetylene charge (if