EN ISO 11126-10-2004 en Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 10 Alman.pdf

《EN ISO 11126-10-2004 en Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 10 Alman.pdf》由会员分享，可在线阅读，更多相关《EN ISO 11126-10-2004 en Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 10 Alman.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 11126-10:2004 BS 7079-F10:2004 Incorporating Amendment No. 1 to BS 7079-F10:2000 (renumbers the BS as BS EN ISO 11126-10:2004) Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 10

2、: Almandite garnet The European Standard EN ISO 11126-10:2004 has the status of a British Standard ICS 25.220.10 BS EN ISO 11126-10:2004 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Stand

3、ards Committee and comes into effect on 15 November 2000 BSI 2 February 2005 ISBN 0 580 36665 0 National foreword This British Standard is the official English language version of EN ISO 11126-10:2004. It is identical with ISO 11126-10:2000. The UK participation in its preparation was entrusted to T

4、echnical Committee STI/21, Surface preparation of steel, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in th

5、is document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a co

6、ntract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals

7、 for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii

8、, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 15511 2 February 2005 Implementation of the European StandardEUROPEANSTANDA

9、RD NORMEEUROPENNE EUROPISCHENORM ENISO1112610 December2004 ICS25.220.10 Englishversion Preparationofsteelsubstratesbeforeapplicationofpaintsand relatedproductsSpecificationsfornonmetallicblastcleaning abrasivesPart10:Almanditegarnet(ISO1112610:2000) Prparationdessubjectilesdacieravantapplicationde p

10、einturesetdeproduitsassimilsSpcificationspour abrasifsnonmtalliquesdestinslaprparationpar projectionPartie10:Almandite(ISO1112610:2000) VorbereitungvonStahloberflchenvordemAuftragenvon BeschichtungsstoffenAnforderungenannichtmetallische StrahlmittelTeil10:Granat(Almandin)(ISO11126 10:2000) ThisEurop

11、eanStandardwasapprovedbyCENon21December2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtain

12、edonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions.

13、 CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMI

14、TTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO1112610:2004:EI NESO 11-62110:20( 40E) 2 Foreword The text of ISO 11

15、126-10:2000 has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 11126-10:2004 by Technical Committee CEN/TC 139 “Paints and varnishes“, the secretariat of which is held by DIN. This Eu

16、ropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/CENELEC Internal Regulations, the nationa

17、l standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

18、gal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 11126-10:2000 has been approved by CEN as EN ISO 11126-10:2004 without any modifications. ENISO1112610:2004INTERNATIONAL STANDARD ISO 11126-10 First edition 2000-08-01 Reference number ISO 1112

19、6-10:2000(E) OSI 2000 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 10: Almandite garnet Prparation des subjectiles dacier avant application de peintures et de produits assimils Spcifications pour abras

20、ifs non mtalliques destins la prparation par projection Partie 10: Almandite ENISO1112610:2004ii ENISO1112610:2004OSI 11-621100002:)E( ISO 0002 All rithgs rreseved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member

21、 bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental

22、 and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commis- sion (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Direct

23、ives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elem

24、ents of this part of ISO 11126 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 11126-10 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 12, Preparation of steel subst

25、rates before application of paints and related products. ISO 11126 consists of the following parts, under the general title Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives: Part 1: General introduction and cla

26、ssification Part 3: Copper refinery slag Part 4: Coal furnace slag Part 5: Nickel refinery slag Part 6: Iron furnace slag Part 7: Fused aluminium oxide Part 8: Olivine sand Part 9: Staurolite Part 10: Almandite garnet Part 2 has been deleted. ENISO1112610:2004blank ENISO1112610:2004ANRETNIITOLAN TSD

27、NADRA OSI 11-621100002:)E( ISO 0002 All rithgs rreseved 1 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 10: Almandite garnet WARNING Equipment, materials and abrasives used for surface preparation can b

28、e hazardous if used carelessly. Many national regulations exist for those materials and abrasives that are considered to be haz- ardous during or after use (waste management), such as free silica or carcinogenic or toxic substances. These regulations are therefore to be observed. It is important to

29、ensure that adequate instructions are given and that all required precautions are exercised. 1 Scope This part of ISO 11126 specifies requirements for almandite garnet abrasives, as supplied for blast-cleaning pro- cesses. It specifies ranges of particle sizes and values for apparent density, Mohs h

30、ardness, moisture content, con- ductivity of aqueous extract and water-soluble chlorides. The requirements specified in this part of ISO 11126 apply to abrasives supplied in the “new” condition only. They do not apply to abrasives either during or after use. Test methods for non-metallic blast-clean

31、ing abrasives are given in the various parts ISO 11127. NOTE 1 Information on commonly referenced national standards for non-metallic abrasives is given in the Bibliography. NOTE 2 Although this part of ISO 11126 has been developed specifically to meet requirements for preparation of steelwork, the

32、properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast- cleaning techniques. These techniques are described in ISO 8504-2:2000, Preparation of steel substrates before application of paints and related products Surface preparation

33、 methods Part 2: Abrasive blast-cleaning. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 11126. For dated references, subsequent amendments to, or revisions of, any of these publications do

34、not apply. However, parties to agreements based on this part of ISO 11126 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members o

35、f ISO and IEC maintain registers of currently valid International Standards. ISO 11127-1:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part 1: Sampling. ISO 11127-2:1993, Preparation of steel substrates

36、before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part 2: Determination of particle size distribution. ISO 11127-3:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleani

37、ng abrasives Part 3: Determination of apparent density. ENISO1112610:2004ISO -62111:01(0002E) 2 ISO 0002 All rithgs rreseved ISO 11127-4:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part 4: Assessment o

38、f hardness by a glass slide test. ISO 11127-5:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-cleaning abrasives Part 5: Determination of moisture. ISO 11127-6:1993, Preparation of steel substrates before application of pain

39、ts and related products Test methods for non-metallic blast-cleaning abrasives Part 6: Determination of water-soluble contaminants by conductivity measurement. ISO 11127-7:1993, Preparation of steel substrates before application of paints and related products Test methods for non-metallic blast-clea

40、ning abrasives Part 7: Determination of water-soluble chlorides. 3 Term and definition For the purposes of this part of ISO 11126, the following term and definition apply. 3.1 almandite garnet material manufactured from the naturally occurring mineral garnet which is dried and sieved, with or withou

41、t mechanical crushing, and prepared for use as a blast-cleaning abrasive NOTE 1 Almandite garnet is an iron aluminium silicate with the chemical formula Fe 3 Al 2 (SiO 4 ) 3 . NOTE 2 Other forms of garnet, such as andradite garnet which is a calcium iron silicate with the chemical formula Ca 3 Fe 2

42、(SiO 4 ) 3 , exist, but these garnet abrasives are not covered by this part of ISO 11126. 4 Designation of abrasives Almandite garnet abrasives shall be identified by “Abrasive ISO 11126” and the abbreviation N/GA indicating non- metallic, almandite garnet abrasive. This shall be followed, without s

43、paces, by an oblique stroke and then by the sym- bol G to indicate the required particle shape of the abrasive, when purchased, as grit. The designation shall be com- pleted by values denoting the particle size range, in millimetres, required (see Table 1). EXAMPLE Abrasive ISO 11126 N/GA/G 0,2-1 de

44、notes an abrasive of the non-metallic almandite garnet type, complying with the requirements of this part of ISO 11126, of initial particle shape grit and particle size range to . It is essential that this full product designation is quoted on all orders. Table 1 Particle size distribution Particle

45、size range a mm 0,2 to 0,5 0,2 to 1 0,2 to 1,4 0,2 to 2 0,2 to 2,8 0,5 to 1 0,5 to 1,4 1,0 to 2 1,4 to 2,8 Oversize Sieve size mm 0,5 1 1,4 2 2,8 1 1,4 2 2,8 R e s i d u e m a x .1 01 01 01 01 01 01 01 01 0 Nominal size Sieve size mm 0,2 0,2 0,2 0,2 0,2 0,5 0,5 1 1,4 R e s i d u e m i n .8 58 58 58

46、58 58 08 08 08 0 Undersize Sieve size mm 0,2 0,2 0,2 0,2 0,2 0,5 0,5 1 1,4 Through-flow max. 5 5 5 5 5 10 10 10 10 a By agreement between the interested parties, abrasives of different particle size ranges may be mixed together. Details of pro- portions of nominal size, oversize and undersize shall

47、be specified. The maximum particle size shall not exceed and the proportion of particles less than shall not exceed . 0,2 mm 1 mm % (m=m) % (m=m) % (m=m) 3,15 mm 0,2 mm 5 % (m=m) ENISO1112610:2004OSI 11-621100002:)E( ISO 0002 All rithgs rreseved 3 5 Sampling Sampling procedures shall be as specified

48、 in ISO 11127-1. 6 Requirements 6.1 General requirements Almandite garnet abrasives are natural mineral grains that absorb no water but may be wetted on the surface only. Silica in almandite garnet abrasives shall be present as bound silicate. The content of free crystalline silica (such as quartz, tridimite or crystobalite) shall not exceed , as determined by X-ray diffraction. The material shall be free f