EN ISO 10077-2-2017 en Thermal performance of windows doors and shutters - Calculation of thermal transmittance - Part 2 Numerical method for frames.pdf

《EN ISO 10077-2-2017 en Thermal performance of windows doors and shutters - Calculation of thermal transmittance - Part 2 Numerical method for frames.pdf》由会员分享，可在线阅读，更多相关《EN ISO 10077-2-2017 en Thermal performance of windows doors and shutters - Calculation of thermal transmittance - Part 2 Numerical method for frames.pdf（86页珍藏版）》请在麦多课文档分享上搜索。

1、Thermal performance of windows, doors and shutters - Calculation of thermal transmittancePart 2: Numerical method for frames (ISO 10077-2:2017)BS EN ISO 10077-2:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN I

2、SO 10077-2 July 2017 ICS 91.060.50; 91.120.10 Supersedes EN ISO 10077-2:2012English Version Thermal performance of windows, doors and shutters - Calculation of thermal transmittance - Part 2: Numerical method for frames (ISO 10077-2:2017) Performance thermique des fentres, portes et fermetures - Cal

3、cul du coefficient de transmission thermique - Partie 2 : Mthode numrique pour les encadrementes (ISO 10077-2:2017) Wrmetechnisches Verhalten von Fenstern, Tren und Abschlssen - Berechnung des Wrmedurchgangskoeffizienten - Teil 2: Numerisches Verfahren fr Rahmen (ISO 10077-2:2017) This European Stan

4、dard was approved by CEN on 27 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin

5、g such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into it

6、s own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germa

7、ny, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOM

8、ITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10077-2:2017 ENational forewordThis British Standard is the UK implementation of EN ISO 10077

9、-2:2017. It is identical to ISO 10077-2:2017. It supersedes BS EN ISO 10077-2:2012, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee IST/15, Software and systems engineering.A list of organizations represented on this committee can be obtained on reques

10、t to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 90108 9ICS 91.060.50; 91.120.10Compliance with a

11、 British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN ISO 10077-2:2017EUROPEAN ST

12、ANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10077-2 July 2017 ICS 91.060.50; 91.120.10 Supersedes EN ISO 10077-2:2012English Version Thermal performance of windows, doors and shutters - Calculation of thermal transmittance - Part 2: Numerical method for frames (ISO 10077-2:2017) Performance thermi

13、que des fentres, portes et fermetures - Calcul du coefficient de transmission thermique - Partie 2 : Mthode numrique pour les encadrementes (ISO 10077-2:2017) Wrmetechnisches Verhalten von Fenstern, Tren und Abschlssen - Berechnung des Wrmedurchgangskoeffizienten - Teil 2: Numerisches Verfahren fr R

14、ahmen (ISO 10077-2:2017) This European Standard was approved by CEN on 27 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lis

15、ts and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

16、 the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yu

17、goslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COM

18、IT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10077-2:2017 EBS EN ISO 10077-2:2017EN ISO 10777-2

19、:2017 (E) 3 European foreword This document (EN ISO 10777-2:2017) has been prepared by Technical Committee CEN/TC 89 “Thermal performance of buildings and building components”, the secretariat of which is held by SIS, in collaboration with Technical Committee ISO/TC 163 “Thermal performance and ener

20、gy use in the built environment“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2018 and conflicting national standards shall be withdrawn at the latest by January 2018. Attention is dra

21、wn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade A

22、ssociation. This document is part of the set of standards on the energy performance of buildings (the set of EPB standards) and has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association (Mandate M/480, see reference EF1 below), and supports ess

23、ential requirements of EU Directive 2010/31/EC on the energy performance of buildings (EPBD, EF2). In case this standard is used in the context of national or regional legal requirements, mandatory choices may be given at national or regional level for such specific applications, in particular for t

24、he application within the context of EU Directives transposed into national legal requirements. Further target groups are users of the voluntary common European Union certification scheme for the energy performance of non-residential buildings (EPBD art.11.9) and any other regional (e.g. Pan Europea

25、n) parties wanting to motivate their assumptions by classifying the building energy performance for a dedicated building stock. This document supersedes EN ISO 10077-2:2012. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Associatio

26、n. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

27、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. References: EF1 Mandate M480, Mandate to CEN, CENELEC and ETSI for the elabo

28、ration and adoption of standards for a methodology calculating the integrated energy performance of buildings and promoting the energy efficiency of buildings, in accordance with the terms set in the recast of the Directive on the energy performance of buildings (2010/31/EU) of 14th December 2010 BS

29、 EN ISO 10077-2:2017EN ISO 10777-2:2017 (E) 4 EF2 EPBD, Recast of the Directive on the energy performance of buildings (2010/31/EU) of 14thDecember 2010 Endorsement notice The text of ISO 10777-2:2017 has been approved by CEN as EN ISO 10777-2:2017 without any modification. BS EN ISO 10077-2:2017Thi

30、s page deliberately left blank ISO 10077-2:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 24 Symbols and subscripts . 24.1 Symbols . 24.2 Subscripts 35 Calculation method 35.1 Output of the method 35.2 General principle . 35.3 Validation of the calculati

31、on programs 46 Calculation of thermal transmittance 46.1 Output data 46.2 Calculation time intervals 46.3 Input data 46.3.1 Geometrical characteristics 46.3.2 Thermal conductivity values . 56.3.3 Emissivity of surfaces 66.3.4 General boundaries . 66.3.5 Boundaries for roller shutter boxes 66.4 Calcu

32、lation procedures 76.4.1 Determination of thermal transmittance . 76.4.2 Treatment of cavities using the radiosity method 86.4.3 Treatment of cavities using the single equivalent thermal conductivity method 187 Report .247.1 Contents of report . 247.2 Geometrical data 247.3 Thermal data 257.3.1 Ther

33、mal conductivity 257.3.2 Emissivity 257.3.3 Boundary conditions .257.4 Presentation of results 25Annex A (normative) Input and method selection data sheet Template 26Annex B (informative) Input and method selection data sheet Default choices 28Annex C (normative) Regional references in line with ISO

34、 Global Relevance Policy 30Annex D (normative) Thermal conductivity and other characteristics of selected materials 31Annex E (normative) Surface resistances .34Annex F (normative) Determination of the thermal transmittance .36Annex G (normative) General examples for the validation of calculation pr

35、ograms using the radiosity method for the treatment of cavities 40Annex H (normative) Examples of window frames for the validation of calculation programs using the radiosity method for the treatment of cavities .45Annex I (normative) Examples of window frames for the validation of calculation progr

36、ams using the single equivalent thermal conductivity method for the treatment of cavities .57Annex J (normative) Wood species listed in Annex D 68 ISO 2017 All rights reserved iiiContents PageISO 10077-2:2017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 24

37、Symbols and subscripts . 24.1 Symbols . 24.2 Subscripts 35 Calculation method 35.1 Output of the method 35.2 General principle . 35.3 Validation of the calculation programs 46 Calculation of thermal transmittance 46.1 Output data 46.2 Calculation time intervals 46.3 Input data 46.3.1 Geometrical cha

38、racteristics 46.3.2 Thermal conductivity values . 56.3.3 Emissivity of surfaces 66.3.4 General boundaries . 66.3.5 Boundaries for roller shutter boxes 66.4 Calculation procedures 76.4.1 Determination of thermal transmittance . 76.4.2 Treatment of cavities using the radiosity method 86.4.3 Treatment

39、of cavities using the single equivalent thermal conductivity method 187 Report .247.1 Contents of report . 247.2 Geometrical data 247.3 Thermal data 257.3.1 Thermal conductivity 257.3.2 Emissivity 257.3.3 Boundary conditions .257.4 Presentation of results 25Annex A (normative) Input and method selec

40、tion data sheet Template 26Annex B (informative) Input and method selection data sheet Default choices 28Annex C (normative) Regional references in line with ISO Global Relevance Policy 30Annex D (normative) Thermal conductivity and other characteristics of selected materials 31Annex E (normative) S

41、urface resistances .34Annex F (normative) Determination of the thermal transmittance .36Annex G (normative) General examples for the validation of calculation programs using the radiosity method for the treatment of cavities 40Annex H (normative) Examples of window frames for the validation of calcu

42、lation programs using the radiosity method for the treatment of cavities .45Annex I (normative) Examples of window frames for the validation of calculation programs using the single equivalent thermal conductivity method for the treatment of cavities .57Annex J (normative) Wood species listed in Ann

43、ex D 68 ISO 2017 All rights reserved iiiContents PageBS EN ISO 10077-2:2017ISO 10077-2:2017(E)Bibliography .70iv ISO 2017 All rights reservedBS EN ISO 10077-2:2017ISO 10077-2:2017(E)Bibliography .70iv ISO 2017 All rights reserved ISO 10077-2:2017(E)ForewordISO (the International Organization for Sta

44、ndardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the righ

45、t to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures

46、used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rul

47、es of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights ide

48、ntified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanat

49、ion on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.ISO 10077-2 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 89, Thermal performance of buildings and building components, in collaboration with ISO Technical Committee ISO/