EN ISO 9097-1994 en Small Craft - Electric Fans (Incorporates Amendment A1 2000)《小艇 电扇 包含修改件A1-2000 ISO 9097-1991》.pdf

《EN ISO 9097-1994 en Small Craft - Electric Fans (Incorporates Amendment A1 2000)《小艇 电扇 包含修改件A1-2000 ISO 9097-1991》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 9097-1994 en Small Craft - Electric Fans (Incorporates Amendment A1 2000)《小艇 电扇 包含修改件A1-2000 ISO 9097-1991》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、STDmESI BS EN IS0 9097-ENGL 1995 II Lb24bb9 0905b45 392 11 BRITISH STANDARD Small craft - Electric fans The European Standard EN IS0 9097:1994, with the incorporation of amendment A1:2000, has the status of a British Standard ICs 47.080 BS EN IS0 9097:1995 Incorporating Amendment No. 1 NO COPYING WI

2、THOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTDmBSI BS EN IS0 9097-ENGL 1995 m 1624bb9 090564b 227 BS EN IS0 9097:1995 12071 The following BSI references Committees responsible for this British Sta

3、ndard May 2001 Addition of Annex ZB The preparation of this British Standard was entrusted to Technical Committee GME/33, Small craft, upon which the following bodies were represented: British Canoe Manufacturers Association British Marine Industries Federation British Nautical Instrument Trade Asso

4、ciation British Waterways Board Consumer Policy Committee of BSI Department of Trade and Industry Department of Trade and Industry (Standards Policy Unit) Federation of Wire Rope Manufacturers of Great Britain Fire Extinguishing Trades Association Home Office Lloyds Register of Shipping Marine Safet

5、y Agency National Rivers Authority Personal Watercraft Association Royal Ocean Racing Club Royal Society for the Prevention of Accidents Royal Yachting Association Wolfson Institute Coopted members This British Standard, having been prepared under the direction of the Engineering Sector Committee, w

6、as published under the authority of the Standards Committee and comes into effect on 15 June 1995 O BSI 05-2001 Amendments issued since publication Amd.No. I Date I Comments standard Committee reference GME/33 Draft for comment 90/72268 DC ISBN O 580 24170 X COPYRIGHT European Committee for Standard

7、izationLicensed by Information Handling ServicesSTD-BSI BS EN IS0 9097-EMGL 2995 1621ihh9 0705b47 lb5 BS EN IS0 9097:1995 Contents Page Committees responsible Inside front cover ,. National foreword 11 Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 General requirements 3 5 Electrica

8、l requirements 4 6 Fanrating 4 7 Marking 5 Annex ZB (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives 6 O BSI 05-2001 i COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTDmBSI BS EN IS0 7097

9、-ENGL L995 D Lb24bb9 0905648 OTL II BS EN IS0 9097:1995 National foreword This British Standard has been prepared by Technical Committee GME133 and is the English language version of EN IS0 9097:1994 Small craft - Electric funs, including amendment A1:2000, published by the European Committee for St

10、andardization (CEN). It is identical with IS0 9097:1994 published by the International Organization for Standardization USO). EN IS0 9097 was produced as a result of international discussion in which the United Kingdom took an active part. Cross-references Attention is drawn to the fact that CEN and

11、 CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section

12、 entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Co

13、mpliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a hont cover, an inside hont cover, pages i and ii, the EN IS0 title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates

14、 when the document was last issued. 8 BSI 05-2001 11 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD-ES1 BS EN IS0 9097-ENGL 1995 D Lb24bb9 0905b49 T36 m EUROPEAN STANDARD EN IS0 9097 November 1994 NORME EUROPENNE EUROPISCHE NORM +Ai September 2000 ICs 2

15、3.120; 47.080 Descriptors: shipbuilding, small craft, ventilation, electricaly-operated devices, ventilators, specifications, tests, marking English version Small craft - Electric fans (includes amendment Al:2000) (IS0 9097:1991) Navires de plaisance - Ventilateurs lectriques Ventilatoren (inclu t l

16、amendement Al : 2000) (IS0 9097:1991) (IS0 9097:1991) Kleine Wasserfahrzeuge - Elektrische (enthlt nderung A1:2000) This European Standard was approved by CEN on 1994-11-10. Amendment A1:2000 was approved by CEN on 2000-09-01. CEN members are bound to comply with the CENKENELEC Internal Regulations

17、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European

18、Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national

19、standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Ko

20、mitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1994 Copyright reserved to CEN members _ Ref. No. EN IS0 9097:1994 +A1:2000 E COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesForeword This European Standard is the endorsement of IS0

21、 9097, Small craft, which was prepared by ISOPTC 188. This European Standard shall be given the status of a National Standard, either by publication of an identical text or by endorsement, at the latest by May 1995, and conflicting national standards shall be withdrawn at the latest by May 1995. Acc

22、ording to the CENICENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United K

23、ingdom. Foreword to amendment Al The text of this amendment EN IS0 9097:1994/A1:2000 to the EN IS0 9097:1994 from Technical Committee ISOPTC 188, Small craft, of the International Organization for Standardization (HO) has been taken over as an amendment to the European Standard by CENICMC. This amen

24、dment to the European Standard EN IS0 9097:1994 shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2001, and conflicting national standards shall be withdrawn at the latest by March 2001. This amendment to the Europe

25、an Standard EN IS0 9097:1994 has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this s

26、tandard. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, No

27、rway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 8 BSI 05-2001 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD.BSI BS EN IS0 9097-ENGL 1995 W 1bZlibb 0905b51 636 b EN IS0 9097:1994 1 Scope This International Standard specifies requirem

28、ents and describes test methods for measuring the airflow of fans intended for use in engine compartments, galley areas and other spaces on small craft in which mechanical ventilation is desirable. It applies to electrically operated fans rated for less than 50 volts direct current (d.c.). Fans may

29、be of the centrifugal or axial flow type. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revisio

30、n, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 8846:1990, Small craft - El

31、ectrical devices - Protection against ignition of surrounding flammable gases. AMCA Standard 210-85/ASHAE Standard 51:1985, Laboratory Methods of Testing Fans for, Rating.) BS 848-1:1980, Fans for general purposes - Part 1: Methods of testingperformance. DIN 24163-1:1985, Ventilatoren - Leistungsmes

32、sung - Normkennlinien. DIN 24163-2: 1985, Ventilatoren - Leistungsmessung - Normprufstnde. NF X 10-200: 1986, Rgles dessais arauliques en plateforme des ventilateurs enveloppe refoulants et aspirants-refoulants - Mthode du caisson rduit au refoulement. 3 Definitions For the purposes of this Internat

33、ional Standard, the following definitions apply. 3.1 ignition-protected device device that complies with the requirements of IS0 8846. (IS0 8846 describes appropriate test programmes) 3.2 nominal voltage commonly used direct current (d.c.) voltages on boats such as 6 V, 12 V, 24 V, 32 V 4 General re

34、quirements 4.1 Fans shall be designed to operate continuously at 120 % of nominal voltage. 4.2 Fans shall be ignition-protected in accordance with the requirements of IS0 8846. 4.3 Fans shall be rated for airflow. Fan airflow shall be measured in accordance with clause 6, and performance curves shal

35、l be available. 4.4 Materials used for fan blades or rotor and the housing shall be selected to prevent the creation of a spark should they contact each other. 4.5 Moving parts of fans shall, when necessary, be enclosed or fitted with guards for protection against injury. Enclosures shall be provide

36、d with drains to prevent the accumulation of water in all mounting positions. Enclosures and guards are not needed if contact with the fans moving parts is judged not to be harmful. 1) Published by Air Movement and Control Assoc., Inc. 30 West University Drive, Arlington Heights, IL 60004, USA. 8 BS

37、I 05-2001 3 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD*BSI BS EN IS0 9097-ENGL 1995 1624669 0905b52 522 H EN IS0 9097:1994 4.6 Fans shall be provided with a means for securely mounting them to the boat. 4.7 Components of fans shall be selected to be

38、galvanically compatible in the presence of sea-water. 4.8 Components of fans shall be selected or coated to be resistant to corrosion in the presence of sea-water. 4.9 Installation instructions including a fan performance curve shall be available for each fan (see 6.2). 5 Electrical requirements 5.1

39、 Fans shall be of the 2-wire type, with both the power and return lines insulated from the motor and fan housing. 5.2 Conductors used for connection to the power supply shall be stranded copper. NOTE 1 A future International Standard will specify requirements for extra-low-voltage electrical install

40、ations. 5.3 If external terminals are provided, they shall be designed or shielded to prevent short-circuiting that could result from accidental contact by a conductive object. 6.4 If external motor leads are provided with the fan, they shall be sized in accordance with the power requirement but not

41、 less than a nominal 1 mm2. Conductor insulation shall be rated to be used in damp places and be suitable for 60 “C ambient temperature at 120 % of nominal voltage. 5.5 A fan shall be protected against continuous locked rotor conditions by: - integral overcurrent protection; or, - overcurrent protec

42、tion in the circuit sized to protect the fan motor; or, - being capable of sustaining operation with a locked rotor for 7 h without generating surface temperatures in excess of 150 “C at an ambient temperature of 60 “C, and without evidence of charring, burning or melting. 6 Fan rating 6.1 Fans shal

43、l be rated electrically in volts and in amperes or watts. 6.2 Values for the fan rating, given in cubic metres per second, shall be plotted using the methods given in any of the relevant standards indicated. NOTE 2 References have been given to some national standards concerning tests for ratings, w

44、hich the future IS0 5801 will incorporate, replacing the national standards. 6.2.1 Fans with free inlet, ducted outlet (category B), see the following standards: - AMCA 210-85lASHRAE 51:1985, Figures 9 to 12; - BS 848-1, Figure 27a), Figure 27b), Figure 27c) and Figure 27d); - DIN 24163-1, Bild 1, P

45、riifstandsanordnung 2, Einbauart C; - NF X 10-200. 4 Q BSI 05-2001 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-QSI BS EN IS0 9097-ENGL I1995 E 3b24bb9 0905653 4b9 EN IS0 9097:1994 6.2.2 Fans with ducted inlet, free outlet (category C), see the followi

46、ng standards: - AMCA 210-851ASHRAE 51:1985, Figure 13, Figure 14 and Figure 15; - BS 848-1, Figure 28a), Figure 28b), Figure 2%) and Figure 28d); - DIN 24163-1, Bild A, Prfstandsanordnung 1, Einbauart B; - DIN 24163-2, Bild 4. 6.2.3 Fans with ducted inlet, ducted outlet (category D), see the followi

47、ng standards: - AMCA 210-85/ASHRAE 51:1985, Figure 9, Figure 10, Figure 11, Figure 12, Figure 13, Figure 14 and Figure 15; - BS 848-1, Figure 29a), Figure 29b), Figure 29c), Figure 29d) and Figure 29e); - DIN 24163-2, Bild 4. NOTE 3 Fans with free inlet and free outlet (category A) are not used in s

48、mall craft. 6.3 The procedure for rating a fan is as follows. Mount the fan to be tested making certain that all mating surfaces are sealed. Run the fan at 120 % of nominal voltage for a break-in period of 3 h prior to testing. Maintain the fan operating voltage at its nominal voltage throughout the

49、 test. Correct the airflow readings taken during the test to a standard density of 1,2 kglm3. Vary the total pressure in sufficient steps to develop a performance curve. 7 Marking 7.1 Fans shall be permanently and legibly marked with at least the following information: a) manufacturers or private labellers name or trademark b) model or type identification; c) year of manufacture (may be coded); d) electrical rating in volts and amperes or alternatively in volts and watts. 7.2 Evidence of compliance with this International Standard shall be indicated by