EN ISO 8986-1-2009 en Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1 Designation system and basis for specifications《塑料 聚丁烯-1(PB-1)模塑和挤塑材料 第1部分 命名体系和基本规范》.pdf

《EN ISO 8986-1-2009 en Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1 Designation system and basis for specifications《塑料 聚丁烯-1(PB-1)模塑和挤塑材料 第1部分 命名体系和基本规范》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 8986-1-2009 en Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 1 Designation system and basis for specifications《塑料 聚丁烯-1(PB-1)模塑和挤塑材料 第1部分 命名体系和基本规范》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO8986-1:2009ICS 83.080.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics Polybutene-1 (PB-1)moulding andextrusion materialsPart 1: Designation system and basisfor specifications (ISO 8986-1:2009)This British Standardwas published under theauthor

2、ity of the StandardsPolicy and StrategyCommittee on 31 December2009 BSI 2009ISBN 978 0 580 60083 8Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 8986-1:2009National forewordThis British Standard is the UK implementation of EN ISO 8986-1:2009.It supersedes BS EN ISO 8986-1:1999

3、which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof

4、a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8986-1 November 2009 ICS 83.080.20 Supersedes EN ISO 8986-1:1999English Version Plastics - Polybutene

5、-1 (PB-1) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 8986-1:2009) Plastiques - Matriaux base de polybutne-1 (PB-1) pour moulage et extrusion - Partie 1: Systme de dsignation et base de spcification (ISO 8986-1:2009) Kunststoffe - Polybuten-1 (PB-1

6、)-Formmassen - Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 8986-1:2009) This European Standard was approved by CEN on 21 October 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the statu

7、s of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A

8、version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic

9、, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NOR

10、MALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8986-1:2009: EBS EN ISO 8986-1:2009EN ISO 8986-1:2009 (E) 3 Foreword This docum

11、ent (EN ISO 8986-1:2009) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identic

12、al text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsibl

13、e for identifying any or all such patent rights. This document supersedes EN ISO 8986-1:1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Re

14、public, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8986-1:2009 ha

15、s been approved by CEN as a EN ISO 8986-1:2009 without any modification. BS EN ISO 8986-1:2009ISO 8986-1:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of p

16、reparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental,

17、in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main ta

18、sk of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attenti

19、on is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8986-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materia

20、ls. This second edition cancels and replaces the first edition (ISO 8986-1:1993), which has been technically revised. The main changes are as follows: it has been made clear that the standard concerns polybutene-1 as opposed to its isomer polyisobutene; density has been deleted as a designatory prop

21、erty; the only other designatory property, melt mass-flow rate (MFR), has been replaced by melt volume-flow rate (MVR); 190 C/5,0 kg has been added to the sets of conditions which can be used for the measurement of MVR. ISO 8986 consists of the following parts, under the general title Plastics Polyb

22、utene-1 (PB-1) moulding and extrusion materials: Part 1: Designation system and basis for specifications Part 2: Preparation of test specimens and determination of properties BS EN ISO 8986-1:2009BS EN ISO 8986-1:2009INTERNATIONAL STANDARD ISO 8986-1:2009(E) ISO 2009 All rights reserved 1Plastics Po

23、lybutene-1 (PB-1) moulding and extrusion materials Part 1: Designation system and basis for specifications 1 Scope 1.1 This part of ISO 8986 establishes a system of designation for polybutene-1 (PB-1) thermoplastic materials which may be used as the basis for specifications. For the sake of simplici

24、ty, the designation polybutene and the abbreviation PB are used in both parts of ISO 8986. 1.2 The types of polybutene plastics are differentiated from each other by a classification system based on appropriate levels of the designatory property melt volume-flow rate and on information about basic p

25、olymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of ISO 8986 is applicable to all butene homopolymers and to copolymers of butene with a maximum content of other 1-olefinic monomers of le

26、ss than 50 % by mass and with a content of non-olefinic monomers with functional groups up to a maximum of 1 % by mass. It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not

27、 intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 8986 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of pr

28、ocessing. 1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1). 2 Normative references The following referenced documents are indispensable for the application of this docume

29、nt. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics ISO 8986-2, Plastics Polybut

30、ene-1 (PB-1) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties BS EN ISO 8986-1:2009ISO 8986-1:2009(E) 2 ISO 2009 All rights reserved3 Designation and specification system 3.1 General The designation and specification system for thermoplastics is

31、based on the following standardized pattern: Designation Identity block Individual-item block Description block (optional) International Standard number block Data block1 Data block2 Data block3 Data block 4 Data block5 The designation consists of an optional description block, reading “Thermoplasti

32、cs”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Identification of the plastic by its symbol PB in accordance

33、 with ISO 1043-1 and information about the polymerization process or composition of the polymer (see 3.2). Data block 2: Position 1: Intended application or method of processing (see 3.3). Positions 2 to 8: Important properties, additives and supplementary information (see 3.3). Data block 3: Design

34、atory properties (see 3.4). Data block 4: Fillers or reinforcing materials and their nominal content (see 3.5). Data block 5: For the purpose of specifications, a fifth data block may be added containing additional information. The first character of the individual-item block shall be a hyphen. The

35、data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,). 3.2 Data block 1 In this data block, after the hyphen, polybutene plastics are identified by the symbol PB, in accordance with ISO 1

36、043-1, followed by a hyphen and a single code-letter giving additional information on the polymer as specified in Table 1. Table 1 Code-letters used for additional information in data block 1 Code-letter Definition H Butene homopolymer. B Thermoplastic butene “block” copolymer having not more than 5

37、0 % by mass of another olefinic monomer (or monomers) having no functional group other than the olefinic group, copolymerized with butene. R Thermoplastic butene random copolymer having not more than 50 % by mass of another olefinic monomer (or monomers) having no functional group other than the ole

38、finic group, copolymerized with butene. Q Blends of polymers with at least 50 % by mass of butene plastic H (homopolymer), B (“block” copolymer) and/or R (random copolymer). BS EN ISO 8986-1:2009ISO 8986-1:2009(E) ISO 2009 All rights reserved 33.3 Data block 2 In this data block, information about t

39、he intended application and/or method of processing is given in position 1 and information about important properties, additives and colour in positions 2 to 8. The code-letters used are specified in Table 2. If information is presented in positions 2 to 8 and no specific information is given in pos

40、ition 1, the letter X shall be inserted in position 1. Table 2 Code-letters used in data block 2 Code-letter Position 1 Code-letter Positions 2 to 8 A Processing stabilized B Blow moulding B Antiblocking C Calendering C Coloured D Powder E Extrusion E Expandable F Film extrusion F Special burning ch

41、aracteristics G General purpose G Granules H Coating H Heat ageing stabilized K Cable and wire coating K Metal deactivated L Monofilament extrusion L Light or weather stabilized M Moulding M Nucleated N Natural (no colour added) P Impact modified Q Compression moulding R Rotational moulding R Mould

42、release agent S Sintering S Lubricated T Tape manufacture T Transparent X No indication Y Increased electrical conductivity Z Antistatic 3.4 Data block 3 3.4.1 General In this data block, the range of the melt volume-flow rate (MVR) is represented by a three-figure code-number (see 3.4.2). NOTE 1 In

43、 this edition of ISO 8986-1, melt mass-flow rate (MFR) has been replaced by melt volume-flow rate (MVR). If the MVR value falls on or near a range limit, the manufacturer shall state which range will designate the material. If subsequent individual test values lie on, or on either side of, the limit

44、 because of manufacturing tolerances, the designation is not affected. NOTE 2 Not all values of MVR are necessarily provided by currently available polymers. BS EN ISO 8986-1:2009ISO 8986-1:2009(E) 4 ISO 2009 All rights reserved3.4.2 Melt volume-flow rate The melt volume-flow rate shall be determine

45、d as specified in ISO 8986-2 under the test conditions specified in Table 3. Table 3 Test conditions used for the determination of melt volume-flow rate Temperature Nominal load Code-letter C kg D 190 2,16 T 190 5,0 F 190 10,0 Set of conditions F shall be used only for materials having an MVR less t

46、han 0,1 cm3/10 min when tested under set of conditions D. The possible values of melt volume-flow rate are divided into 11 ranges, each represented by a three-figure code-number as specified in Table 4. The test conditions used shall be indicated by a single code-letter, selected from Table 3, immed

47、iately preceding the code-number. Table 4 Ranges of melt volume-flow rate in data block 3 Range of melt volume-flow rate Code-number cm3/10 min 000 u 0,10 001 0,10 but u 0,20 003 0,20 but u 0,40 006 0,40 but u 0,80 012 0,80 but u 1,5 022 1,5 but u 3,0 045 3,0 but u 6,0 090 6,0 but u 12,0 200 12,0 bu

48、t u 25,0 400 25,0 but u 50,0 700 50,0 3.5 Data block 4 In this data block, the type of filler and/or reinforcing material is represented by a single code-letter in position 1 and its physical form by a second code-letter in position 2, the code-letters being as specified in Table 5. Subsequently (wi

49、thout a space), the mass content may be given by a two-figure number in positions 3 and 4. BS EN ISO 8986-1:2009ISO 8986-1:2009(E) ISO 2009 All rights reserved 5Table 5 Code-letters for fillers and reinforcing materials in data block 4 Code-letter Material Code-letter Form B boron B beads, spheres, balls C carbonaD powder F fibre G glass G ground H whiskers I (inorganic) minerala,bK calcium carbonate L celluloseaM metalaS synthetic, organicaT talc X not specified X not specified Z othersaZ othersaa