EN ISO 7390-2003 en Building construction Jointing products Determination of resistance to flow of sealants《房屋建筑 焊接产品 密封剂流动性的测定 代替EN 27390-1990 ISO 7390-2003》.pdf

《EN ISO 7390-2003 en Building construction Jointing products Determination of resistance to flow of sealants《房屋建筑 焊接产品 密封剂流动性的测定 代替EN 27390-1990 ISO 7390-2003》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 7390-2003 en Building construction Jointing products Determination of resistance to flow of sealants《房屋建筑 焊接产品 密封剂流动性的测定 代替EN 27390-1990 ISO 7390-2003》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 7390:2003 Building construction Jointing products Determination of resistance to flow of sealants The European Standard EN ISO 7390:2003 has the status of a British Standard ICS 91.100.50 BS EN ISO 7390:2003 This British Standard was published under the authority of the St

2、andards Policy and Strategy Committee on 22 January 2004 BSI 22 January 2004 ISBN 0 580 43312 9 National foreword This British Standard is the official English language version of EN ISO 7390:2003. It is identical with ISO 7390:2002. It supersedes BS EN 27390:1991 (1998) which is withdrawn. The UK p

3、articipation in its preparation was entrusted to Technical Committee B/547, Sealants for building and construction, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which impleme

4、nt international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does

5、not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European

6、committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the

7、 EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, the Annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NOR

8、MEEUROPENNE EUROPISCHENORM ENISO7390 November2003 ICS91.100.50 SupersedesEN27390:1990 Englishversion BuildingconstructionJointingproductsDeterminationof resistancetoflowofsealants(ISO7390:2003) ConstructionimmobilireProduitspourjoints Dterminationdelarsistanceaucoulagedesmastics (ISO7390:2003) Hochb

9、auFugendichtstoffeBestimmungdes Standvermgens(ISO7390:2002) ThisEuropeanStandardwasapprovedbyCENon25September2003. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsan

10、dbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnot

11、ifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Hungary,Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,SwitzerlandandUn ited King

12、dom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2003CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO7390:2003EINESO37:0902(30E) 2 Foreword ThetextofIS

13、O7390:2002hasbeenpreparedbyTechnicalCommitteeISO/TC59“Building construction”oftheInternationalOrganizationforStandardization(ISO)andhasbeentaken overasENISO7390:2003byCMC. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyM

14、ay2004,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2004. ThisdocumentsupersedesEN27390:1990. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finlan

15、d,France,Germany,Greece,Hungary,Iceland,Ireland,Italy, Luxembourg,Malta,Netherlands,Norway,Portugal,Slovakia,Spain,Sweden,Switzerlandand theUnitedKingdom. Endorsementnotice ThetextofISO7390:2002hasbeenapprovedbyCENasENISO7390:2003withoutany modifications. NOTENormativereferencestoInternationalStanda

16、rdsarelistedinAnnexZA(normative). ENISO7390:2003INTERNATIONAL STANDARD ISO 7390 Third edition 2002-10-01 Reference number ISO 7390:2002(E) OSI 2002 Building construction Jointing products Determination of resistance to flow of sealants Construction immobilire Produits pour joints Dtermination de la

17、rsistance au coulage des masticsENISO7390:2003ISO :0937(2002)E ii ISO 2002 Ar llithgr seresvde FDP dicslaimre This FDP fam elitnoc yt deddebme niayfep.seca In roccatiw ecnadA hycilop gnisnecil sebod, thf sim eliarp eb ytnieiv ro dewb detu sllah ton eb tidesselnu de tt ehyfepseca hwich rae meil era d

18、eddebct desnetsni dna olat no delmoc ehtupre epfrromign tide ehti.gn In odaolnwt gnidihs file, rapticca setpe trehiet neh serilibisnopty fo ton fnirisebodA gnign ilop gnisnecilcy. TI ehSO tneCrceS larteraita catpecon s illibaity it nihs aera. ebodA si t armedarak fo dAS ebotsysme Inroctarop.de teDai

19、lfo s tfos ehtware prtcudos t desuo crtaet ehFDP si ff eb nac elit ni dnuoG ehlarene Info talerive to tf eh;eli teh PDF-rctaerap noimateers weer tpof dezimior rptnii.gn vErec yaeeb sah ert nakt neo rusnet etah tf ehi elis tiusbaf elob esu ry ISO merebm seidob. In the kilnuley evtne ttah a borpmel ta

20、lerign to ti f si,dnuo saelpfni erom teh tneCS larterceratai ta thserdda es igvne olebw. ISO 2002 Ar llieser sthgrvsselnU .de torehceps esiwfi,dei rap ont iht fos bupliactim noarper eb yro decudo tuzilina ni dey from b roy nasnaem y, tcelernahcem ro cinoicla, inclidung tohppocoying m dnaicrfomli, ti

21、wtuoh permini noiss wrtif gnirmo ietI rehSO ta tserdda eheb slow or SIsO memreb ydob in toc ehtnury fo tr ehtseuqeer. ISO copyrithg fofiec tsop esaCela 65 G 1121-HCeneva 02 T.le + 22 14 10 947 11 Fxa + 14 47 2290 9 74 E-liam cpoyrigthsio.ch Web wwwsi.oc.h ENISO7390:2003ISO 9372002:0)E( ISO 2002 r ll

22、Aithgs reservde iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a s

23、ubject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission

24、(IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inte

25、rnational Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent righ

26、ts. International Standard ISO7390 was prepared by Technical Committee ISO/TC59, Building construction, Subcommittee SC 8, Jointing products. This third edition cancels and replaces the second edition (ISO 7390:1987), which has been technically revised. ENISO7390:2003blank ENISO7390:2003ANRETNIITOTS

27、 LANDNADRA ISO 9372002:0)E( ISO 2002 r llAithgs reservde 1 Building construction Jointing products Determination of resistance to flow of sealants 1 Scope This International Standard specifies a method for the determination of the resistance to flow of sealants, by loss of cohesion under their own w

28、eight. These sealants are used in joints in vertical surfaces in building construction. 2 Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments

29、to, or revisions of, this publication do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the norma

30、tive document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 6927, Building construction Jointing products Sealants Vocabulary 3 Terms and definitions For the purposes of this International Standard, the terms and definitions for sealan

31、ts specified in ISO 6927 apply. 4 Principle The sealant, applied in a U-profile, is exposed for a defined time to various defined temperatures. The open surface of the sealant is in a vertical position during the test. The flow of the sealant out of the U-profile is measured at the end of the test p

32、eriod. 5A p p a r a t u s 5.1 Non-porous and smooth U-profiles, for example anodized or non-anodized aluminium, with a length of , with both ends open and optionally the back surface extended at one end (see Figures 1 and 2), having a cross section with the following internal dimensions: width: ; de

33、pth: . Other dimensions may be applied, for example width and depth . 5.2 Strips of polyethylene (PE) sheet, with the following dimensions: thickness ; width to cover the inner backside of the U-profile. Under test conditions, the length of the PE-strip shall not change by more than . 5.3 Ventilated

34、 convection-type oven, capable of operating at . (150 1,0) mm (20 0,2) mm (10 0,2) mm (10 0,2) mm (10 0,2) mm 0,5 mm 1mm (70 2) C ENISO7390:2003ISO :0937(2002)E 2 ISO 2002 Ar llithgr seresvde 5.4 Ventilated convection-type oven, capable of operating at . 5.5 Refrigerated container, capable of operat

35、ing at . 5.6 Measuring device, scaled in . 6 Test method 6.1 Preparation of test specimens The appropriate number of U-profiles used is determined according to 6.2. The U-profiles shall be first cleaned and dried. Place a strip of PE-sheet (5.2) along the backside base of each U-profile, overlapping

36、 at the top and fixed at the outer reverse side, for example with adhesive tape. The PE-strip shall exactly cover the inside base of the U-profile. NOTE If the PE-strip is too narrow, the sealant will adhere to the backside base of the U-profile. If the PE-strip is too wide, it will curl inwards dec

37、reasing the contact area between the sealant and the sides of the U-profile. Bring the U-profile and the sealant to . Fill the U-profile with sealant. The following precautions shall be taken: a) the formation of air bubbles shall be avoided; b) the sealant shall be pressed on the inner profile surf

38、aces; c) the sealant surface shall be trimmed so that it is flush with the face and ends of the U-profile; d) the polyethylene strip shall be loosened from the reverse side of the U-profile. 6.2 Procedures 6.2.1 General For each test temperature of and/or and/or , and for each procedure A and B, one

39、 test specimen shall be used. The test specimens shall be tested either according to procedure A (see 6.2.2) or procedure B (see 6.2.3), as agreed. In the case of the sealant sliding from the U-profile, the inner surface of the U-profile shall be treated in accordance with the sealant manufacturers

40、recommendations. The test shall be repeated. 6.2.2 Procedure A Immediately after the preparation (6.1), place the test specimen in the oven (5.3 or 5.4) or in the refrigerated container (5.5) in a vertical position with the possible extension of the U-profile at the bottom (see Figure 1). Submit eac

41、h test specimen to each defined test temperature for and then remove it from the oven or refrigerated container. Measure in a vertical direction, using the measuring device (5.6), the distance that the bottom edge of the sealant of each test specimen has moved downwards. (50 2) C (5 2) C 0,5 mm (23

42、2) C 70 C5 0 C5 C 24 h ENISO7390:2003ISO 9372002:0)E( ISO 2002 r llAithgs reservde 3 6.2.3 Procedure B Immediately after the preparation (6.1), place the test specimen in the oven (5.3 or 5.4) or in the refrigerated container (5.5), in a horizontal position with the open sealant surface in a vertica

43、l plane (see Figure 2). Submit each test specimen to each defined test temperature for and then remove it from the oven or refrigerated container. Measure in a horizontal direction, using the measuring device (5.6), the distance that the sealant has projected beyond the front of the U-profile of eac

44、h test specimen. Dimensions in millimetres a Optional Figure 1 Position of test specimen for procedure A Dimensions in millimetres a Optional Figure 2 Position of test specimen for procedure B 24 h ENISO7390:2003ISO :0937(2002)E 4 ISO 2002 Ar llithgr seresvde 7 Test report The test report shall cont

45、ain the following information: a) name of laboratory and date of test; b) a reference to this International Standard; c) name, type (chemical family) and colour of sealant; d) batch of sealant from which the test specimens were produced; e) type of profile used (anodized or non-anodized aluminium or

46、 other material); f) internal dimensions of U-profiles if different from those in 5.1; g) applied procedure according to 6.2; h) name and batch of the surface treatment, if any; i) flow of the sealant of each test specimen, in millimetres rounded to the nearest , stating the test temperature used; j

47、) any deviations from the method of this International Standard. 1mm ENISO7390:2003INESO37:0902(30E) 3 AnnexZA (normative) Normativereferencestointernationalpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundatedreference,provisionsfromother publications.Thesenormativereferencesarecitedattheappropriateplacesinthetextandthe publicationsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisionsof anyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.F