EN ISO 7048-2011 en Cross-recessed cheese head screws《带十字槽的圆头螺钉》.pdf

《EN ISO 7048-2011 en Cross-recessed cheese head screws《带十字槽的圆头螺钉》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 7048-2011 en Cross-recessed cheese head screws《带十字槽的圆头螺钉》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 7048:2011Cross-recessed cheese headscrewsBS EN ISO 7048:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 7048:2011. It sup

2、ersedes BS EN ISO 7048:1999, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e F M E / 9 / 3 , F a s t e n e r s - P r o d u c t S t a n d a r d s .A list of organizations represented on this committee can be obtained on request to its se

3、cretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 71154 1 ICS 21.060.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was

4、 published under the authority of the Standards Policy and Strategy Committee on 31 July 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 7048 April 2011 ICS 21.060.10 Supersedes EN ISO 7048:1998English Version Cross-recesse

5、d cheese head screws (ISO 7048:2011) Vis mtaux tte cylindrique empreinte cruciforme (ISO 7048:2011) Zylinderschrauben mit Kreuzschlitz (ISO 7048:2011) This European Standard was approved by CEN on 31 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipul

6、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European St

7、andard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the n

8、ational standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swit

9、zerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.

10、 EN ISO 7048:2011: EBS EN ISO 7048:2011 EN ISO 7048:2011 (E) 3 Foreword This document (EN ISO 7048:2011) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shal

11、l be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at the latest by October 2011. Attention is drawn to the possibility that some of the elements of this docu

12、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 7048:1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are

13、bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

14、n, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 7048:2011 has been approved by CEN as a EN ISO 7048:2011 without any modification. BS EN ISO 7048:2011ISO 7048:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) i

15、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe

16、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are d

17、rafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International

18、Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7048 was prepare

19、d by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 10, Product standards for fasteners. This second edition cancels and replaces the first edition (ISO 7048:1998), of which it constitutes a minor revision. BS EN ISO 7048:2011BS EN ISO 7048:2011INTERNATIONAL STANDARD ISO 7048:2011(E) ISO 2

20、011 All rights reserved 1Cross-recessed cheese head screws 1 Scope This International Standard specifies the characteristics of cross-recessed cheese head screws of product grade A, with threads from M2,5 to M8 inclusive, and with cross recesses of types H and Z. NOTE The head dimensions of these sc

21、rews are identical to those of the slotted cheese head screws in ISO 1207. If, in special cases, specifications others than those listed in this International Standard are required, they can be selected from existing International Standards, for example ISO 261, ISO 888, ISO 898-1, ISO 965-2, ISO 35

22、06-1 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2

23、25, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions ISO 261, ISO general purpose metric screw threads General plan ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse

24、thread and fine pitch thread ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality ISO 3269, Fasteners Acceptance inspection ISO 3506-1, Mechanical properties of corrosion-resistant stainless stee

25、l fasteners Part 1: Bolts, screws and studs ISO 4042, Fasteners Electroplated coatings ISO 4757, Cross recesses for screws ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C ISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and stud

26、s for general requirements ISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings BS EN ISO 7048:2011ISO 704

27、8:2011(E) 2 ISO 2011 All rights reserved3 Dimensions See Figure 1 and Table 1. The shank diameter is approximately equal to the pitch diameter or equal to the permissible major thread diameter. The symbols and descriptions of dimensions are specified in ISO 225. a) Type H b) Type Z a Edge may be rou

28、nded or flat. b As-rolled end. Figure 1 BS EN ISO 7048:2011ISO 7048:2011(E) ISO 2011 All rights reserved 3Table 1 Dimensions Dimensions in millimetres Thread, d M2,5 M3 (M3,5)aM4 M5 M6 M8 Pb0,45 0,5 0,6 0,7 0,8 1 1,25 a max. 0,9 1 1,2 1,4 1,6 2 2,5 b min. 25 25 38 38 38 38 38 max. 4,50 5,50 6,00 7,0

29、0 8,50 10,00 13,00 dkmin. 4,32 5,32 5,82 6,78 8,28 9,78 12,73 damax. 3,1 3,6 4,1 4,7 5,7 6,8 9,2 max. 1,80 2,00 2,40 2,60 3,30 3,9 5,0 k min. 1,66 1,86 2,26 2,46 3,12 3,6 4,7 r min. 0,1 0,1 0,1 0,2 0,2 0,25 0,4 x max. 1,1 1,25 1,5 1,75 2 2,5 3,2 Recess No. 1 2 2 2 2 3 3 m ref. 2,7 3,5 3,8 4,1 4,8 6,

30、2 7,7 min. 1,20 0,86 1,15 1,45 2,14 2,25 3,73 Type H Penetration max. 1,62 1,43 1,73 2,03 2,73 2,86 4,36 m ref. 2,4 3,5 3,7 4,0 4,6 6,1 7,5 min. 1,10 1,22 1,34 1,60 2,26 2,46 3,88 Cross recess Type Z Penetration max. 1,35 1,47 1,80 2,06 2,72 2,92 4,34 lcnom. min. max. Approximate mass in kilograms p

31、er 1 000 pieces (r = 7,85 kg/dm3) (for information only) 2 1,8 2,2 3 2,8 3,2 0,272 4 3,76 4,24 0,302 0,515 5 4,76 5,24 0,332 0,560 0,786 1,09 6 5,76 6,24 0,362 0,604 0,845 1,17 2,06 8 7,71 8,29 0,422 0,692 0,966 1,33 2,20 3,56 10 9,71 10,29 0,482 0,780 1,08 1,47 2,55 3,92 7,85 12 11,65 12,35 0,542 0

32、,868 1,20 1,63 2,80 4,27 8,49 16 15,65 16,35 0,662 1,04 1,44 1,95 3,30 4,98 9,77 20 19,58 20,42 0,782 1,22 1,68 2,25 3,78 5,69 11,0 25 24,58 25,42 0,932 1,44 1,98 2,64 4,40 6,56 12,6 30 29,58 30,42 1,66 2,28 3,02 5,02 7,45 14,2 35 34,5 35,5 2,57 3,41 5,62 8,25 15,8 40 39,5 40,5 3,80 6,25 9,20 17,4 4

33、5 44,5 45,5 6,88 10,0 18,9 50 49,5 50,5 7,50 10,9 20,6 60 59,05 60,95 12,7 23,7 70 69,05 70,95 26,8 80 79,05 80,95 29,8 NOTE Preferred lengths are those between the solid, bold, stepped lines. aThe size in parentheses should be avoided, if possible. bP is the pitch of the thread. cScrews with nomina

34、l lengths above the discontinuous line are threaded up to the head (b = l a). BS EN ISO 7048:2011ISO 7048:2011(E) 4 ISO 2011 All rights reserved4 Requirements and reference International Standards See Table 2. Table 2 Requirements and reference International Standards Material Steel Stainless steel

35、Non-ferrous metal General requirements International Standard ISO 8992 Tolerance class 6g Thread International Standard ISO 261, ISO 965-2 Property class 4.8, 5.8 A2-70 Mechanical propertyaInternational Standard ISO 898-1 ISO 3506-1 Materials are specified in ISO 8839. Product grade A Tolerance Inte

36、rnational Standard ISO 4759-1 Cross recesses ISO 4757 As processed As processed As processed Requirements for electroplating are specified in ISO 4042. Requirements for electroplating are specified in ISO 4042. Requirements for non-eletrolytically applied zinc flake coatings are specified in ISO 106

37、83.Finish Coating Additional requirements or other finishes or coatings shall be agreed between the supplier and the purchaser. Surface integrity Limits for surface discontinuities are specified in ISO 6157-1. Acceptability Acceptance inspection is specified in ISO 3269. aTo meet the requirements of

38、 the torsional test, fracture shall occur in the shank or the thread of the screw and not in the junction of the head and shank or the junction of the shank and recess. 5 Designation EXAMPLE A cross-recessed cheese head screw with thread M5, nominal length l = 20 mm, property Class 4.8 and cross rec

39、ess type Z is designated as follows: Cheese head screw ISO 7048 - M5 20 - 4.8 - Z BS EN ISO 7048:2011ISO 7048:2011(E) ISO 2011 All rights reserved 5Bibliography 1 ISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose bolts 2 ISO 1207, Slotted cheese head screws Pro

40、duct grade A This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international l

41、evel. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure

42、 that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsib

43、le, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20

44、8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (

45、0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand interna

46、tional standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are

47、 kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standa

48、rds via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not pr