EN ISO 6141-2015 en Gas analysis - Contents of certificates for calibration gas mixtures《气体分析 标定混合气体的合格证书内容(ISO 6141 2015)》.pdf

《EN ISO 6141-2015 en Gas analysis - Contents of certificates for calibration gas mixtures《气体分析 标定混合气体的合格证书内容(ISO 6141 2015)》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 6141-2015 en Gas analysis - Contents of certificates for calibration gas mixtures《气体分析 标定混合气体的合格证书内容(ISO 6141 2015)》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 6141:2015Gas analysis Contents ofcertificates for calibration gasmixturesBS EN ISO 6141:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 6141:2015.It supersedes BS EN ISO 6141:2006 which is withdrawn.The UK participatio

2、n in its preparation was entrusted to TechnicalCommittee PTI/15, Natural Gas and Gas Analysis.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible

3、 for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 79550 3ICS 71.040.40Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy

4、 and Strategy Committee on 31 March 2015.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6141 March 2015 ICS 71.040.40 Supersedes EN ISO 6141:2006English Version Gas analysis - Contents of certificates for calibration gas mixtures (ISO 61

5、41:2015) Analyse des gaz - Contenu des certificats des mlanges de gaz pour talonnage (ISO 6141:2015) Gasanalyse - Inhalte von Zertifikaten fr Kalibriergasgemische (ISO 6141:2015) This European Standard was approved by CEN on 26 December 2014. CEN members are bound to comply with the CEN/CENELEC Inte

6、rnal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any

7、 CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official ve

8、rsions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway

9、, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploit

10、ation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6141:2015 EBS EN ISO 6141:2015EN ISO 6141:2015 (E) 3 Foreword This document (EN ISO 6141:2015) has been prepared by Technical Committee ISO/TC 158 “Analysis of gases”. This European Standard shall be give

11、n the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2015, and conflicting national standards shall be withdrawn at the latest by September 2015. Attention is drawn to the possibility that some of the elements of this document

12、may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 6141:2006. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound

13、 to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

14、 Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 6141:2015 has been approved by CEN as EN ISO 6141:2015 without any modification. BS EN ISO 6141:2015ISO 6141:2015(E)Foreword iv1 Scope . 12 Normative references 13 Terms and de

15、finitions . 14 Contents . 14.1 Specification of certificate data 14.2 General information . 24.2.1 Title of the document . 24.2.2 Unique certificate identification . 24.2.3 Container identification . 24.2.4 Producer 24.2.5 Customer (optional) 34.2.6 Nominal composition (optional) 34.2.7 Authorizatio

16、n date 34.2.8 Responsible person . 34.2.9 Number of pages and page numbering 34.2.10 Intended use 34.2.11 Safety information 34.3 Gas or gas mixture specification 34.3.1 Specified components . 34.3.2 Composition . 34.3.3 Standard uncertainty . 44.3.4 Expanded uncertainty . 44.3.5 References/metrolog

17、ical traceability 44.3.6 Method of preparation 44.3.7 Filling pressure 44.3.8 Method of analysis 44.3.9 Date of preparation 44.3.10 Minimum utilization pressure 44.3.11 Expiry date 54.3.12 Date of analysis (optional) 54.3.13 Commercial name (optional) 54.4 Additional product information . 54.4.1 Con

18、tainer volume 54.4.2 Filling quantity (optional) . 54.4.3 Valve outlet connection 54.4.4 Storage/utilization temperature 54.4.5 Indicative values (optional) 5Annex A (informative) Cross-references to ISO Guide 31 and ISO/IEC 17025 6Bibliography 7 ISO 2015 All rights reserved iiiContents PageBS EN IS

19、O 6141:2015ISO 6141:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested

20、in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commi

21、ssion (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents sh

22、ould be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for

23、identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the co

24、nvenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Forewo

25、rd - Supplementary informationThe committee responsible for this document is ISO/TC 158, Analysis of gases.This fourth edition cancels and replaces the third edition (ISO 6141:2000), which has been technically revised to align it with ISO Guide 313.iv ISO 2015 All rights reservedBS EN ISO 6141:2015G

26、as analysis Contents of certificates for calibration gas mixtures1 ScopeThis International Standard specifies minimum requirements for the contents of certificates for homogeneous gas mixtures in gas cylinders to be used as calibration gas mixtures. Pure gases, when used as calibration gas mixtures,

27、 are also covered by this International Standard. Gases and gas mixtures produced for other purposes are not considered.The requirements in this International Standard deal with the metrological aspects of calibration gas mixtures. Other aspects, such as safety and legislative aspects, are not cover

28、ed.Furthermore, it specifies additional information (optional data) recommended for describing a homogeneous gas mixture, supplied under pressure in a cylinder or other container. It does not cover the field of safety-relevant data and related labelling.2 Normative referencesThe following documents,

29、 in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO/IEC Guide 98-3, Uncertainty

30、of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)ISO 7504, Gas analysis Vocabulary3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO/IEC Guide 98-3, ISO 7504, and the following apply.3.1producerorganization that has

31、produced the gas or gas mixtureNote 1 to entry: The producer is the organization which bears the responsibility for the contents of the certificate.3.2customerorganization that has ordered the gas or gas mixture3.3containervessel in which the gas or gas mixture is supplied4 Contents4.1 Specification

32、 of certificate dataThe information specified by this International Standard shall be provided by the supplier of the gas or gas mixture, in a certificate, i.e. a document uniquely related to the container and its contents.INTERNATIONAL STANDARD ISO 6141:2015(E) ISO 2015 All rights reserved 1BS EN I

33、SO 6141:2015ISO 6141:2015(E)The certificate shall contain as a minimum the data specified as “mandatory” in Table 1. It is recommended that the data specified as “optional” are also included in the certificate.Requirements for and explanations of the data to be provided are given in the following cl

34、auses.Table 1 Specification of certificate dataMandatory data Reference Optional data ReferenceTitle of the document 4.2.1 Customer 4.2.5Unique certificate identification 4.2.2 Nominal composition 4.2.6Container identification 4.2.3 Intended use 4.2.10Producer 4.2.4 Safety information 4.2.11Authoriz

35、ation date 4.2.7 Standard uncertainty 4.3.3Responsible person 4.2.8 Method of preparation 4.3.6Number of pages and page num-bering4.2.9 Method of analysis 4.3.8Specified components 4.3.1 Date of preparation 4.3.9Composition 4.3.2 Date of analysis 4.3.12Expanded uncertainty 4.3.4 Commercial name 4.3.

36、13References/metrological trace-ability4.3.5 Container volume 4.4.1Filling pressure 4.3.7 Filling quantity 4.4.2Minimum utilization pressure 4.3.10 Indicative values 4.4.5Expiry date 4.3.11Valve outlet connection 4.4.3Storage/utilization tempera-ture4.4.44.2 General information4.2.1 Title of the doc

37、umentThe certificate shall have a title that identifies the document as a certificate stating one or more properties of a gas or gas mixture.4.2.2 Unique certificate identificationEach certificate shall be assigned a unique identification.4.2.3 Container identificationContainers for pressurized gase

38、s shall be identified by the number that is stamped into the wall or by batch or lot numbers.4.2.4 ProducerProvide the name, address, telephone number and e-mail address of the producer.2 ISO 2015 All rights reservedBS EN ISO 6141:2015ISO 6141:2015(E)4.2.5 Customer (optional)Provide the name and add

39、ress of the customer and any other information required by the customer.NOTE ISO/IEC 17025:20052requires mentioning the customer on a certificate.4.2.6 Nominal composition (optional)Provide the composition of the gas or gas mixture requested by the customer.NOTE A quality indication of the gases use

40、d in preparation can be appropriate.4.2.7 Authorization dateThe date the certificate was issued shall be stated.4.2.8 Responsible personThe signature and name of the person who is responsible for the information in the certificate shall be given.4.2.9 Number of pages and page numberingThe total numb

41、er of pages of the certificate shall be given. The pages of the document shall be numbered consecutively.4.2.10 Intended useState the application(s) for which the gas or gas mixture can be used.NOTE The specification of these applications is not necessarily exhaustive.EXAMPLE “This gas mixture can b

42、e used for calibration of equipment.”4.2.11 Safety informationInformation relevant for the safe handling, transport, and storage should be provided.NOTE This kind of information is usually given by a safety data sheet (SDS). If further information is required, this may be provided on the calibration

43、 gas or gas mixture certificate.4.3 Gas or gas mixture specification4.3.1 Specified componentsThe names of the specified components of the gas mixture shall be given in an unambiguous way that is understood by the customer. It is recommended to name the components in accordance with IUPAC terminolog

44、y. For the balance gas, a more common name may be used, such as synthetic air.4.3.2 CompositionThe contents of all specified components of the gas mixture shall be given.NOTE It is preferable to express the contents in amount-of-substance or mass fractions, since these quantities are independent of

45、the pressure and the temperature of the gas mixture. If other quantities are used, e.g. mass concentration or volume fraction, it is necessary to specify the conditions (pressure and temperature) for which the stated composition is valid. ISO 2015 All rights reserved 3BS EN ISO 6141:2015ISO 6141:201

46、5(E)4.3.3 Standard uncertaintyFor every specified component, it shall be possible to deduce the standard uncertainty from the uncertainty information provided.EXAMPLE The standard uncertainty can be calculated from a stated expanded uncertainty and coverage factor.The standard uncertainty should inc

47、lude the contributions from all relevant uncertainty sources. The uncertainty sources considered in the evaluation may be specified. The supplier should be ready and able to provide additional information on the evaluation of uncertainty at request of the customer.4.3.4 Expanded uncertaintyFor every

48、 specified component, the expanded uncertainty of the content shall be stated. The coverage factor used shall be specified. Preferably, the information is supplemented by the assumed probability distribution and the level of coverage.It is recommended to use a coverage factor of 2.4.3.5 References/m

49、etrological traceabilityReferences shall be given, relating the stated contents and uncertainties to International Standard methods.For the components contents specified, the metrological traceability information shall be given, including the used measurement standards or certified reference materials.The supplier shall specify to the customer, on request, the relevant metrological traceability chains.4.3.6 Method of preparationSpecify the essential features of the method by which the gas or gas mixture was produced.4.3.7 Filling pressureProvide th