EN ISO 5356-2-2012 en Anaesthetic and respiratory equipment - Conical connectors - Part 2 Screw-threaded weight-bearing connectors《麻醉和呼吸设备 锥形连接器 第2部分 Screw-threaded负重连接器》.pdf

《EN ISO 5356-2-2012 en Anaesthetic and respiratory equipment - Conical connectors - Part 2 Screw-threaded weight-bearing connectors《麻醉和呼吸设备 锥形连接器 第2部分 Screw-threaded负重连接器》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 5356-2-2012 en Anaesthetic and respiratory equipment - Conical connectors - Part 2 Screw-threaded weight-bearing connectors《麻醉和呼吸设备 锥形连接器 第2部分 Screw-threaded负重连接器》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 5356-2:2012Anaesthetic and respiratoryequipment ConicalconnectorsPart 2: Screw-threaded weight-bearingconnectors (ISO 5356-2:2012)BS EN ISO 5356-2:2012 BRITISH STANDARD

2、National forewordThis British Standard is the UK implementation of EN ISO5356-2:2012. It supersedes BS EN ISO 5356-2:2007 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee CH/121/1, Breathing attachments and anaestheticmachines.A list of organizations repr

3、esented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580

4、78147 6ICS 11.040.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME E

5、UROPENNE EUROPISCHE NORM EN ISO 5356-2 November 2012 ICS 11.040.10 Supersedes EN ISO 5356-2:2007English Version Anaesthetic and respiratory equipment - Conical connectors - Part 2: Screw-threaded weight-bearing connectors (ISO 5356-2:2012) Matriel danesthsie et de ranimation respiratoire - Raccords

6、coniques - Partie 2: Raccords vis pouvant supporter un certain poids (ISO 5356-2:2012) Ansthesie- und Beatmungsgerte - Konische Konnektoren - Teil 2: Gewichtstragende Konnektoren mit Schraubgewinde (ISO 5356-2:2012) This European Standard was approved by CEN on 14 November 2012. CEN members are boun

7、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CE

8、N-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre h

9、as the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L

10、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012

11、CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 5356-2:2012: EBS EN ISO 5356-2:2012EN ISO 5356-2:2012 (E) 3 Foreword This document (EN ISO 5356-2:2012) has been prepared by Technical Committee ISO/TC 121 “Anaesthetic and respir

12、atory equipment“ in collaboration with Technical Committee CEN/TC 215 “Respiratory and anaesthetic equipment” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest

13、by May 2013, and conflicting national standards shall be withdrawn at the latest by November 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such pa

14、tent rights. This document supersedes EN ISO 5356-2:2007. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, F

15、inland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text o

16、f ISO 5356-2:2012 has been approved by CEN as a EN ISO 5356-2:2012 without any modification. BS EN ISO 5356-2:2012ISO 5356-2:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Inter

17、national Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison wit

18、h ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical

19、committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to th

20、e possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 5356-2 was prepared by Technical Committee ISO/TC 121, Anaesthetic and respiratory equipment, Subcommittee SC 1, Breathing

21、 attachments and anaesthetic machines.This third edition cancels and replaces the second edition (ISO 5356-2:2006), which has been revised by rewording the scope and by incorporating minor editorial modifications.ISO 5356 consists of the following parts, under the general title Anaesthetic and respi

22、ratory equipment Conical connectors: Part 1: Cones and sockets Part 2: Screw-threaded weight-bearing connectors ISO 2012 All rights reserved iiiBS EN ISO 5356-2:2012ISO 5356-2:2012(E)IntroductionWhereas the conical connectors specified in ISO 5356-1 are satisfactory for lightweight breathing attachm

23、ents, there is also a need for more substantial connectors to support heavy or fragile components. Factors governing the design of these connectors include robustness, simplicity, ease of sterilization and ease of engagement and disengagement by hand. They should also be compatible with connectors m

24、eeting the requirements specified in ISO 5356-1 and should, if possible, eliminate the likelihood of inadvertent misconnection, although it has to remain the responsibility of the user to check that any system in which they are used is correctly assembled before use.Screw-threaded weight-bearing con

25、nectors specified in this part of ISO 5356 can be used for attachments within the breathing system and at the common gas outlet.iv ISO 2012 All rights reservedBS EN ISO 5356-2:2012Anaesthetic and respiratory equipment Conical connectors Part 2: Screw-threaded weight-bearing connectors1 ScopeThis par

26、t of ISO 5356 specifies dimensional requirements for screw-threaded weight-bearing conical connectors intended for use with inhalation anaesthesia apparatus and ventilators. Such connectors are intended for mounting heavy accessories.This part of ISO 5356 specifies requirements for the following scr

27、ew-threaded, weight-bearing conical connectors: 22 mm connectors; 22 mm/15 mm coaxial connectors.Requirements for the application of screw-threaded, weight-bearing conical connectors are not included in this part of ISO 5356, but are or will be given in the relevant International Standards for speci

28、fic medical devices and accessories.NOTE Requirements on cones and sockets are specified in ISO 5356-1.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the la

29、test edition of the referenced document (including any amendments) applies.ISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium qualityISO 5356-1:1), Anaesthetic and respiratory equipment Conical connect

30、ors Part 1: Cones and sockets3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1inhalation anaesthesia apparatusequipment intended for dispensing and delivering anaesthetic gases and vapours into a breathing system for delivery to the patient3.2bre

31、athing attachmentcomponent(s) intended to make up or complete a breathing systemNOTE Adapted from ISO 4135:2001, definition 4.1.6.1) To be published (Revision of ISO 5356-1:2004)INTERNATIONAL STANDARD ISO 5356-2:2012(E) ISO 2012 All rights reserved 1BS EN ISO 5356-2:2012ISO 5356-2:2012(E)3.3breathin

32、g systemthose gas pathways continuously or intermittently in communication with the patients respiratory tract during any form of ventilationNOTE 1 In practice, a breathing system usually extends froma) the point of supply of a controlled gas mixture, e.g. the common gas outlet of an anaesthetic mac

33、hine (in some situations, particularly in lung ventilators, the point of supply may be inside a piece of equipment and should not be confused with a connection port fitted elsewhere, for example on the casing of a ventilator), orb) the fresh-gas inlet of a circle system, lung ventilator, T-piece, et

34、c., orc) the fresh-gas inlet of a manually operated resuscitator.NOTE 2 It usually extends to the point at which the gas mixture escapes into the atmosphere or a gas scavenging system, for example from an APL valve, the open end of a T-piece, etc.NOTE 3 Gas pathways exclusively concerned with gas sc

35、avenging systems are not regarded as part of the breathing system.NOTE 4 Adapted from ISO 4135:2001, definition 4.1.1. 4 DesignThe dimensions of the components of screw-threaded weight-bearing connectors shall be as shown in Figure 1.The free axial movement of the union nut on the female component s

36、hall be not more than 2 mm in order that, when the connectors are unscrewed, the male and female components shall be forced apart.All male screw threads shall be M33 2, 6g, and all female screw threads shall be M33 2, 6H, in accordance with ISO 965-2.Dimensions in millimetresa) Male component2 ISO 2

37、012 All rights reservedBS EN ISO 5356-2:2012ISO 5356-2:2012(E)b) Female component Parallel socket (only essential dimensions shown)ac) Female component Taper and socket (only essential dimensions shown)ad) Union nut (only essential dimensions shown)b ISO 2012 All rights reserved 3BS EN ISO 5356-2:20

38、12ISO 5356-2:2012(E)e) Typical female component assemblybKey1 male 22 mm cone or 22 mm/15 mm coaxial as specified in ISO 5356-1 male 22 mm cone as specified in Figure 2 a) of ISO 5356-1:2 male screw thread3 O-ring groove recommended size 24,8 mm diameter (2,3 + 0,2/0) mm width to suit an O-ring of r

39、ecommended size 22,1 mm internal diameter and 1,6 mm cross-section4 22 mm female conical socket as specified in ISO 5356-15 knurling6 female screw thread7 position of retaining lug, shoulder or circlip8 retaining shouldera18 mm diameter intended for use within breathing systems.bThe union nut may be

40、 retained by a circlip in place of a shoulder.Figure 1 Components for screw-threaded, weight-bearing connectors4 ISO 2012 All rights reservedBS EN ISO 5356-2:2012ISO 5356-2:2012(E)Bibliography1 ISO 262, ISO general-purpose metric screw threads Selected sizes for screws, bolts and nuts2 ISO 4135:2001

41、, Anaesthetic and respiratory equipment Vocabulary ISO 2012 All rights reserved 5This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It p

42、resents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London

43、W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and

44、services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0

45、)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may b

46、uy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to order

47、s for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +4

48、4 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and ot