EN ISO 3611-2010 en Geometrical product specifications (GPS) - Dimensional measuring equipment Micrometers for external measurements - Design and metrological characteristics《产品几何技.pdf

《EN ISO 3611-2010 en Geometrical product specifications (GPS) - Dimensional measuring equipment Micrometers for external measurements - Design and metrological characteristics《产品几何技.pdf》由会员分享，可在线阅读，更多相关《EN ISO 3611-2010 en Geometrical product specifications (GPS) - Dimensional measuring equipment Micrometers for external measurements - Design and metrological characteristics《产品几何技.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 3611:2010Geometrical productspecifications (GPS) Dimensional measuringequipment: Micrometersfor external measurements Design and metrologicalcharacteristics (ISO 3611:2010)BS EN ISO 3611:2010Incorporating corrigendum October 2015BS EN ISO 3611:2010 BRITISH STANDARD

2、National forewordThis British Standard is the UK implementation of EN ISO 3611:2010. It partially supersedes BS 870:2008.BS 870:2008 will remain current for the foreseeable future as it can be used as guidance to specify the metrological characteristics when completing the data sheet presented in An

3、nex B of EN ISO 3611.The UK participation in its preparation was entrusted by Technical Committee TDW/4, Technical Product Realization, to Subcommittee TDW/4/4, Technical Product Realization - Gauging and Measurement Equipment.A list of organizations represented on this subcommittee can be obtained

4、on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015ISBN 978 0 580 92205 3ICS 17.040.30Compliance with a

5、British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2011.Amendments/corrigenda issued since publicationDate Text affected31 October 2015 Supersession information in National

6、foreword updatedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 3611 November 2010 ICS 17.040.30 English Version Geometrical product specifications (GPS) - Dimensional measuring equipment: Micrometers for external measurements -Design and metrological characteristics (ISO 3611:2010) Spcific

7、ation gomtrique des produits (GPS) - quipement de mesurage dimensionnel: Micromtres dextrieur - Caractristiques de conception et caractristiques mtrologiques (ISO 3611:2010) Geometrische Produktspezifikation (GPS) - Lngenmessgerte: Bgelmessschrauben - Konstruktionsmerkmale und messtechnische Merkmal

8、e (ISO 3611:2010) This European Standard was approved by CEN on 11 September 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and

9、 bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the r

10、esponsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany

11、, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Ma

12、nagement Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3611:2010: EBS EN ISO 3611:2010EN ISO 3611:2010 (E) 3 Foreword This document (EN ISO 3611:2010) has been prepared by Techni

13、cal Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given th

14、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subje

15、ct of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bul

16、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notic

17、e The text of ISO 3611:2010 has been approved by CEN as a EN ISO 3611:2010 without any modification. BS EN ISO 3611:2010EN ISO 3611:2010 (E) 3 Foreword This document (EN ISO 3611:2010) has been prepared by Technical Committee ISO/TC 213 “Dimensionaland geometrical product specifications and verifica

18、tion” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorse

19、ment, at the latest by May 2011, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any

20、 or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greec

21、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 3611:2010 has been approved by CEN as a EN ISO 3611:2010 without any mo

22、dification. BS EN ISO 3611:2010EN ISO 3611:2010 (E) 3 Foreword This document (EN ISO 3611:2010) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification” in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical

23、product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn a

24、t the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the natio

25、nal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N

26、orway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 3611:2010 has been approved by CEN as a EN ISO 3611:2010 without any modification. BS EN ISO 3611:2010ISO 3611:2010(E) ISO 2010 All rights reserved iiiContents

27、Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Design characteristics 2 4.1 General design and nomenclature 2 4.2 Main dimensions .3 4.3 Types of indicating devices .3 4.3.1 General .3 4.3.2 Analogue indicating devices4 4.3.3 Digital indicating devices,

28、 with mechanical digital display 5 4.3.4 Digital indicating devices with electronic digital display6 4.4 Protection for field use .6 4.5 Frame7 4.6 Measuring faces 7 4.7 Measuring force limiting device.7 4.8 Adjustment devices.7 4.9 Design characteristics (manufacturers specification)7 5 Metrologica

29、l characteristics.8 5.1 General .8 5.2 Effect of spindle clamp .8 5.3 Maximum permissible error of indication (limited by MPE)8 5.3.1 General .8 5.3.2 Full surface contact error, J (limited by MPEJ) 8 5.3.3 Repeatability, R (limited by MPER).8 5.3.4 Partial surface contact error, E (limited by MPEE)

30、.8 5.4 Measuring forces (limited by MPL) 8 5.5 Instrument specification sheet 8 6 Proof of conformance with specifications9 7 Marking.9 Annex A (informative) Example of an error-of-indication curve 10 Annex B (informative) Example of data sheet for micrometers for external measurements11 Annex C (in

31、formative) Calibration of metrological characteristics12 Annex D (informative) Error tests13 Annex E (informative) Notes on use .15 Annex F (informative) Relation to the GPS matrix model.16 Bibliography18 BS EN ISO 3611:2010ISO 3611:2010(E) iv ISO 2010 All rights reservedForeword ISO (the Internatio

32、nal Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been

33、established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standar

34、dization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for v

35、oting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all s

36、uch patent rights. ISO 3611 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. This second edition cancels and replaces the first edition (ISO 3611:1978), which has been technically revised. BS EN ISO 3611:2010ISO 3611:2010(E) ISO 201

37、0 All rights reserved vIntroduction This International Standard is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences the chain link 5 of the chain of standards on size in the general GPS matrix. For more detailed info

38、rmation on the relation between this International Standard, other standards and the GPS matrix model, see Annex F. BS EN ISO 3611:2010BS EN ISO 3611:2010INTERNATIONAL STANDARD ISO 3611:2010(E) ISO 2010 All rights reserved 1Geometrical product specifications (GPS) Dimensional measuring equipment: Mi

39、crometers for external measurements Design and metrological characteristics 1 Scope This International Standard specifies the most important design and metrological characteristics of micrometers for external measurements: with analogue indication; with digital indication: mechanical or electronic d

40、igital display. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 14253-

41、1, Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with specifications ISO 14253-2, Geometrical product specifications (GPS) Inspection by measurement of workpieces and measurin

42、g equipment Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification ISO 14978:2006, Geometrical product specifications (GPS) General concepts and requirements for GPS measuring equipment IEC 60529, Degrees of protection

43、 provided by enclosures (IP Code) ISO/IEC Guide 98-3, Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) ISO/IEC Guide 99, International vocabulary of metrology Basic and general concepts and associated terms (VIM) 3 Terms and definitions For the purp

44、oses of this document, the terms and definitions given in ISO 14978, ISO/IEC Guide 99 and the following apply. BS EN ISO 3611:2010ISO 3611:2010(E) 2 ISO 2010 All rights reserved3.1 micrometer for external measurements measuring instrument which gives the evaluation of a dimensional quantity of an ex

45、ternal feature of a workpiece on the basis of movement of a spindle with a measuring face, moving relatively to a material measure and an anvil, with the movement generated by a screw thread NOTE 1 The guiding elements of the spindle and of the anvil are connected by a frame. NOTE 2 Usually, microme

46、ters for external measurements have a thread as a material measure with the anvil, spindle and material measure arranged in a line. 3.2 measuring face contact contact between the measuring face and a feature of a workpiece 3.2.1 full measuring face contact contact between the full area of the measur

47、ing face and a feature of a workpiece 3.2.2 partial measuring face contact contact between a partial area of the measuring face and a feature of a workpiece 4 Design characteristics 4.1 General design and nomenclature The general design and workmanship of the micrometer for external measurements sha

48、ll be such that its metrological characteristics comply with the requirements of this International Standard under all operational orientations, unless otherwise specified by the manufacturer. See Figure 1 for the general design. Key 1 measuring faces 7 sleeve 2 anvil 8 fiducial line 3 measuring spi

49、ndle 9 analogue indication 4 frame 10 thimble 5 thermally insulating plate 11 fast drive 6 spindle clamp Figure 1 Nomenclature and general design of a micrometer for external measurements BS EN ISO 3611:2010ISO 3611:2010(E) ISO 2010 All rights reserved 34.2 Main dimensions The micrometer for external measurements shall conform to the dimensions specified in Figure 2 and Table 1. Figure 2 Dimensions of a micrometer for external measurements Table 1 Dimensions of a micrometer for external measurements Dimension Nom