EN ISO 1264-1997 en Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride - Determination of pH of Aqueous Extract《塑料 氯乙烯的均聚物和共聚物树脂 水萃物的pH值测定 ISO 1264-1980》.pdf

《EN ISO 1264-1997 en Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride - Determination of pH of Aqueous Extract《塑料 氯乙烯的均聚物和共聚物树脂 水萃物的pH值测定 ISO 1264-1980》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 1264-1997 en Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride - Determination of pH of Aqueous Extract《塑料 氯乙烯的均聚物和共聚物树脂 水萃物的pH值测定 ISO 1264-1980》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 STD.BSI BS EN IS0 L2b4-ENGL 1997 Lb24bbS Ob4093b 401 BRITISH STANDARD Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of pH of aqueous extract The European Standard EN EO 1264 : 1997 has the status of a British Standard ICs 83.080.20 BS EN IS0 1264 : 1997 BS 2782 : Par

2、t4: Method 454C : 1997 -o n-m U- NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPRIGET LAW u u - STD-BSI BS EN IS0 L2b4-ENGL 1777 M LbZibb7 Ob40737 348 been prepared under the direction of the Sector Board for Materiais and Chemicals, was published under the authority of the Standaids Bo

3、ard and comes into effect on 15 September 1997 hd. No. O BSI 1997 ISBN O 680 28504 9 BS EN IS0 1264 : 1997 Da Text affected National foreword This British Standard is the English language version of EN IS0 1264 : 1997. It is identical with IS0 1264 : 1980. It supersedes BS 2782 : Part 4 ; Method 454

4、C : 1978 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRIEM, Vinyl chloride, which has the responsibility to: - aid enquirem to understand the text; - present to the responsible intematio - monitor related international and European developments an

5、d promulgate them in the UK. A list of organizations represented on this commit b) 50 I 2 ml of sodium chloride solution. Stopper the flask and place it on the shaker (4.51. Agitate rapid- ly for 60 i 5 min. Allow the flask to stand for 5 to 10 min to allow the resin to settle (below or on the surfa

6、ce of the liquid). Then, using the pipette (4.2). transfer approximately 30 to 40 ml of the liquid above or below the resin into the beaker (4.3), which has been rinsed beforehand with the sodium chloride solution. (in cases where a large amount of foam has been formed, filtering may be necessary be

7、fore pipetting.) Measure the pH of the aqueous solution at a temperature of 23 f2 OC by means of the pH meter (4.1). Carry out two determinations. Express the values in pH units to one decimal place. If the difference in duplicate determinations is greater than 0,2 pH units, carry out a further seri

8、es of deter- minations until agreement within this limit is obtained. 1 EN IS0 1264 : 1997 6 Expression of results 7 Test report Calculate the arithmetic mean of the two values finally retained, rounding to the first decimal place, according to the usual rules. The test report shall include the foll

9、owing particulars : a) reference to this International Standard; b) complete identification of the product tested; ci the result expressed according to clause 6; d) any circumstances which may have affected the result. NOTE - Co-operative tests have shown reproducibility between dif- ferent laborato

10、ries, on the values of pH thus determined, of f 0,3. Annex Recommended method for the de-activation of glassware Immerse the glassware in a 100 g/l hydrochloric acid solution for 2 days. Replace the hydrochloric acid with a fresh solution and allow to stand for a further 2 days. Wash copiously with

11、de-ionized water four or five times. Wash with distilled water three times. Dry in an oven at 120 OC for 24 h. 2 BS EN IS0 1264 : 1997 BS 2782 : Part 4 : Method 454C : 1997 BSI 389 Chiswick High Road London w4 4AL STDOBSI BS EN IS0 12b4-ENGL 1777 = Lb24bb9 Ob110744 588 BSI - British Standards Instit

12、ution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internaiional level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provision

13、s of a contract. Users of British Standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant ahn of BSI to improve the t

14、y of our products and services. We would be grateful if anyone finding an inaixuracy or ambiguity while using this British Standard would inform the Secretary of the responsible technical committee, the identity of which cm be found on the inside front cover. Tel 0181 996 9000; Fax: 0181 996 7400. B

15、SI offers members an indiviual updating service called PLUS which ems that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign sandards publications should be addressed to Customer Services, Sales Department at Chiswick T

16、el: 0181 996 7000, Fax 0181 996 7001. in response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national

17、, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (l3lTS) and its Technicai Help to Exporters Service. Contact the Informaton Department at Chiswick Tel 0181 996 7111; Fax 0181 996 7048. Subscribing members of BSI are kept u

18、p to date with standards developments and receive substantiai discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tek 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also

19、holds the copyright, in the lJK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, re

20、cording or otherwise - without prior written permission hm BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. if these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained fiom the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4&