EN ISO 1120-2012 en Conveyor belts - Determination of strength of mechanical fastenings - Static test method《传送带 机械连接件强度测定静态测试方法》.pdf

《EN ISO 1120-2012 en Conveyor belts - Determination of strength of mechanical fastenings - Static test method《传送带 机械连接件强度测定静态测试方法》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 1120-2012 en Conveyor belts - Determination of strength of mechanical fastenings - Static test method《传送带 机械连接件强度测定静态测试方法》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConveyor belts Determination of strength of mechanical fastenings Static test methodBS EN ISO 1120:2012National forewordThis British Standard is the UK implementation of EN ISO 1

2、120:2012. It super-sedes BS EN ISO 1120:2002 which is withdrawn.The UK participation in its preparation was entrusted to Technical CommitteePRI/67, Conveyor belts.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to inc

3、lude all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 77356 3ICS 53.040.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This Brit

4、ish Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 November 2012.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN ISO 1120:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1120 October 2012 ICS 53.040.20 S

5、upersedes EN ISO 1120:2002English Version Conveyor belts - Determination of strength of mechanical fastenings - Static test method (ISO 1120:2012) Courroies transporteuses - Dtermination de la rsistance des assemblages agrafs - Mthode dessai statique (ISO 1120:2012) Frdergurte - Bestimmung der Festi

6、gkeit mechanischer Verbindungen - Statisches Prfverfahren (ISO 1120:2012)This European Standard was approved by CEN on 30 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nationa

7、l standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A versio

8、n in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Cze

9、ch Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. E

10、UROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1120:2012: EBS EN ISO

11、 1120:2012EN ISO 1120:2012 (E) 2 Contents Page Foreword 3BS EN ISO 1120:2012EN ISO 1120:2012 (E) 3 Foreword This document (EN ISO 1120:2012) has been prepared by Technical Committee ISO/TC 41 “Pulleys and belts (including veebelts)“ in collaboration with Technical Committee CEN/TC 188 “Conveyor belt

12、s” the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention

13、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1120:2002. According to the CEN/CENELEC Internal Regulations, t

14、he national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv

15、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1120:2012 has been approved by CEN as a EN ISO 1120:2012 without any modification. BS EN ISO 1120:2012IS

16、O 1120:2012(E) ISO 2012 All rights reserved iiiContents Page1 Scope 12 Normative references . 13 Terms and definitions . 14 Principle . 25 Apparatus 26 Test piece . 26.1 Selection of test piece 26.2 Shape, dimensions and preparation 36.3 Number of test pieces 36.4 Conditioning and test conditions 37

17、 Procedure 37.1 For mechanical belt joints with a connecting rod 37.2 For mechanical belt joints without a connecting rod . 48 Expression of results . 49 Test report . 5Bibliography . 7BS EN ISO 1120:2012INTERNATIONAL STANDARD ISO 1120:2012(E)Conveyor belts Determination of strength of mechanical fa

18、stenings Static test method1 ScopeThis International Standard specifies a static test method for measuring the strength of a conveyor belt mechanical fastening; the mechanical joints can be either of the type employing a connecting rod or of a type which does not employ a connecting rod.This Interna

19、tional Standard does not cover vulcanized joints.This International Standard is neither applicable to nor valid for light conveyor belts, as described in ISO 21183-1.NOTE The purpose of the test specified in this International Standard is to eliminate mechanical fastenings of insufficient static str

20、ength. It is intended to establish a dynamic test at a later date.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

21、nt (including any amendments) applies.ISO 283, Textile conveyor belts Full thickness tensile strength, elongation at break and elongation at the reference load Test method3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1width of fasteningnumber o

22、f units multiplied by the pitch, or number of hooks multiplied by the pitch3.2pitchdistance between a point on a unit or hook and the corresponding point on the next unit or hook, according to the type of fasteningSee Figure 1. ISO 2012 All rights reserved 1BS EN ISO 1120:2012ISO 1120:2012(E)1122a)

23、Width of fastening equal to the pitch times eightb) Width of fastening equal to the pitch times threeKey1 pitch2 width of fasteningFigure 1 Pitch and width of fastenings of mechanical fastenings4 PrincipleApplication of an increasing tensile force to a test piece until the joint made by the mechanic

24、al fastening breaks and comes apart.5 Apparatus5.1 Metallic adapter plate for joints which employ a connecting rod that can be disconnected.5.2 Dynamometer, as described in ISO 283.6 Test piece6.1 Selection of test pieceTest pieces shall be taken parallel to the axis of the belt and at least 50 mm f

25、rom its edge.2 ISO 2012 All rights reservedBS EN ISO 1120:2012ISO 1120:2012(E)6.2 Shape, dimensions and preparation6.2.1 Mechanical belt joints with connecting rodThe test pieces shall consist of a full thickness piece of belting cut in the longitudinal direction, with a minimum length of 100 mm plu

26、s the gripped length (see Figure 2), and a width of 150 mm. The test piece shall be connected to the connecting plate by the mechanical fastener. The fastening width shall be at least 100 mm.6.2.2 Mechanical belt joints without connecting rodThe test piece shall consist of two lengths of belting, ea

27、ch of minimum length of 100 mm plus the gripped length (see Figure 2), and 150 mm wide, assembled by means of the mechanical fastening to be used, not less than 100 mm wide.6.2.3 Overall width of fastening/number of hooksThe overall width of fastening shall be not less than 100 mm. To determine the

28、number of hooks, use the formula:100 divided by the Pitch equal to the Number, rounded to the next whole number.The overall width of fastening is: the pitch times the number of hooks.EXAMPLEPitch of one hook: 14 mmDetermination of the number of hooks: 100/14 mm = 7,1 (rounded to 8)Overall width of f

29、astening: 14 mm 8 = 112 mm.6.3 Number of test piecesThree test pieces shall be tested.6.4 Conditioning and test conditionsThe tests shall start not less than 24 h after manufacturing. This time includes 8 h for conditioning at one of the temperatures specified. (23 2) C or (20 2) C for temperate tem

30、perature control only; (27 2) C for tropical temperature control only.The tests shall be conducted at the same temperature as used for conditioning. A certain humidity for conditioning and testing is not required.The temperature at which the test pieces were conditioned and tested shall be recorded

31、in the test report.In the event of dispute, the conditioning period shall be 72 h.7 Procedure7.1 For mechanical belt joints with a connecting rodFasten the test piece in one of the grips of the dynamometer and attach the adapter plate to the belt at the distance between grips as shown in Figure 2.Ex

32、ert the tensile force such that it is applied symmetrically, i.e. that there is no tendency to start rupture at one end of the joint. ISO 2012 All rights reserved 3BS EN ISO 1120:2012ISO 1120:2012(E)Separate the grips at a rate of (100 10) mm/min; record the maximum force before the mechanical faste

33、ning breaks.7.2 For mechanical belt joints without a connecting rodFasten the ends of the test piece in the grips of the dynamometer as shown in Figure 2.Exert the tensile force such that it is applied symmetrically, i.e. that there is no tendency to start rupture at one end of the joint.Separate th

34、e grips at a rate of (100 10) mm/min. Record the maximum force before the mechanical fastening breaks.8 Expression of resultsDetermine the mean of the values obtained and calculate:a) the average breaking strength of the fastening, in newtons per millimetre width of fastening (see Figures 1 and 2);b

35、) the strength of the fastening, expressed as a percentage of the full thickness nominal tensile strength (see ISO 283-1:2000).4 ISO 2012 All rights reservedBS EN ISO 1120:2012ISO 1120:2012(E)9 Test reportThe test report shall include the following information:a) the width of fastening;b) the brand

36、and type of fastener;c) the brand and the type of conveyor belt;d) the results obtained;e) the type of failure of the fastening, e.g. whether the belt is torn or whether the fastener is broken;f) the temperature of conditioning and testing (see 6.4). ISO 2012 All rights reserved 5BS EN ISO 1120:2012

37、ISO 1120:2012(E)Dimensions in millimetres 10015012345678910Key1 dynamometer grip2 pivot (optional)3 adaptor plate4 rod5 half-fastening6 pitch7 test piece of belt8 width of fastening9 dynamometer grip10 gripped lengthFigure 2 Layout for static test6 ISO 2012 All rights reservedBS EN ISO 1120:2012ISO

38、1120:2012(E)Bibliography1 ISO 21183-1, Light conveyor belts Part 1: Principal characteristics and applications ISO 2012 All rights reserved 7BS EN ISO 1120:2012This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Sta

39、ndards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standard

40、s Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or edi

41、tions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside

42、 frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Te

43、l: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Servic

44、es.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on nat

45、ional, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other

46、benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the da

47、ta, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI

48、for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI mu