EN 62053-61-1998 en Electricity Metering Equipment (a c ) Particular Requirements Part 61 Power Consumption and Voltage Requirements《交流电测量设备 特殊要求 第61部分 功率消耗和电压要求 IEC 62053-61 1998》.pdf

《EN 62053-61-1998 en Electricity Metering Equipment (a c ) Particular Requirements Part 61 Power Consumption and Voltage Requirements《交流电测量设备 特殊要求 第61部分 功率消耗和电压要求 IEC 62053-61 1998》.pdf》由会员分享，可在线阅读，更多相关《EN 62053-61-1998 en Electricity Metering Equipment (a c ) Particular Requirements Part 61 Power Consumption and Voltage Requirements《交流电测量设备 特殊要求 第61部分 功率消耗和电压要求 IEC 62053-61 1998》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-BSI BS EN b2053-bL-ENGL 1777 81 lb24bb7 0743C72 503 BRITISH STANDARD Electricity metering equipment (a.c.) - Particular requirements - Part 61: Power consumption and voltage requirements The European Standard EN 6205361:1998 has the status of a British Standard ICs 91.140.50 NO COPYING WITHOUT

2、BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 62053-6k1999 IEC 62053-611998 STD-BSI BS EN b2053-bL-ENGL 1999 I Lb24bbS O743572 44T BS EN 62063-61:1999 National foreword This British Standard is the English language version of EN 62053-61: 1998. It is identical with IEC 6205361: 1998. The

3、 UK participation in its preparation was entrusted to Technical Committee PEU13, Electricity meters, which has the responsibility to: - aid enquirers to understand the tea - present to the responsible international/European committee any enquiries on the interpretation, or proposais for change, and

4、keep the UK interests informed them in the UK. - monitor related international and European developments and promulgate A list of organizations represented on this committee cm be obtained on request to its secretary. Rom 1 January 1997, all IEC publications have the number 60000 added to the old nu

5、mber. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include

6、 an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards

7、Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard do

8、es not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. This British Standard, having Amendments issued since publication direction of the Electrotc

9、hnical been prepared under the Sedor Committee, was published under the authority of the Standards Committee and comes into effect on 15 January 1999 O BSI 01-1999 l ISBN O 580 32040 5 i Text affected EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62053-61 April 1998 ICs 91.140.50 Descriptors:

10、 Electricity metering, static meter. multianergy meter. multi-function meter, power consumption, voltige requirements English version Electricity metering equipment (a.c.) Particular requirements Part 61 : Power consumption and voltage requirements (IEC 62053-61 :1998) Equipement de comptage de llec

11、tricit (c.a.1 - Prescriptions particulires Partie 61 : Puissance absorbe et prescriptions de tension (CE1 62053-61 : 1 998) Einrichtungen zur Messung der elektrischen Energie (AC) Besondere Anforderungen Teil 61 : Leistungsaufnahme und Spannungsanforderungen (IEC 62053-61 : 1998) This European Stand

12、ard was approved by CENELEC on 1998-04-01. CENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerni

13、ng such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its

14、 own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France. Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, P

15、ortugal, Spain. Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electtotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fur Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels - 1998 CENELEC - Ali ri

16、ghts of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 62053-61:1998 E STD-ES1 BS EN b2053-bl-ENGL 1999 1b24bbS 0743574 212 Page 2 EN 62053-61:1998 Foreword The text of document 1311 135/FDIS, future edition 1 of IEC 61 899, prepared by IEC TC 13, Equip

17、ment for electrical energy measurement and load control, was submitted to the IEC- CENELEC parallel vote. The document was published by IEC as IEC 62053-61 and was approved by CENELEC as EN 62053-61 on 1998-04-01. The following dates were fixed: - latest date by which the EN has to be implemented at

18、 national level by publication of an identical national standard or by endorsement (dop) 1999-01 -01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dw) 2001-01-01* This standard is to be used in conjunction with EN 61 036. Annexes designated “normative“ a

19、re part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 62053-61 : 1998 was approved by CENELEC as a European Standard without any modification. STD-BSI BS EN bZU53-bL-ENGL 1777 1h

20、i-4bb7 U743575 257 Page 3 EN 62063-61:1998 ELECTRICITY METERING EQUIPMENT (AC) - PARTICULAR REQUIREMENTS - Part 61 : Power consumption and voltage requirements 1 Scope This International Standard applies only to newly manufactured “combined meters“, measuring more than one type of electric energy (e

21、.g. active and reactive) and meters integrating additional functions which are not in the scope of the IEC 60687, IEC 61036, IEC 61268 standards and the standard in preparation for static apparent energy meters; these additional functions, all related to electric energy metering are, for instance, m

22、aximum demand indicator, time switches, ripple control or radio receivers, etc. When other devices and functions not related to electric energy metering and billing are enclosed in the same meter case (such as power line carrier devices, load curve recording devices, telephone and radio transceiver

23、or network current and voltage measurement and analysis devices, etc.) this standard applies only to the energy metering and processing section. For all the meter characteristics and functions already described in existing standards, these standards will apply for the corresponding Characteristics a

24、nd functions. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IEC 62053. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and partie

25、s to agreements based on this part of IEC 62053 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC 6068711 992, Alternating current st

26、atic watt-hour meters for active energy (classes 02 S and 0,5 S) IEC 61 036:1996, Alternating current static watt-hour meters for active energy (classes 7 and 2) IEC 61 268:1995, Alternating current static var-hour meters for reactive energy (classes 2 and 3) 3 Definitions For the purpose of this In

27、ternational Standard, the following definitions apply. 3.1 multi-energy meter meter which, in a single case, measures two or three types of energies (watt-hour, var-hour, VA-hou r) Page 4 EN 62053-61:1998 Meter type Multi-energy meter 3.2 multi-function meter basic or multi-energy meter which, in a

28、single case, has functions that are not described in the basic standards for watt-hour, var-hour and VA-hour meters NOTE - Multi-function meters may include: maximum demand indicator, time switches, ripple control or radio receivers, pulse output devices, etc. Single phase Two-phase Three-phase 3w 2

29、,5 W 2w 15 VA 12.5 VA 10 VA per phase ) per phase ) 4 Requirements Communication devices (e.g. telephone- and radio transceivers, PLC, etc.). Functions not related to energy metering and billing i (load curve devices, voltage and current measurement, network analysis, harmonic analysis, etc.) Not pa

30、rt of this standard For polyphase meters the burden is supposed to be evenly shared between the two or three phases supplied. Should a phase voltage be missing it is admitted that the maximum consumption per phase is higher than specified. However the meter shall continue to operate correctly. 4.1 S

31、tandard electrical values Refer to IEC 61036. 4.2 Name-plates Refer to IEC 61036, with the following additions: b) designation of type (see definition 3.1.4 in IEC 61036); each type of measurement performed (watt-hour, var-hour and VA-hour) shall be indicated; I) the class index of each type of meas

32、urement (watt-hour, var-hour and VA-hour). 4.3 Power consumption 4.3.1 Voltage circuits The active and apparent power consumption in each voltage circuit of a meter at reference voltage, reference temperature and reference frequency (see 5.1 .l) shall not exceed the values shown in table 1. Table 1

33、- Power consumption in voltage circuits per phase including the power supply I Multi-function meter 5w 3,5 w I 25VA I 17.5VA 1 15VA In order to match voltage transformers to meters the manufacturer shall state if the burden is inductive or capacitive. STD.BSI BS EN bZU51-bl-ENGL 1997 Lb2YbbS 07q3577

34、 T21 Specified operating range Limit range of operation Page 6 EN 62053-611998 From 0,9 to 1,l U, From 0,O to 1,15 U, The figures in table 1 are mean values. Switching power supplies with peak power values in excess of these specified values are permitted, but it should be ensured that the rating of

35、 associated voltage transformers is adequate. If the meter is operated with an auxiliary power supply, table 1 is not applicable and the maximum consumption of this power supply can be agreed upon between the user and the manufacturer. The consumption of each voltage circuit shall be less than 2 W a

36、nd 10 VA. 4.3.2 Current circuits For multi-energy meters the consumption shall be not greater than the values specified in the appropriate standards. 4.4 Voltage range Table 2 - Voltage range I NOTE - The polyphase meters should also operate within these ranges for I one Dhase onlv. 5 Tests and test

37、 conditions 5.1 General testing procedures 5.1 .l Test conditions All tests shall be carried out under reference conditions according to IEC 61036. NOTE - To simplify the tests, the test conditions will be according to IEC 61036. 5.1.2 Type test The type test defined in IEC 61036 shall be made on on

38、e or more specimens of the meter selected by the manufacturer, to establish its specific characteristics and to prove its conformity with the requirements of this standard. 5.2 Test of power consumption The power consumption in the voltage and current circuit shall be determined at reference values

39、of the influence quantities given in IEC 61036. The overall precision shall be better than 5 0%. 5.2.1 For requirements, see 4.3.1. Test of power consumption of voltage circuits 5.2.2 For requirements, see 4.3.2. Test of power consumption of current circuits STD-BSI i3S EN b2053-bl-ENGL 1799 lb24bb

40、07q3578 bd m Page 6 EN 62053-61:1998 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at t

41、he appropriate places in the text and the pubkations are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the

42、publication referred to applies (including amendments). NOTE: When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication - Year IEC 60687 1992 IEC 61036 1996 IEC 61268 1995 - Title - Year EN/HD Alternating current static w

43、att-hour meters EN 60687 1992 for active energy (classes 0,2 S and 0,5 SI 1993 Alternating current static watt-hour meters EN 61 036 1996 for active energy (classes 1 and 21 Alternating current static var-hour meters EN 61268 1996 for reactive energy (classes 2 and 3) + corr. March BS EN 62053-61:19

44、99 IEC 62053-61 :1998 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent nationai body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Rev

45、isions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be gratfui if anyone finding an inaccuracy or am

46、biguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 0181 996 9000. Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribe

47、rs automatically receive the latest editions of standards. Buying standards Orders for ail BSI, international and foreign standards publications should be addressed to Customer Services. Tel 0181 996 7000. Fax: O181 996 7001. In response to orders for international standards, it is BSI policy to sup

48、ply the BSI implementaion of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various B

49、SI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel 0181 996 7111. Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For detajls of these and other benefits contact Membership Administxation. Tel 0181 996 7002. Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publication