EN 61784-5-3-2013 en Industrial communication networks - Profiles - Part 5-3 Installation of fieldbuses - Installation profiles for CPF 3.pdf

《EN 61784-5-3-2013 en Industrial communication networks - Profiles - Part 5-3 Installation of fieldbuses - Installation profiles for CPF 3.pdf》由会员分享，可在线阅读，更多相关《EN 61784-5-3-2013 en Industrial communication networks - Profiles - Part 5-3 Installation of fieldbuses - Installation profiles for CPF 3.pdf（112页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationIndustrial communication networks ProfilesPart 5-3: Installation of fieldbuses Installation profiles for CPF 3BS EN 61784-5-3:2013National forewordThis British Standard is the UK implementation of EN 61784-5-3:2013. It is identical to IEC 61784-5-3:2013. It supersedes BS EN

2、61784-5-3:2012 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AMT/7, Industrial communications: process measurement andcontrol, including fieldbus.A list of organizations represented on this committee can be obtained onrequest to its secretary.This pub

3、lication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 84195 8ICS 25.040.40; 35.100.40Compliance with a British Standard cannot con

4、fer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61784-5-3:2013EUROPEAN STANDARD EN 61784-5-3 NORME EUROPEN

5、NE EUROPISCHE NORM December 2013 CENELEC European Committee for Electrotechnical StandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation

6、 in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61784-5-3:2013 E ICS 25.040.40; 35.100.40 Supersedes EN 61784-5-3:2012 English version Industrial communication networks - Profiles - Part 5-3: Installation of fieldbuses - Installation profiles for CPF 3 (IEC 61784-5-

7、3:2013) Rseaux de communication industriels - Profils - Partie 5-3: Installation des bus de terrain -Profils dinstallation pour CPF 3(CEI 61784-5-3:2013) Industrielle Kommunikationsnetze - Profile - Teil 5-3: Feldbusinstallation - Installationsprofile fr dieKommunikationsprofilfamilie 3(IEC 61784-5-

8、3:2013) This European Standard was approved by CENELEC on 2013-10-18. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standardthe status of a national standard without any alteration. Up-to-date lists and bibliograp

9、hical references concerning such national standards may be obtained onapplication to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the responsibi

10、lity of a CENELEC member into its own language and notifiedto the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,the Czech Republic, Denmark, Estonia, Finland, For

11、mer Yugoslav Republic of Macedonia, France, Germany,Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61784-5-3:2013Foreword The text

12、of document 65C/738/FDIS, future edition 3 of IEC 61784-5-3, prepared by SC 65C “Industrial networks“ of IEC/TC 65 “Industrial-process measurement, control and automation“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61784-5-3:2013. The following dates are fixed: late

13、st date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-07-18 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-10-18 This document supersedes EN 61784-

14、5-3:2012. EN 61784-5-3:2013 includes the following significant technical changes with respect to EN 61784-5-3:2012: an addition of 4-pair cabling (see C.4.4.1.2.1 and C.5.3.2); an addition of the connector M12 X-Coding (see C.4.4.2.2); an addition of the definition of end-to-end links (see C.4.4.3.1

15、); a revision of Table C.17 (see C.5.2.1) and a formula for the NEXT limits of end-to-end links (see C.6.3.2.1.2). This standard is to be used in conjunction with EN 61918:2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENE

16、LEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61784-5-3:2013 was approved by CENELEC as a European Standard without any modification. BS EN 61784-5-3:2013 EN 61784-5-3:2013Annex ZA (normative)

17、 Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated re

18、ferences, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Annex ZA of EN 61918:2013 applies, except as follows: Publication Year Title E

19、N/HD Year Addition to Annex ZA of EN 61918:2013: IEC 61918 2013 Industrial communication networks - Installation of communication networks in industrial premises EN 61918 2013 BS EN 61784-5-3:2013 EN 61784-5-3:2013 2 61784-5-3 IEC:2013 CONTENTS INTRODUCTION . 9 1 Scope . 10 2 Normative references .

20、10 3 Terms, definitions and abbreviated terms . 10 4 CPF 3: Overview of installation profiles 10 5 Installation profile conventions . 11 6 Conformance to installation profiles 11 Annex A (normative) CP 3/1 (PROFIBUS) specific installation profile . 13 A.1 Installation profile scope . 13 A.2 Normativ

21、e references . 13 A.3 Installation profile terms, definitions, and abbreviated terms . 13 A.3.1 Terms and definitions 13 A.3.2 Abbreviated terms . 14 A.3.3 Conventions for installation profiles . 14 A.4 Installation planning . 14 A.4.1 General . 14 A.4.2 Planning requirements . 14 A.4.3 Network capa

22、bilities 16 A.4.4 Selection and use of cabling components 18 A.4.5 Cabling planning documentation 28 A.4.6 Verification of cabling planning specification . 28 A.5 Installation implementation . 28 A.5.1 General requirements 28 A.5.2 Cable installation . 28 A.5.3 Connector installation 30 A.5.4 Termin

23、ator installation . 33 A.5.5 Device installation . 34 A.5.6 Coding and labeling . 34 A.5.7 Earthing and bonding of equipment and device and shielded cabling . 34 A.5.8 As-implemented cabling documentation . 35 A.6 Installation verification and installation acceptance test 35 A.6.1 General . 35 A.6.2

24、 Installation verification . 35 A.6.3 Installation acceptance test . 37 A.7 Installation administration . 43 A.8 Installation maintenance and installation troubleshooting . 43 Annex B (normative) CP 3/2 (PROFIBUS) specific installation profile 44 B.1 Installation profile scope . 44 B.2 Normative ref

25、erences . 44 B.3 Installation profile terms, definitions, and abbreviated terms . 44 B.3.1 Terms and definitions 44 B.3.2 Abbreviated terms . 45 B.3.3 Conventions for installation profiles . 45 B.4 Installation planning . 46 BS EN 61784-5-3:2013 EN 61784-5-3:201361784-5-3 IEC:2013 3 B.4.1 General .

26、46 B.4.2 Planning requirements . 47 B.4.3 Network capabilities 54 B.4.4 Selection and use of cabling components 59 B.4.5 Cabling planning documentation 74 B.4.6 Verification of cabling planning specification . 74 B.5 Installation implementation . 75 B.5.1 General requirements 75 B.5.2 Cable installa

27、tion . 75 B.5.3 Connector installation 75 B.5.4 Terminator installation . 77 B.5.5 Device installation . 77 B.5.6 Coding and labelling 77 B.5.7 Earthing and bonding of equipment and device and shielded cabling . 77 B.5.8 As-implemented cabling documentation . 77 B.6 Installation verification and ins

28、tallation acceptance test 77 B.6.1 General . 77 B.6.2 Installation verification . 77 B.6.3 Installation acceptance test . 78 B.7 Installation administration . 78 B.8 Installation maintenance and installation troubleshooting . 78 Annex C (normative) CP 3/3, CP 3/4, CP 3/5, CP 3/6 (PROFINET) specific

29、installation profile . 79 C.1 Installation profile scope . 79 C.2 Normative references . 79 C.3 Installation profile terms, definitions, and abbreviated terms . 79 C.3.1 Terms and definitions 79 C.3.2 Abbreviated terms . 79 C.3.3 Conventions for installation profiles . 80 C.4 Installation planning .

30、 80 C.4.1 General . 80 C.4.2 Planing requirements 80 C.4.3 Network capabilities 80 C.4.4 Selection and use of cabling components 83 C.4.5 Cabling planning documentation 98 C.4.6 Verification of cabling planning specification . 99 C.5 Installation implementation . 99 C.5.1 General requirements 99 C.5

31、.2 Cable installation . 99 C.5.3 Connector installation 100 C.5.4 Terminator installation . 102 C.5.5 Device installation . 102 C.5.6 Coding and labeling . 102 C.5.7 Earthing and bonding of equipment and device and shielded cabling . 102 C.5.8 As-implemented cabling documentation . 103 C.6 Installat

32、ion verification and installation acceptance test 103 C.6.1 General . 103 C.6.2 Installation verification . 103 C.6.3 Installation acceptance test . 105 BS EN 61784-5-3:2013 EN 61784-5-3:2013 4 61784-5-3 IEC:2013 C.7 Installation administration . 106 C.8 Installation maintenance and installation tro

33、ubleshooting . 107 Bibliography 108 Figure 1 Standards relationships 9 Figure A.1 Recommended combination of shielding and earthing for CP 3/1 networks with RS 485-IS . 26 Figure A.2 Sub-D connector pin numberings (front view) 31 Figure A.3 5-pin M12 female socket . 32 Figure A.4 5-pin M12 male plug

34、 for CP 3/1 . 32 Figure A.5 Test circuit A Resistance measurement of data line B and shield . 38 Figure A.6 Test circuit B Resistance measurement of data line A and shield 38 Figure A.7 Test circuit C Resistance measurement of data line A, data line B, and shield 39 Figure A.8 Test circuit D Resista

35、nce measurement between data line A and B 39 Figure A.9 Resistance measurement without 9-pin Sub-D plug 39 Figure A.10 Loop core resistance (cable type A) 40 Figure A.11 Action and resolution tree for measurement 1 (RS 485 and RS 485-IS) 41 Figure A.12 Action and resolution tree for measurement 2 (R

36、S 485 and RS 485-IS) 42 Figure A.13 Action and resolution tree for measurement 3 (RS 485 and RS 485-IS) 42 Figure B.1 Connection of CP 3/1 networks . 47 Figure B.2 Typical fieldbus architecture . 49 Figure B.3 Fieldbus with stations supplied by auxiliary power sources . 50 Figure B.4 Fieldbus model

37、. 52 Figure B.5 Current modulation (Manchester II code) 53 Figure B.6 Tree topology . 54 Figure B.7 Bus topology . 55 Figure B.8 Combination of the tree topology and the bus topology . 55 Figure B.9 Fieldbus extension 56 Figure B.10 Recommended combination of shielding and earthing . 69 Figure B.11

38、Ideal combination of shielding and earthing 70 Figure B.12 Capacitive earthing . 71 Figure B.13 Galvanic isolated field device 73 Figure B.14 Pin assignment of the male and female connectors IEC 60947-5-2 (A-coding) . 76 Figure C.1 Definition of end-to-end-link 93 Figure C.2 End-to-end link without

39、interconnections . 94 Figure C.3 Assembled end-to-end link . 94 Figure C.4 Connectionless optical fibre link . 95 Figure C.5 Assembled optical fibre link 95 Figure C.6 Shielded connectors for CP 3/3, CP 3/4, CP 3/5 and CP 3/6 fieldbus networks . 101 Figure C.7 Pin-assignment for a straight cable . 1

40、01 Table A.1 Excerpt of MICE definition 16 BS EN 61784-5-3:2013 EN 61784-5-3:201361784-5-3 IEC:2013 5 Table A.2 Basic network characteristics for balanced cabling not based on Ethernet (ISO/IEC 8802-3) 17 Table A.3 Network characteristics for optical fibre cabling 18 Table A.4 Information relevant t

41、o copper cable: fixed cables 19 Table A.5 Information relevant to optical fibre cables . 20 Table A.6 Connectors for copper cabling CPs not based on Ethernet . 21 Table A.7 Optical fibre connecting hardware 21 Table A.8 Relationship between FOC and fibre types (CP 3/1) . 21 Table A.9 Parameters for

42、balanced cables . 28 Table A.10 Parameters for silica optical fibre cables 29 Table A.11 Parameters for POF optical fibre cables . 29 Table A.12 Parameters for hard clad silica optical fibre cables . 29 Table A.13 Use of 9 pin Sub-D connector pins (RS 485) 31 Table A.14 Use of 9 pin Sub-D connector

43、pins (RS 485-IS) 31 Table A.15 Use of M12 connector pins (RS 485) 33 Table A.16 Use of M12 connector pins (RS 485-IS) . 33 Table A.17 Maximum fibre channel attenuation for CP 3/1 (PROFIBUS) 43 Table B.1 Valid parameter range of the FISCO model for use as EEx ib IIC / IIB 51 Table B.2 Valid parameter

44、 range of the FISCO model for use as EEx ia IIC . 51 Table B.3 Power supply (operational values) . 57 Table B.4 Line lengths which can be achieved . 57 Table B.5 Limit values for distortion, reflection and signal delay. 58 Table B.6 Recommended maximum cable lengths including spurs . 58 Table B.7 Re

45、commended length of the spurs . 59 Table B.8 Maximum length of the splices . 59 Table B.9 Information relevant to copper cable: fixed cables 60 Table B.10 Safety limit values for the fieldbus cable 61 Table B.11 Connectors for copper cabling CPs not based on Ethernet . 62 Table B.12 Mixing devices f

46、rom different categories 64 Table B.13 Electrical characteristics of fieldbus interfaces . 65 Table B.14 Recommended data sheet specifications for CP 3/2 devices 66 Table B.15 Parameters for balanced cables . 75 Table B.16 Contact assignments for the external connector for harsh industrial environme

47、nts 76 Table C.1 General transmission media selection information . 81 Table C.2 Network characteristics for balanced cabling based on Ethernet (ISO/IEC 8802-3) 82 Table C.3 Network characteristics for optical fibre cabling . 82 Table C.4 Information relevant to copper cable: CP 3/3, CP 3/4, CP 3/5

48、and CP 3/6 type A fixed cables . 83 Table C.5 Information relevant to copper cable: CP 3/3, CP 3/4, CP 3/5 and CP 3/6 type B flexible cables 84 Table C.6 Information relevant to copper cable: CP 3/3, CP 3/4, CP 3/5 and CP 3/6 type C special cables 85 Table C.7 Information relevant to copper cable: C

49、P 3/3, CP 3/4, CP 3/5 and CP 3/6 of cabinet cord sets 85 BS EN 61784-5-3:2013 EN 61784-5-3:2013 6 61784-5-3 IEC:2013 Table C.8 Information relevant to optical fibre cables . 86 Table C.9 Requirements for plastic and hard clad silica optical fibre cables . 87 Table C.10 Requirements for glass multimode optical fibre cables . 88 Table C.11 Requirements for glass sin