EN 61754-16-2000 en Fibre Optic Connector Interfaces Part 16 Type PN Connector Family《光纤连接器接口 第16部分 PN型连接器系列 IEC 61754-16 1999》.pdf

《EN 61754-16-2000 en Fibre Optic Connector Interfaces Part 16 Type PN Connector Family《光纤连接器接口 第16部分 PN型连接器系列 IEC 61754-16 1999》.pdf》由会员分享，可在线阅读，更多相关《EN 61754-16-2000 en Fibre Optic Connector Interfaces Part 16 Type PN Connector Family《光纤连接器接口 第16部分 PN型连接器系列 IEC 61754-16 1999》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 STD*BSI BS EN b375V-lb-ENGL 2000 W LbZibbS 0853958 77b BRITISH STANDARD Fibre optic connector interfaces - Part 16: vpe PN connector family The European Stanur British Standaxd ICs 33.180.20 El 61754-162000 has the status of a BS EN 61754-16:ZO IEC 61 754-16: 1999 NO COPYDUG WITHOUT BSI PERMISSION

2、EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 61764162000 direction of the Electrotechnicai Sector Conunittee, was put %bed under the authority of the Standards Committee and comes into effect on 15 June 2000 hd. No. National foreword D - monitor related international and European developments and prom

3、ulgate them in the UK. A list of organizaons represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, ail IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during t

4、he change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their correspond

5、ing European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalog

6、ue. A British Standard does not purport to include all the necessary provisions of a contsact. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document compri

7、ses a bnt cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. O BSI 06-2000 I I ISBN O 680 34963 2 STD-BSI BS EN bL754-Lb-ENGL 2000 W Lb2ibbS 085L9bO 32

8、4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCH E NORM EN 61754-16 March 2000 ICs 33.180.20 English version Fibre optic connector interfaces Part 16: Type PN connector family (IEC 61 754-1 6: 1999) Interfaces de connecteurs pour fibres optiques Partie 16: Famille de connecteurs de Steckgesichter von L

9、ic htw el lenleite r- Stec kve r bi nd ern Teil 16: Bauart PN Steckverbinderfamilie type PN (CE1 61 754-1 611 999) (IEC 61 754-1 6:1999) This European Standard was approved by CENELEC on 2000-01-01. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the cond

10、itions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in t

11、hree official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechn

12、ical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalis

13、ation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassari 35, B - 1050 Brussels 2000 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61754-16:ZOOo E Page 2 EN 61754-16:2000 Forewo

14、rd The text of document 86B/l245/FDlS, future edition 1 of IEC 61 754-1 6, prepared by SC 866, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61 754-1 6 on 2000-0 1 -0 1 . The fo

15、llowing dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement with the EN have to be withdrawn - latest date by which the national standards conflicting (dop) 2000- 1 0-0 1 (daw) 2003-0 1 -0 1 Endors

16、ement notice The text of the International Standard IEC 61 754-1 6:1999 was approved by CENELEC as a European Standard without any modification. STD-BSI BS EN bL759-Lb-ENGL 2000 I Lb29bbS O5L7b2 LT7 Page 3 EN 61754-16:ZOOO CONTENTS Page Clause 1 Scope 4 3 Interfaces 4 2 Description 4 O BSI 06-2000 P

17、age 4 EN 61754-16:ZOOO FIBRE OPTIC CONNECTOR INTERFACES - Part 16: Type PN connector family 1 Scope This part of IEC 61754 defines the standard interface dimensions for type PN family of connectors. 2 Description The parent connector for type PN connector family is a duplex plug connector which is c

18、haracterized by a 10,16 mm pitch, and a 2,5 mm nominal ferrule diameter. It includes two types of plugs, PN-I and PN-II. PN-I is a high precison type which has floating ferrules with springs. PN-II is a low-cost type, variant of PN-I, which has fixed ferrules, no springs, incorporating a one piece b

19、ody. Both plugs are mechanically compatible with both the adaptor or the socket. 3 Interfaces This standard contains the following standard interfaces: - interface 16-1: (duplex) plug PN-I connector interface - interface 16-2: (duplex) plug PN-II connector interface - interface 16-3: (duplex) adapto

20、r connector interface - interface 16-4: (duplex) socket (receptacle) connector interface 8 BSI 06-2000 Page 6 EN 61754-16:2000 Optical datum target C I F 4 I *-I- U l IEC 1494199 Figure 1 - Plug PN-I connector interface O BSI 06-2000 STD-BSI BS EN bL75V-Lb-ENGL 2000 II lib2Vbb9 08519b5 7Ob Page 6 EN

21、 61754-16:ZOOO Table 1 - Dimensions of the plug PN-I connector interface Reference A B C E F G H I J K L M N S U V CA CB Minimum Dimensions mm Maximum 2,49 4,3 53 1,49 17,45 15,95 10,12 3,8 5,30 - 6,8 23 6,55 3,6 14,4 4,4 1,35 0,8 2,50 4,s 6,O 1,595 17,65 16,09 10,20 4,299 5,40 2,s - 3,15 6,9 4,5 14

22、,8 4,6 1,7 1,15 Notes 4 3 2 1 Chamfer Chamfer NOTE 1 - Dimension S is movable to 3,O mm when inserted into the adaptor or socket and locked to dimension K (see figures 3 and 4). NOTE 2 - Dimension L is given for plug endface when not mated. It is movable by a certain axial compression force. When ma

23、ted with the adaptor or socket, dimension L is 6,l mm to 6,451 mm. And then ferrule compression force shall be 4,3 N to 8,l N. NOTE 3 - Dimension K is given for mating with the adaptor dimension K (see figure 3) or the socket dimension K (see figure 4). NOTE 4 - Dimension H is specified when mated w

24、ith the adaptor or socket. NOTE 5 - Plane 21 is the mechanical reference plane; it corresponds to the adaptor plane Z1 in figure 3 or the socket plane 21 in figure 4. When mated with the socket, plane Y1 mates with the socket plane Y (see figure 4). When mated with the adaptor, plane X corresponds t

25、o the adaptor plane X in figure 3. O BSI 06-2000 STD-BSI BS EN bL759-Lb-ENGL 2000 M Lb29bbS 085LSbb 842 W Page 7 EN 61764-16:ZOOO NB NA W F G 1 Optical datum targel ._. T 1 IEC 149.599 Figure 2 - Plug PN-II connector interface O BSI 06-2000 Page 8 EN 61754-16:2000 Table 2 - Dimensions of the plug PN

26、-II connector interface Reference A B C E F G H I J K KY N NA NB P PX R S T U v CA CB Minimum Dimensions mm Maximum 2,42 4,3 5,8 1,49 17,45 15,95 10,12 3-8 5,30 - 0,7 6,55 2,7 3,85 1,75 0,9 2,7 3.6 6,35 14,4 4.4 1,35 03 2,50 4,5 6,O 1,595 17.65 16.09 10,20 4,299 5,40 2,5 0,799 6,9 2.9 4,o 1,91 1 ,o

27、2,9 43 6,45 14,8 4,6 1.7 1,15 Notes 4 4 2 5 5 5 3 3 1 3 Chamfer Chamfer JOTE 1 - Dimension S is movable to 3,O mm when inserted into an adaptor or socket, and locked to dimension (see figures 3 and 4). JOTE 2 - Dimension K is given for mating with the adaptor or socket (see figures 3 and 4) dimensio

28、n K. JOTE 3 - Detents of dimension T are deflected when inserted into the adaptor or socket (see figures 3 and 4), ind mated with rectangle holes of dimension P-R. JOTE 4 - Plane Y2 mates with socket (see figure 4) plane Y. Plane 22 corresponds to the adaptor or socket see figures 3 and 4) plane 22.

29、 JOTE 5 - Dimension N = dimension NA + dimension NB. O BSI 06-2000 STD=BSI BS EN bL759-Lb-ENGL 2000 W Lb2Libb7 08517b bL5 m Page 9 EN 61764-16:2000 1- jp Cross-section B-B 1 B 1 I IEC 1496/99 Figure 3 - Adaptor connector interface O BSI 06-2000 Page 10 EN 61754-16:2000 Table 3 - Dimensions of the ad

30、aptor connector interface Rfrence A B C D E F G H I J K L LB M MB N O P Q R CA Dimensions mm Minimum 2,501 3,9 6,l 6,05 1,6 18,2 16,l 10,12 4,5 5,05 2,6 6,25 6,65 2,55 2.25 6,95 1,3 1,3 3.5 3,5 1 ,o Maximum 2,521 4,1 6,25 6,25 1,7 18,5 16,2 10,20 4,7 5,15 2,8 6.45 6,75 2,8 23 - 13 1,s 3,7 3,7 1,3 No

31、tes 2 3 1 1 Chamfer NOTE 1 - This hole is given for mating with PN-II plug; it is not used for mating with PN-I plug. NOTE 2 - Dimension C is specified on line 6-B, and shall be capable of accepting plug PN-Ils dimension T (see figure 2). When PN-II plug is mated, detents of PN-II are also inserted

32、with deflection of dimension C. NOTE 3 - X (dimension Ls left plane) shows plug ferrule endface in mated condition; it corresponds to plug plane X (see figures 1 and 2). When mated with PN-I plug, plane Z1 corresponds to plug plane 21 (see figure I). When mated with PN-II plug, plane 22 corresponds

33、to plug plane 22 (see figure 2). Q BSI 06-2000 7 Y Cross-section A-A B- Page 11 EN 61754-16:2000 i 1 I 1 Cross-section B-B Figure 4 - Socket (receptacle) connector interface IEC 1497/99 O BSI 06-2000 STDIBSI BS EN bl754-lb-ENGL 2000 lb24bb9 0853971 LOT W Page 12 EN 61764-16:2000 Table 4 - Dimensions

34、 of the socket (receptacle) connector interface Rfrence A B C D E F G H I J K KY M MB N O P PY Q R CA Minimum Dimensions mm Maximum 2,501 3,9 6-1 6,05 1,6 18,2 16,l 10,12 4-5 5,3 2,6 0,s 2,75 24 6,95 1,3 1.3 1,15 3,5 33 1 ,o 2,551 43 6,25 6,25 1,7 18,5 16,2 10,20 4,7 5-4 2,8 0,9 2.85 23 7,25 IS 13 1

35、,25 3,7 3,7 12 Notes 2 4 5 5 5 1 5 1 Chanfrein NOTE 1 - This hole is used for mating with PN-II plug; it is not used when mating with PN-I plug. NOTE 2 - Dimension C is specified on line B-B, and shall be capable of accepting plug PN-Ils dimension T see figure 2). When PN-II plug is mated, detents o

36、f PN-II are also inserted with deflection of dimension C. NOTE 3 - When mated with PN-I plug, plane Y corresponds to plug plane YI, and plane 21 corresponds to plug dane 21. When mated with PN-II plug, plane Y corresponds to plug plane Y2, and plane 22 corresponds to plug Diane 22. VOTE 4 - X (dimen

37、sion Js left plane) shows plug ferrule endface at mating. VOTE 5 - Dimension KY + dimension M = dimension PY + dimension MB (minimum: 3,55; maximum: 3.75). O BSI 06-2000 STD=BSI BS EN b175Y-Lb-ENGL 2000 Lb24bb9 0851972 04b = BS EN 61754162000 IEC 61754-16: 1999 BSI 389 Chiswick High Road London w4 4

38、AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the intemational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision

39、. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the ty of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secret

40、ary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel O20 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying

41、 standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as B

42、ritish Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give

43、 details on all its products and services. Contact the Information Centre. Tel 020 8996 71 11. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits

44、contact Membership Administsati on Tel O20 8996 7002. Fax: 020 8996 7001. Copyright Copynght subsists in ail BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 19

45、88 no extract may be reproduced, stored in a retrieval system or tsansmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the come of implementing the standard, of necessary details

46、 such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 020 8996 7070.