EN 61215-1-2-2017 en Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2 Special requirements for testing of thinfilm Cadmium Telluride (CdTe).pdf

《EN 61215-1-2-2017 en Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2 Special requirements for testing of thinfilm Cadmium Telluride (CdTe).pdf》由会员分享，可在线阅读，更多相关《EN 61215-1-2-2017 en Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2 Special requirements for testing of thinfilm Cadmium Telluride (CdTe).pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Terrestrial photovoltaic (PV) modules Design qualification and type approvalPart 1-2: Special requirements for testing of thin-film Cadmium Telluride (CdTe) based photovoltaic (PV) modulesBS EN 61215-1-2:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN ST

2、ANDARD NORME EUROPENNE EUROPISCHE NORM EN 61215-1-2 April 2017 ICS 27.160 Supersedes EN 61646:2008 English Version Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2: Special requirements for testing of thin-film Cadmium Telluride (CdTe) based photovoltaic (PV)

3、 modules (IEC 61215-1-2:2016) Modules photovoltaques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 1-2: Exigences particulires dessai des modules photovoltaques (PV) au tellurure de cadmium (CdTe) couches minces (IEC 61215-1-2:2016) Terrestrische kristal

4、line Silizium-Photovoltaik-(PV)-Module - Bauarteignung und Bauartzulassung - Teil 1-2: Besondere Anforderungen fr Prfungen von Cadmiumtellurid-(CdTe)-Photovoltaik-(PV)-Modulen (IEC 61215-1-2:2016) This European Standard was approved by CENELEC on 2017-01-11. CENELEC members are bound to comply with

5、the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Managem

6、ent Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the sa

7、me status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Li

8、thuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektr

9、otechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61215-1-2:2017 E National forewordThis British Standard is the UK implementation of EN 61215-1

10、-2:2017. It is identical to IEC 61215-1-2:2016. Together with BS EN 61215-1-3:2017 and BS EN 61215-1-4:2017, it supersedes BS EN 61646:2008 , which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GEL/82, Photovoltaic Energy Systems.A list of organizations re

11、presented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0

12、 580 87367 6ICS 27.160Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STA

13、NDARDBS EN 61215-1-2:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61215-1-2 April 2017 ICS 27.160 Supersedes EN 61646:2008 English Version Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1-2: Special requirements for testing of thin-film Cadmium Tell

14、uride (CdTe) based photovoltaic (PV) modules (IEC 61215-1-2:2016) Modules photovoltaques (PV) pour applications terrestres - Qualification de la conception et homologation - Partie 1-2: Exigences particulires dessai des modules photovoltaques (PV) au tellurure de cadmium (CdTe) couches minces (IEC 6

15、1215-1-2:2016) Terrestrische kristalline Silizium-Photovoltaik-(PV)-Module - Bauarteignung und Bauartzulassung - Teil 1-2: Besondere Anforderungen fr Prfungen von Cadmiumtellurid-(CdTe)-Photovoltaik-(PV)-Modulen (IEC 61215-1-2:2016) This European Standard was approved by CENELEC on 2017-01-11. CENEL

16、EC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on ap

17、plication to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-

18、CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary,

19、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotec

20、hnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61215-1-2:2017 E BS EN 61215-1-2:2017EN 61215-1-2:2017 2 E

21、uropean foreword The text of document 82/1182/FDIS, future edition 1 of IEC 61215-1-2, prepared by IEC/TC 82 “Solar photovoltaic energy systems“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61215-1-2:2017. The following dates are fixed: latest date by which the docume

22、nt has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-10-28 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-04-28 This document supersedes EN 61646:2008. Attention is drawn to

23、 the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61215-1-2:2016 was approved by CENELEC as a E

24、uropean Standard without any modification. BS EN 61215-1-2:2017EN 61215-1-2:2017 2 European foreword The text of document 82/1182/FDIS, future edition 1 of IEC 61215-1-2, prepared by IEC/TC 82 “Solar photovoltaic energy systems“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC

25、as EN 61215-1-2:2017. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2017-10-28 latest date by which the national standards conflicting with the document have to be with

26、drawn (dow) 2020-04-28 This document supersedes EN 61646:2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The

27、text of the International Standard IEC 61215-1-2:2016 was approved by CENELEC as a European Standard without any modification. EN 61215-1-2:2017 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications Annexes ZA of EN 61215-1:2016 and

28、EN 61215-2:2017 are applicable. BS EN 61215-1-2:2017This page deliberately left blank 2 IEC 61215-1-2:2016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope and object . 5 2 Normative references 5 3 Terms and definitions 5 4 Test samples . 5 5 Marking and documentation . 5 6 Testing 5 7 Pass criteria 6 8 Major

29、 visual defects . 6 9 Report . 6 10 Modifications . 6 11 Test flow and procedures 6 11.1 Visual inspection (MQT 01) . 6 11.2 Maximum power determination (MQT 02) 6 11.3 Insulation test (MQT 03) . 6 11.4 Measurement of temperature coefficients (MQT 04) 6 11.5 Measurement of nominal module operating t

30、emperature (NMOT) (MQT 05) 6 11.6 Performance at STC (MQT 06.1) and NMOT (MQT 06.2) 6 11.7 Performance at low irradiance (MQT 07) . 6 11.8 Outdoor exposure test (MQT 08) . 7 11.9 Hot-spot endurance test (MQT 09) 7 11.9.1 Purpose . 7 11.9.2 Hot-spot effect . 7 11.9.3 Classification of cell interconne

31、ction 7 11.9.4 Apparatus 7 11.9.5 Procedure 7 11.9.6 Final measurements 7 11.9.7 Requirements 7 11.10 UV preconditioning test (MQT 10) . 7 11.11 Thermal cycling test (MQT 11) 7 11.12 Humidity-freeze test (MQT 12) 7 11.13 Damp heat test (MQT 13) 8 11.14 Robustness of terminations test (MQT 14) 8 11.1

32、5 Wet leakage current test (MQT 15) . 8 11.16 Static mechanical load test (MQT 16) 8 11.17 Hail test (MQT 17) 8 11.18 Bypass diode testing (MQT 18) . 8 11.19 Stabilization (MQT 19) 8 11.19.2 Criterion definition for stabilization . 8 11.19.3 Light induced stabilization procedure . 8 11.19.4 Other st

33、abilization procedures . 8 11.19.5 Initial stabilization (MQT 19.1) . 8 11.19.6 Final stabilization (MQT 19.2) 9 2 IEC 61215-1-2:2016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope and object . 5 2 Normative references 5 3 Terms and definitions 5 4 Test samples . 5 5 Marking and documentation . 5 6 Testing

34、5 7 Pass criteria 6 8 Major visual defects . 6 9 Report . 6 10 Modifications . 6 11 Test flow and procedures 6 11.1 Visual inspection (MQT 01) . 6 11.2 Maximum power determination (MQT 02) 6 11.3 Insulation test (MQT 03) . 6 11.4 Measurement of temperature coefficients (MQT 04) 6 11.5 Measurement of

35、 nominal module operating temperature (NMOT) (MQT 05) 6 11.6 Performance at STC (MQT 06.1) and NMOT (MQT 06.2) 6 11.7 Performance at low irradiance (MQT 07) . 6 11.8 Outdoor exposure test (MQT 08) . 7 11.9 Hot-spot endurance test (MQT 09) 7 11.9.1 Purpose . 7 11.9.2 Hot-spot effect . 7 11.9.3 Classi

36、fication of cell interconnection 7 11.9.4 Apparatus 7 11.9.5 Procedure 7 11.9.6 Final measurements 7 11.9.7 Requirements 7 11.10 UV preconditioning test (MQT 10) . 7 11.11 Thermal cycling test (MQT 11) 7 11.12 Humidity-freeze test (MQT 12) 7 11.13 Damp heat test (MQT 13) 8 11.14 Robustness of termin

37、ations test (MQT 14) 8 11.15 Wet leakage current test (MQT 15) . 8 11.16 Static mechanical load test (MQT 16) 8 11.17 Hail test (MQT 17) 8 11.18 Bypass diode testing (MQT 18) . 8 11.19 Stabilization (MQT 19) 8 11.19.2 Criterion definition for stabilization . 8 11.19.3 Light induced stabilization pro

38、cedure . 8 11.19.4 Other stabilization procedures . 8 11.19.5 Initial stabilization (MQT 19.1) . 8 11.19.6 Final stabilization (MQT 19.2) 9 BS EN 61215-1-2:2017IEC 61215-1-2:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ TERRESTRIAL PHOTOVOLTAIC (PV) MODULES DESIGN QUALIFICATION AND TYP

39、E APPROVAL Part 1-2: Special requirements for testing of thin-film Cadmium Telluride (CdTe) based photovoltaic (PV) modules FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC Nationa

40、l Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly

41、 Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-government

42、al organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on tec

43、hnical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by

44、IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unif

45、ormity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5)

46、 IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensu

47、re that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of a

48、ny nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the ref

49、erenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61215-1-2 has been prepared by IEC technical committee 82: Solar photovoltaic energy systems. This edition cancels and replaces the second edition of IEC 61646, issued in 2008, and constit