EN 60745-2-17-2010 en Hand-held motor-operated electric tools - Safety - Part 2-17 Particular requirements for routers and trimmers《手持式电动工具 安全性 第2-17部分 刳刨机和修剪机的特殊要求》.pdf

《EN 60745-2-17-2010 en Hand-held motor-operated electric tools - Safety - Part 2-17 Particular requirements for routers and trimmers《手持式电动工具 安全性 第2-17部分 刳刨机和修剪机的特殊要求》.pdf》由会员分享，可在线阅读，更多相关《EN 60745-2-17-2010 en Hand-held motor-operated electric tools - Safety - Part 2-17 Particular requirements for routers and trimmers《手持式电动工具 安全性 第2-17部分 刳刨机和修剪机的特殊要求》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationHand-held motor-operated electric tools SafetyPart 2-17: Particular requirements for routers and trimmersBS EN 60745-2-17:2010National forewordThis British Standard is the UK imp

2、lementation of EN 60745-2-17:2010. It was derived by CENELEC from IEC 60745-2-17:2010. It supersedes BS EN 60745-2-17:2003, which will be withdrawn on 1 September 2013. The UK participation in its preparation was entrusted to Technical Committee CPL/116, Portable motor-operated tools.A list of organ

3、izations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 60329 7 ICS 25.140.20Compliance with a British Standa

4、rd cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2011.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60745-2-17:2010The CENELEC common modification

5、s have been implemented at the appropriate places in the text. The start and finish of each common modification is indicated in the text by tags .EUROPEAN STANDARD EN 60745-2-17 NORME EUROPENNE EUROPISCHE NORM September 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europ

6、en de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60745-2-17:2010 E ICS 25.140.20 Supe

7、rsedes EN 60745-2-17:2003 + A11:2007English version Hand-held motor-operated electric tools - Safety - Part 2-17: Particular requirements for routers and trimmers (IEC 60745-2-17:2010, modified) Outils lectroportatifs moteur - Scurit - Partie 2-17: Rgles particulires pour les dfonceuses et les affle

8、ureuses (CEI 60745-2-17:2010, modifie) Handgefhrte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-17: Besondere Anforderungen fr Oberfrsen und Kantenfrsen (IEC 60745-2-17:2010, modifiziert) This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply with

9、 the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretaria

10、t or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the of

11、ficial versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Polan

12、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 116/38/FDIS, future edition 3 of IEC 60745-2-17, prepared by TC 116, Safety of hand-held motor-operated electric tools, was submitted to the IEC-CENELEC parallel vote. A draft a

13、mendment, prepared by the Technical Committee CENELEC TC 116, Safety of motor-operated electric tools, was submitted to the formal vote. The combined texts were approved by CENELEC as EN 60745-2-17 on 2010-09-01. This European Standard supersedes EN 60745-2-17:2003 + A11:2007. Attention is drawn to

14、the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implementedat national level by pu

15、blication of an identical national standard or by endorsement (dop) 2011-09-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2013-09-01 This European Standard is divided into two parts: Part 1: General requirements which are common to most hand

16、-held electric motor operated tools (for the purpose of this standard referred to simply as tools) which could come within the scope of this standard; Part 2: Requirements for particular types of tools which either supplement or modify the requirements given in Part 1 to account for the particular h

17、azards and characteristics of these specific tools. This draft European Standard has been prepared under Mandate M/396 given to CENELEC by the European Commission and the European Free Trade Association and covers essential requirements of EC Directive 2006/42/EC. See Annex ZZ. Compliance with the r

18、elevant clauses of Part 1 together with this Part 2 provides one means of conforming with the essential health and safety requirements of the Directive concerned. Warning: Other requirements and other EC Directives can be applicable to the products falling within the scope of this standard. This sta

19、ndard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2. This Part 2-17 is to be used in conjunction with EN 60745-1:2009. When this standard states “addition“, “modification“ or “replacement“, the relevant text in Part 1 is to be adapted accordingly. Subclauses, tables and figur

20、es which are additional to those in Part 1 are numbered starting from 101; additional annexes are lettered AA, BB, etc. Subclauses, tables and figures which are additional to those in IEC 60745-2-17:2010 (116/38/FDIS) are prefixed “Z”. BS EN 60745-2-17:2010EN 60745-2-17:2010 (E) - 2 -Annex ZZ has be

21、en added by CENELEC. NOTE In this standard the following print types are used: - requirements proper: in roman type - test specifications: in italic type;- explanatory matter: in smaller roman type. _ Endorsement notice The text of the International Standard IEC 60745-2-17:2010 was approved by CENEL

22、EC as a European Standard with agreed common modifications as given below. Foreword to amendment A1The text of document 116/38/FDIS, future edition 3 of IEC 60745-2-17, prepared by TC 116, Safety of hand-held motor-operated electric tools, was submitted to the IEC-CENELEC parallel vote. A draft amen

23、dment, prepared by the Technical Committee CENELEC TC 116, Safety of motor-operated electric tools, was submitted to the formal vote. The combined texts were approved by CENELEC as EN 60745-2-17 on 2010-09-01. This European Standard supersedes EN 60745-2-17:2003 + A11:2007. Attention is drawn to the

24、 possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publ

25、ication of an identical national standard or by endorsement (dop) 2011-09-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2013-09-01 This European Standard is divided into two parts: Part 1: General requirements which are common to most hand-h

26、eld electric motor operated tools (for the purpose of this standard referred to simply as tools) which could come within the scope of this standard; Part 2: Requirements for particular types of tools which either supplement or modify the requirements given in Part 1 to account for the particular haz

27、ards and characteristics of these specific tools. BS EN 60745-2-17:2010EN 60745-2-17:2010 (E)- 3 -_This draft European Standard has been prepared under Mandate M/396 given to CENELEC by the European Commission and the European Free Trade Association and covers essential requirements of EC Directive

28、2006/42/EC. See Annex ZZ. Compliance with the relevant clauses of Part 1 together with this Part 2 provides one means of conforming with the essential health and safety requirements of the Directive concerned. Warning: Other requirements and other EC Directives can be applicable to the products fall

29、ing within the scope of this standard. This standard follows the overall requirements of EN ISO 12100-1 and EN ISO 12100-2. This Part 2-17 is to be used in conjunction with EN 60745-1:2009. When this standard states “addition“, “modification“ or “replacement“, the relevant text in Part 1 is to be ad

30、apted accordingly. Subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 101; additional annexes are lettered AA, BB, etc. Subclauses, tables and figures which are additional to those in IEC 60745-2-17:2010 (116/38/FDIS) are prefixed “Z”. Annex ZZ has been

31、 added by CENELEC. NOTE In this standard the following print types are used: - requirements proper: in roman type - test specifications: in italic type;- explanatory matter: in smaller roman type. _ Endorsement notice The text of the International Standard IEC 60745-2-17:2010 was approved by CENELEC

32、 as a European Standard with agreed common modifications as given below. BS EN 60745-2-17:2010EN 60745-2-17:2010 (E) - 4 -CONTENTS 1 Scope.7 2 Normative references .7 3 Terms and definitions .7 4 General requirements.7 5 General conditions for the tests 7 6 Void7 7 Classification8 8 Marking and inst

33、ructions.9 9 Protection against access to live parts9 10 Starting 9 11 Input and current 9 12 Heating 9 13 Leakage current .9 14 Moisture resistance 10 15 Electric strength .10 16 Overload protection of transformers and associated circuits .10 17 Endurance10 18 Abnormal operation 10 19 Mechanical ha

34、zards10 20 Mechanical strength .11 21 Construction.11 22 Internal wiring.11 23 Components .11 24 Supply connection and external flexible cords 11 25 Terminals for external conductors.11 26 Provision for earthing .11 27 Screws and connections.12 28 Creepage distances, clearances and distances through

35、 insulation12 29 Resistance to heat, fire and tracking.12 30 Resistance to rusting12 31 Radiation, toxicity and similar hazards12 Annexes .15 Annex K (normative) Battery tools and battery packs .15 Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sou

36、rces.15 Annex M (normative) Safety of working stands for operation with hand-held motor-operated electric tools 16 Bibliography34 BS EN 60745-2-17:2010EN 60745-2-17:2010 (E)- 5 -Annex ZZ (informative) Coverage of Essential Requirements of Directive 2006/42/EC 33Figure 101 Measurement of distance bet

37、ween handle and cutter . 13 Figure M.301 Working stand with installed hand-held router.26 Figure M.302 Dimensions of table 26 Figure M.303 Dimension of table rings .27 Figure M.304 Fence .27 Figure M.305 Examples of guides suitable for curved work 28 Figure M.306 Test probe29 Figure M.307 Definition

38、 of fence pressure device deflection measuring point and directions of application of test forces .29 Figure M.308 Definition of fence pressure device deflection measuring point and directions of application of test forces (vertical view) 30 Figure M.309 Definition of table pressure device deflectio

39、n measuring point and directions of application of test forces (horizontal view) 30 Figure M.310 Definition of the adjustable guard deflection measuring points and directions of application of test forces .31 Figure M.311 Definition of guiding steady deflection measuring points and directions of app

40、lication of test forces .32 Figure M.312 Definition of the adjustment of the fence plates in the direction perpendicular to the plane of the fence .32 Table M.301 Fences and table pressure device displacement 24 Table M.302 Adjustable guard deflection .24 Table M.303 Guiding steady deflection 25 BS

41、EN 60745-2-17:2010EN 60745-2-17:2010 (E) - 6 -Figure Z101 - Position of transducers 14 Table Z101 Test conditions 8 HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY Part 2-17: Particular requirements for routers and trimmers 1 Scope This clause of Part 1 is applicable, except as follows: Addition: Thi

42、s standard applies to routers and trimmers. 2 Normative references This clause of Part 1 is applicable. 3 Terms and definitions This clause of Part 1 is applicable, except as follows: Additional definitions: 3.101 router tool designed to be fitted with rotary cutter and with a base that allows contr

43、ol of cutting slots into or shaping the edge of various materials 3.102 trimmer tool designed to be fitted with rotary cutter and a base that allows for control of trimming the edge of laminate sheet or similar materials 4 General requirements This clause of Part 1 is applicable. 5 General condition

44、s for the tests This clause of Part 1 is applicable. 6 Environmental requirements This clause of Part 1 is applicable except as follows: 6.1.2.4 Modification: Routers and trimmers are suspended. The base plate of the tool shall be horizontal. BS EN 60745-2-17:2010EN 60745-2-17:2010 (E)- 7 -7 Classif

45、ication This clause of Part 1 is applicable. 6.1.2.5 Modification: Routers and trimmers are tested at no-load. 6.2 Vibration 6.2.4.2 Location of the measurement Addition: Figure Z101 shows the positions at both handles. 6.2.6.3 Operating conditions Modification: Trimmers are tested at no-load. Route

46、rs are tested under load observing the conditions shown in Table Z101. Table Z101 Test conditions Orientation Cutting grooves in a horizontal piece of medium density fibreboard (MDF) having the minimum dimensions 800 mm (length) x 400 mm (width) x 30 mm (depth). The board is fixed on a bench by scre

47、ws, clamps, air cylinders or the like with a resilient material between bench and workpiece Tool bit 12 mm straight sided bit as specified for MDF Feed force As necessary for smoothly working without overloading the machine. Apply equal force to both handles avoiding excessive gripping forces Test c

48、ycle Cutting a 10 mm deep groove across the 400 mm width of the MDF. Distance between grooves to be 10 mm using the guide fence if supplied 6.2.7.2 Declaration of the vibration total value Addition: The vibration total value ahof the handle with the highest emission and the uncertainty K shall be de

49、clared. BS EN 60745-2-17:2010EN 60745-2-17:2010 (E) - 8 -8 Marking and instructions This clause of Part 1 is applicable except as follows: 8.1 Addition: rated no-load speed in revolutions per minute. 8.12.1.1 Addition: Hold power tool by insulated gripping surfaces, because the cutter may contact its own cord. Cutting a “live“ wire may make exposed metal parts of the power tool “live“ and shock the operator. Use clamps or another practical way to secure and support the w