EN 60704-2-3-2002 en Household and similar electrical appliances C Test code for the determination of airborne acoustical noise Part 2-3 Particular requirements for dishwashers (In.pdf

《EN 60704-2-3-2002 en Household and similar electrical appliances C Test code for the determination of airborne acoustical noise Part 2-3 Particular requirements for dishwashers (In.pdf》由会员分享，可在线阅读，更多相关《EN 60704-2-3-2002 en Household and similar electrical appliances C Test code for the determination of airborne acoustical noise Part 2-3 Particular requirements for dishwashers (In.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60704-2-3:2002 IEC 60704-2-3:2001Incorporating Amendment No. 1Household and similar electrical appliances Test code for the determination of airborne acoustical noise Part 2-3: Particular requirements for dishwashersThe European Standard EN 60704-2-3:2002, with the incorporatio

2、n of amendment A1:2005, has the status of a British StandardICS 17.140.20; 97.040.40g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60704-2-3:

3、2002This British Standard was published under the authority of the Standards Policy and Strategy Committee on 1 May 2002 BSI 7 March 2006ISBN 0 580 39579 0National forewordThis British Standard is the official English language version of EN 60704-2-3:2002, including amendment A1:2005. It is identica

4、l with IEC 60704-2-3:2001. It supersedes BS EN 60704-2-3:1995 which will be withdrawn on 2005-03-01.The start and finish of text introduced or altered by CENELEC amendment is indicated in the text by tags . Tags indicating changes to CENELEC text carry the number of the CENELEC amendment. For exampl

5、e, text altered by CENELEC amendment A1 is indicated in the text by .The UK participation in its preparation was entrusted by Technical Committee CPL/59, Performance of household electrical appliances, to Subcommittee CPL/59/1, Dishwashers and washing machines, which has the responsibility to: A lis

6、t of organizations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standa

7、rds Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard d

8、oes not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European develop

9、ments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued

10、since publicationAmd. No. Date Comments15971 March 2006 See national forewordEUROPEAN STANDARD EN 60704-2-3NORME EUROPENNEEUROPISCHE NORMMarch 2002CENELECEuropean Committee for Electrotechnical StandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Nor

11、mungCentral Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.ICS 17.140.20;97.040.40 Supersedes EN 60704-2-3:1994English versionHousehold and similar electrical appliances Test code for th

12、e determination of airborne acoustical noisePart 2-3: Particular requirements for dishwashers(IEC 60704-2-3:2001)Appareils lectrodomestiqueset analogues Code dessai pour ladtermination du bruit arienPartie 2-3: Rgles particulirespour les lave-vaisselle(CEI 60704-2-3:2001)Elektrische Gerte fr denHaus

13、gebrauch und hnliche Zwecke -Prfvorschrift fr die Bestimmungder LuftschallemissionTeil 2-3: Besondere Anforderungenfr Geschirrsplmaschinen(IEC 60704-2-3:2001)+ A1August 2005(includes amendment A1:2005) (inclut lamendement A1:2005) (enthlt nderung A1:2005) This European Standard was approved by CENEL

14、EC on 2002-03-01; amendment A1:2005 was approved by CENELEC on 2005-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bib

15、liographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibil

16、ity of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I

17、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Ref. No. EN 60704-2-3:2002 + A1:2005 E Page 2EN 6070423:2002Foreword The text of document 59A/103/FDIS, future edition 2 of IEC 6070

18、4-2-3, prepared by SC 59A, Electric dishwashers, of IEC TC 59, Performance of household electrical appliances, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60704-2-3 on 2002-03-01. This European Standard supersedes EN 60704-2-3:1994. The following dates were fixed

19、: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2005-03-01 This Part 2-3 is to be used in conjuncti

20、on with EN 60704-1:1997. This Part 2-3 supplements or modifies the corresponding clauses of EN 60704-1. When a particular subclause of Part 1 is not mentioned in this Part 2-3, that subclause applies as far as is reasonable. Where this Part 2-3 states “addition“, “modification“ or “replacement“, the

21、 relevant text of Part 1 is to be adapted accordingly. Subclauses or figures which are additional to those in Part 1 are numbered starting from 101. Annexes designated “normative“ are part of the body of the standard. In this standard, annex A is normative. _ Endorsement notice The text of the Inter

22、national Standard IEC 60704-2-3:2001 was approved by CENELEC as a European Standard without any modification. _ Foreword to amendment A1 The text of document 59A/120/FDIS, future amendment 1 to IEC 60704-2-3:2001, prepared by SC 59A, Electric dishwashers, of IEC TC 59, Performance of household elect

23、rical appliances, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60704-2-3:2002 on 2005-07-01. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publication of an identical national standard

24、 or by endorsement (dop) 2006-04-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2008-07-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of amendment 1:2005 to the International Standard IEC 60704-2-3:2001 was approved by

25、CENELEC as an amendment to the European Standard without any modification. _ CONTENTSINTRODUCTION.41 Scope and object52 Normative references .53 Terms and definitions .64 Measurement methods and acoustical environments 65 Instrumentation 76 Operation and location of appliances under test .77 Measure

26、ment of sound pressure levels. 98 Calculation of sound pressure and sound power levels.109 Information to be recorded1010 Information to be reported 10Annex A (normative) Standard test table12Bibliography13Annex ZA (normative) Normative references to international publications with theircorrespondin

27、g European publications.14Figure 101 Test enclosure .11Page 3EN 6070423:2002INTRODUCTIONThe measuring conditions specified in this Part 2-3 provide for sufficient accuracy indetermining the noise emitted, and comparing the results of measurements taken by differentlaboratories, whilst simulating as

28、far as possible the practical use of dishwashers.To avoid unsteadiness caused by foaming, the tests are carried out with unsoiled loads andwithout detergents or rinsing aids.It is recommended to consider the determination of noise levels as part of a comprehensivetesting procedure covering many aspe

29、cts of properties and performance of dishwashers.Compared to the first edition (1987) of this Part 2, the second edition additionally considersthe noise of water supply, drainage, pre-wash and intermediate rinse. Therefore the operatingconditions during these operations shall be observed carefully.N

30、OTE As stated in the introduction to IEC 60704-1, this test code is concerned with airborne noise only.Page 4EN 6070423:2002HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES TEST CODE FOR THE DETERMINATION OF AIRBORNEACOUSTICAL NOISE Part 2-3: Particular requirements for dishwashers1 Scope and objectThis

31、clause of Part 1 is applicable except as follows:1.1 Scope1.1.1 GeneralReplacement:These particular requirements apply to single-unit electric dishwashers for household andsimilar use, with or without automatic programme control, for cold and/or hot water supply, fordetachable or permanent connectio

32、n to water supply or sewage systems, intended for placingon the floor against a wall, for building-in or placing under a counter, a kitchen worktop orunder a sink, for wall-mounting or on a counter.Limitations for the use of this test code are given in 1.1.1 of IEC 60704-1.1.1.2 Types of noiseReplac

33、ement:ISO 3743-1, ISO 3743-2 and ISO 3744 can be used for measuring noise emitted by dishwashers.1.1.3 Size of the sourceReplacement:The method specified in ISO 3744 is applicable to noise sources of any size. When applyingISO 3743-1 and ISO 3743-2, care should be taken that the maximum size of the

34、dishwasherunder test fulfils the requirements specified in 1.3 of ISO 3743-1 and ISO 3743-2.1.2 ObjectAddition:Requirements for the declaration of noise emission values are not within the scope of thisstandard.NOTE For determining and verifying noise emission values declared in product specification

35、s, see IEC 60704-3.2 Normative referencesThis clause of Part 1 is applicable except as follows:NOTE See bibliography at the end of the text.Page 5EN 6070423:2002Addition:IEC 60436:2004, Electric dishwashers for household use Methods for measuring the performanceISO 3055:1985, Kitchen equipment Coord

36、inating sizes 3 Terms and definitionsThis clause of Part 1 is applicable except as follows.3.4operational cycleAddition:The operational cycle of a dishwasher begins with the start of the cycle by the operator andends when the programme indicator reaches the end positionAddition:3.101rated capacityth

37、e total number of place settings together with the serving pieces stated by the manufacturer,which can be washed and dried when loaded in accordance with the manufacturersinstructions3.102 place setting and serving piecestableware and pieces as defined in the dishwashers performance standard.NOTE Se

38、e annex A of IEC 60436, Ed.3.13.103 standard test load for noise measurementsthe whole number of complete place settings plus the corresponding serving pieces, whichtogether comprise the manufacturers rated capacity3.104standard test programme for noise measurementsthe same programme as used for mea

39、suring the cleaning performance, the drying performance and energy and water consumption, according to IEC 60436:2004.3.105dryingthe operational period during which the load is dried. Drying begins when the washing pumphas stopped after final rinse and ends with the end of the operational cycle4 Mea

40、surement methods and acoustical environmentsThis clause of Part 1 is applicable except as follows.4.2 Direct methodAddition:NOTE 101 If pure tone components are present in the noise emitted, proper precautions should be taken asspecified in ISO 3743-2._1In preparation.Page 6EN 6070423:2002NOTE 101 U

41、sually this programme is the one recommended by the manufacturer for normally soiled load, usingnormal tableware, excluding cooking utensils. 4.3 Comparison methodAddition:NOTE 101 If pure tone components are present in the noise emitted, proper precautions should be taken asspecified in ISO 3743-1

42、and ISO 3743-2.5 InstrumentationThis clause of Part 1 is applicable.6 Operation and location of appliances under testThis clause of Part 1 is applicable except as follows:6.1 Equipping and pre-conditioning of appliances6.1.3 Replacement:Prior to commencing measurements, the inner surfaces of the app

43、liance and filters shall beclean and the salt container, if included, shall be filled with water. Then the appliance shall beoperated for at least two programme cycles as specified in 3.104, with or without load.6.1.4 Not applicable.6.2 Supply of electric energy and of water or gas6.2.2 Not applicab

44、le.6.2.3 Not applicable6.2.4Replacement:Dishwashers designed for either cold or hot water supply shall be supplied with cold water.The water hardness may be neglected.For noise measurements the static water pressure during filling shall be (240 50) kPa, ifnot contradictory to the manufacturers instr

45、uctions. The temperature of cold water shall be(15 5) C and the temperature of hot water shall be (55 5) C.NOTE When, in some countries, the water supply pressure/temperature differs from the water supply pressure/temperature of the country concerned, measurements carried out at rated pressure/tempe

46、rature may be misleadingfor the consumer. In this case, additional measurements may be necessary. If the test pressure/temperature differsfrom the rated pressure/temperature, this should be reported.6.4 Loading and operating of appliances during tests6.4.2Replacement:The test load shall be dry and a

47、t room temperature when the test programme starts.The appliance under test shall be at room temperature when the test programme starts.Page 7EN 6070423:2002The appliance shall be operated according to 3.104 and shall be loaded according to 3.103.The test must be carried out with unsoiled loads and w

48、ithout detergents and rinsing aids.If the manufacturers instructions clearly describe the loading with the rated capacity, theinstructions shall be followed; otherwise the principles of 3.103 have to be followed. In thelatter case, at least two series of measurements shall be carried out. For the se

49、cond or thefollowing series of measurements, the load shall be reasonably redistributed, following as faras possible the hints given by the manufacturer for general use.If the dishwasher involves a regulator to adjust spray-force, water pressure shall be regulatedaccording to the manufacturers instructions for the standard test programme (see 3.104).Care shall be taken to prevent avoidable noise by rattling of tableware through collision bywater jets or spray