EN 60384-4-2-2007 en Fixed capacitors for use in electronic equipment - Part 4-2 Blank detail specification - Fixed aluminium electrolytic capacitors with solid (MnO2) electrolyte .pdf

《EN 60384-4-2-2007 en Fixed capacitors for use in electronic equipment - Part 4-2 Blank detail specification - Fixed aluminium electrolytic capacitors with solid (MnO2) electrolyte .pdf》由会员分享，可在线阅读，更多相关《EN 60384-4-2-2007 en Fixed capacitors for use in electronic equipment - Part 4-2 Blank detail specification - Fixed aluminium electrolytic capacitors with solid (MnO2) electrolyte .pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60384-4-2:2007Fixed capacitors for use in electronic equipment Part 4-2: Blank detail specification Fixed aluminium electrolytic capacitors with solid (MnO2) electrolyte Assessment level EZICS 31.060.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g4

2、8g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Incorporating orrigendumApril 2009cBS EN 60384-4-2:2007This British Standard waspublished under the authorityof the Standards Policy andStrategy Committee on 31 March 2008 BSI

3、2009National forewordThe UK participation in its preparation was entrusted to Technical CommitteeEPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include al

4、l the necessary provisions of acontract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity fromlegal obligations. Amendments/corrigenda issued since publicationThis British Standard is the UK implementation of EN 60384-4-2:2007, incorporating

5、 corrigendum April 2009. It is identical to IEC 60384-4-2:2007. Together with BS EN 60384-4:2007 and BS EN 60384-4-1:2007 it supersedes BS QC 300300:1998 which is withdrawn. Together with BS EN 60384-4-1:2007 it partially supersedes BS EN 130301:2002, which is withdrawn.Date Comments Supersession te

6、xt updated in National forewordISBN 978 0 580 67718 230 June 2009 EUROPEAN STANDARD EN 60384-4-2 NORME EUROPENNE EUROPISCHE NORM May 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung C

7、entral Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-4-2:2007 E ICS 31.060.50 English version Fixed capacitors for use in electronic equipment - Part 4-2: Blank detai

8、l specification - Fixed aluminium electrolytic capacitors with solid (MnO2) electrolyte - Assessment level EZ (IEC 60384-4-2:2007) Condensateurs fixes utiliss dans les quipements lectroniques - Partie 4-2: Spcification particulire cadre - Condensateurs fixes lectrolytiques en aluminium lectrolyte so

9、lide (MnO2) - Niveau dassurance de la qualit EZ (CEI 60384-4-2:2007) Festkondensatoren zur Verwendung in Gerten der Elektronik - Teil 4-2: Vordruck fr Bauartspezifikation -Aluminium-Elektrolyt-Kondensatoren mit festem (MnO2) Elektrolyten - Bewertungsstufe EZ (IEC 60384-4-2:2007) This European Standa

10、rd was approved by CENELEC on 2007-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin

11、g such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its

12、own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, It

13、aly, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Incorporating Corrigendum April 2009Foreword The text of document 40/1763/CDV, future edition 2 of IEC 60384-4-2, prepared by IEC TC 4

14、0, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel Unique Acceptance Procedure and was approved by CENELEC as EN 60384-4-2 on 2007-04-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of

15、 an identical national standard or by endorsement (dop) 2008-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2010-04-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60384-4-2:2007 was approved

16、 by CENELEC as a European Standard without any modification. _ EN 60384-4-2:2007 2 BS EN 60384-4-2:2007FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 4-2: Blank detail specification Fixed aluminium electrolytic capacitors with solid (MnO2) electrolyte Assessment level EZ Blank detail specific

17、ation A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC

18、 specifications nor shall they be so described. In the preparation of detail specifications, the contents of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position

19、indicated. Identification of the detail specification 1 The International Electrotechnical Commission or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, data of issue and any further in

20、formation required by the national system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (when appli

21、cable). NOTE When the capacitor is not designed for use in printed board applications, this is clearly stated in the detail specification in this position. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international document

22、s for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Application or group of applications covered and/or assessment level. NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional specification. This imp

23、lies that one blank detail specification may be used in combination with several assessment levels, provided the grouping of the tests does not change. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. EN 60384-4-2:2007 3 BS EN 60384-4-2:2007

24、1 IEC 60384-4-2- XXX QC 300302- XXX 2 IEC 60384-4-2 QC 300302 4 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: IEC 60384-1 IEC 60384-4 3 FIXED ALUMINIUM ELECTROLYTIC CAPACITORS WITH SOLID (MnO2) ELECTROLYTE 5 6 Outline drawing: (see Table 1) (angle projection) 7 (Other shapes are perm

25、itted within the dimensions given.) Assessment level(s): EZ Performance grade: 8 Information on the availability of components qualified to this detail specification is given in the IEC QC 001005. 9 EN 60384-4-2:2007 4 BS EN 60384-4-2:20071 General data 1.1 Recommended method(s) of mounting (to be i

26、nserted) See 1.4.2 of IEC 60384-4. 1.2 Di006Densions Table 1 Case size reference and dimensions Dimensions mm Case size reference L H d NOTE 1 When there is no case size reference, Table 1 may be omitted and the dimensions should be given in Table 2, which then becomes Table 1. NOTE 2 The dimensions

27、 should be given as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteristics Capacitance range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category Rated temperature Rated ripple

28、 current (see Table 3) Tangent of loss angle (see Table 3) NOTE Instead of the tangent of loss angle (tan ), the equivalent series resistance ESR may be specified in accordance with 4.3.3.2d) of IEC 60384-4. Leakage current Impedance (if applicable) (see Table 3) Reverse voltage (if required) Insula

29、tion resistance (if applicable) Table 2 Values of capacitance and of voltage related to case sizes Rated voltage Category voltage* Case size Case size Case size Case size Rated capacitance F * If different from the rated voltage. EN 60384-4-2:2007 5 BS EN 60384-4-2:2007Table 3 Tangent of loss angle,

30、 impedance and rated ripple current URV CRF Tangent of loss angle at. C,. Hz Impedance at. C, . Hz (if applicable) Rated ripple current at. C,. Hz A 1.4 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edit

31、ion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-4, Fixed capacitors for use in electronic equipment Part 4: Sectional spe

32、cification: Aluminium electrolytic capacitors with solid (MnO2) and non-solid electrolyte IEC 60410, Sampling plans and procedures for inspection by attributes 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of 1.6 of IEC 60384-4. The details of

33、the marking of the component and package are given in full in the detail specification. 1.6 Ordering information Orders for capacitors covered by this specification shall contain, in clear or in coded form, the following minimum information. a) Rated capacitance. b) Tolerance on rated capacitance. c

34、) Rated d.c. voltage. d) Number and issue reference of the detail specification and style reference. 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the

35、 generic and/or sectional specification NOTE Additions or increased requirements should be specified only when essential. Table 4 Other characteristics This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectional specification. EN 6

36、0384-4-2:2007 6 BS EN 60384-4-2:20072 Inspection requirements 2.1 Procedures 2.1.1 For qualification approval, the procedures shall be in accordance with 3.4 of IEC 60384-4. 2.1.2 For quality conformance inspection, the test schedule (Table 5) includes sampling, periodicity, severities and requireme

37、nts. The formation of inspection lots is covered by 3.5.1 of the sectional specification. Table 5 Test schedule for qualification conformance inspection Subclause number and test Conditions of test IL n c Performance requirements aDcor NDcacccaGroup A inspection (lot-by-lot) Subgroup A0 ND 100 %e4.2

38、1 High surge current (if required by the detail specification) Subgroup A1 ND S-3dd0 4.2 Visual examination As in 4.2 Legible marking and as specified in 1.5 of this specification 4.2 Dimensions (gauging) As specified in Table 1 of this specification Subgroup A2 ND S-3dd0 4.3.1 Leakage Protective re

39、sistance: As in 4.3.1.2 4.3.2 Capacitance Frequency: Hz Within specified tolerance 4.3.3 Tangent of loss angle Frequency: Hz As in 4.3.3.2 4.3.4 Impedance (if applicable) Frequency: Hz Within limit specified in the detail specification a Subclause number of tests and performance requirements refer t

40、o IEC 60384-4 and Clause 1 of this specification. b Not applicable to capacitors with screw terminations or other terminations not designed to be soldered, as stated in the detail specifications. c In this table, IL = inspection level (IEC 60410) n = sample size c = permissible number of nonconformi

41、ng items p = periodicity in months D = destructive ND = non-destructived Number to be tested: sample size as directly allotted to the code letter for IL in Table 2A of IEC 60410. e100 % testing shall be followed by re-inspection by sampling in order to monitor outgoing quality level by non-conformin

42、g items per million (ppm). The sampling level shall be established by the manufacturer. For the calculation of ppm values any parametric failure shall be counted as a nonconforming item. If one or more nonconforming items occur in a sample, this lot shall be rejected. EN 60384-4-2:2007 7 BS EN 60384

43、-4-2:2007Table 5 (continued) Subclause number and test Conditions of test IL n c Performance requirements aDcor NDcacccaeGroup B inspection (lot-by-lot) Subgroup B1 ND S-3dd0 4.6 SolderabilitybMethod:. Good tinning as evidenced by free flowing of the solder with wetting of the terminations or meet t

44、he required parameter(s) in the detail specification as applicable Subgroup B2 ND S-3dd0 4.19 Characteristics at high and low temperature The capacitors shall be measured at each temperature step Step 1: 20 C Impedance (at same frequency as Step 2) Step 2: Lower category temperature Impedance Ratio

45、with respect to value in Step 1: 2 times a Subclause number of tests and performance requirements refer to IEC 60384-4 and Clause 1 of this specification. b Not applicable to capacitors with screw terminations or other terminations not designed to be soldered, as stated in the detail specifications.

46、 c In this table, IL = inspection level (IEC 60410) n = sample size c = permissible number of non-conforming items p = periodicity in months D = destructive ND = non-destructived Number to be tested: sample size as directly allotted to the code letter for IL in Table 2A of IEC 60410. EN 60384-4-2:20

47、07 8 BS EN 60384-4-2:2007Table 5 (continued) Sample size and criterion of acceptability cSubclause number and test aD or ND Conditions of test ap n c Performance requirements aGroup C inspection (periodic) Subgroup C1A D 6 9 0 Part of sample of subgroup C1 4.2 Dimensions (detail) See detail specific

48、ation 4.4.1 Initial measurement Capacitance 4.4 Robustness of terminations Visual examination Method: Severity: No visible damage 4.5 Resistance to soldering heat* No pre-drying Method: 4.5.2 Final measurements Visual examination No visible damage Legible marking Capacitance C/C 5 % of value measure

49、d in 4.4.1 Subgroup C1B D 6 18 0 Other part of sample of group C1 4.7.1 Initial measurement 4.7 Rapid change of temperature Capacitance TA= lower category temperature TB= upper category temperature Five cycles Duration t1= 30 min or 3 h Recovery: 16 h 4.7.3 Final measurements Visual examination No visible damage Leakage current As in 4.3.1 Tangent of loss angle As in 4.3.3 Impedance Within the limit specified in