EN 60384-26-1-2010 en Fixed capacitors for use in electronic equipment - Part 26-1 Blank detail specification - Fixed aluminum electrolytic capacitors with conductive polymer solid.pdf

《EN 60384-26-1-2010 en Fixed capacitors for use in electronic equipment - Part 26-1 Blank detail specification - Fixed aluminum electrolytic capacitors with conductive polymer solid.pdf》由会员分享，可在线阅读，更多相关《EN 60384-26-1-2010 en Fixed capacitors for use in electronic equipment - Part 26-1 Blank detail specification - Fixed aluminum electrolytic capacitors with conductive polymer solid.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFixed capacitors for use in electronic equipmentPart 26-1: Blank detail specification Fixed aluminum electrolytic capacitors with conductive polymer solid electrolyte Assessment

2、level EZBS EN 60384-26-1:2010National forewordThis British Standard is the UK implementation of EN 60384-26-1:2010. It isidentical to IEC 60384-26-1:2010.The UK participation in its preparation was entrusted to Technical CommitteeEPL/40X, Capacitors and resistors for electronic equipment.A list of o

3、rganizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2010 ISBN 978 0 580 65140 3 ICS 31.060.50Compliance with a British Stan

4、dard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2010.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60384-26-1:2010EUROPEAN STANDARD EN 60384

5、-26-1 NORME EUROPENNE EUROPISCHE NORM October 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of expl

6、oitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-26-1:2010 E ICS 31.060.50 English version Fixed capacitors for use in electronic equipment - Part 26-1: Blank detail specification - Fixed aluminum electrolytic capacitors with conductive polymer solid el

7、ectrolyte - Assessment level EZ (IEC 60384-26-1:2010) Condensateurs fixes utiliss dans les quipements lectroniques - Partie 26-1: Spcification particulire cadre - Condensateurs fixes lectrolytiques en aluminium electrolyte solide en polymre conducteur - Niveau dassurance de la qualit EZ (CEI 60384-2

8、6-1:2010) Festkondensatoren zu Verwendung in Gerten der Elektronik - Teil 26-1: Vordruck fr Bauartspezifikation - Aluminium-Elektrolyt-Kondensatoren mit leitfhigem Polymerfestkrper-Elektrolyten - Qualittsbewertungsstufe EZ (IEC 60384-26-1:2010) This European Standard was approved by CENELEC on 2010-

9、10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be ob

10、tained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Ce

11、ntral Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lu

12、xembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 60384-26-1:2010 - 2 - Foreword The text of document 40/2053/FDIS, future edition 1 of IEC 60384-26-1, prepared by IEC TC 40, Capacitors and resistors for ele

13、ctronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-26-1 on 2010-10-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identi

14、fying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-07-01 latest date by which the national standards conflicting with the EN have to be

15、withdrawn (dow) 2013-10-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60384-26-1:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60384-26-1:2010- 3 - EN 60384-26-1:2010 Annex ZA (normative) Normative refer

16、ences to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (i

17、ncluding any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60068-2-20 2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability

18、and resistance to soldering heat of devices with leads EN 60068-2-20 2008 IEC 60384-1 2008 Fixed capacitors for use in electronic equipment - Part 1: Generic specification EN 60384-1 2009 IEC 60384-26 2010 Fixed capacitors for use in electronic equipment - Part 26: Sectional specification - Fixed al

19、uminium electrolytic capacitors with conductive polymer solid electrolyte EN 60384-26 2010 BS EN 60384-26-1:2010 4 60384-26-1 IEC:2010 CONTENTS 1 General data 6 1.1 Recommended method(s) of mounting (to be inserted) 6 1.2 Dimensions .6 1.3 Rating and characteristics .7 1.4 Normative references 7 1.5

20、 Marking .8 1.6 Ordering information8 1.7 Certified records of released lots .8 1.8 Additional information (not for inspection)8 1.9 Other requirements for generic or sectional specifications .8 2 Inspection requirements .8 2.1 Procedures8 2.1.1 Qualification approval 8 2.1.2 Quality conformance ins

21、pection .8 Bibliography17 Table 1 Case size reference and dimensions .6 Table 2 Values of capacitance and of voltage related to case sizes .7 Table 3 Characteristics 7 Table 4 Other requests (other characteristics) .8 Table 5 Test schedule for quality conformance inspection9 BS EN 60384-26-1:2010603

22、84-26-1 IEC:2010 5 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 26-1: Blank detail specification Fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte Assessment level EZ Blank detail specification A blank detail specification is a supplementary document to the s

23、ectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specification nor shall they so be described. In the preparation of de

24、tail specifications the contents of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification 1 The “Internationa

25、l Electrotechnical Commission” or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and date of iss

26、ue of the IEC or National Generic Specification. 4 The number of the IEC or National blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (If applicable). 7 Outline drawing with main dimensions which are of

27、importance for interchange ability and / or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an appendix to the detail specification. 8 Application or group of applications covered and / or assessment level. 9 Reference data on the most i

28、mportant properties, to allow comparison between the various capacitor types. BS EN 60384-26-1:2010 6 60384-26-1 IEC:2010 124 IEC 60384-26-1 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 5 Aluminium electrolytic capacitors with conductive polymer solid electrolyte 6 Outline drawing

29、: (see Table 1) ( angle projection) 7 8 Assessment level(s): EZ Information on the availability of components qualified to this detail specification is given in the qualified product list. 9 1 General data 1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-26, 1.4.2 1.2 Dimensions

30、Table 1 Case size reference and dimensions Dimensions in millimeters Case size reference L W H d NOTE 1 When there is no case-size reference, decline Table 1 and give the dimensions in Table 2 as Table 1. NOTE 2 Indicate the dimensions as maximum dimension or as nominal dimensions with tolerance. BS

31、 EN 60384-26-1:201060384-26-1 IEC:2010 7 1.3 Rating and characteristics Ratings and characteristics are as listed below. Nominal capacitance range (see Table 2) Tolerance on nominal capacitance Rated voltage (see Table 2) Climatic category Rated temperature Rated ripple current (see Table 3) Tangent

32、 of loss angle (see Table 3) Leakage current (see Table 3) Equivalent series resistance (see Table 3) Reverse voltage (if required in the detail specification) Table 2 Values of capacitance and of voltage related to case sizes Rated voltage Case size Case size Case size Case size Case size Nominal c

33、apacitance Table 3 Characteristics URCNTangent of loss angle at C, . Hz Leakage current at C Equivalent series resistance at C, Hz Rated ripple current at C, Hz V F Hz A mA or A 1.4 Normative references The following referenced documents are indispensable for the application of this document. For da

34、ted references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-20:2008, Environmental testing Part 2-20: Tests Test T Test methods for solderability and resistance to soldering heat of devices with

35、 leads IEC 60384-1:2008, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-26:1Fixed capacitors for use in electronic equipment Part 26: Sectional specification Fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte 1To be published.

36、BS EN 60384-26-1:2010 8 60384-26-1 IEC:2010 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of IEC 60384-26, 1.6. NOTE The details of the marking of the component and package should be given in full in the detail specification. 1.6 Ordering infor

37、mation Orders for capacitors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) nominal capacitance; b) tolerance on nominal capacitance; c) rated d.c. voltage; d) issue number and edition of the detail specification and type of capacitors.

38、1.7 Certified records of released lots Required / not required NOTE Clearly state a necessity for customer requests. 1.8 Additional information (not for inspection) NOTE Clearly state a necessity for additional information. 1.9 Other requirements for generic or sectional specifications NOTE Other re

39、quirements should be specified to those that are absolutely necessary. See Table 4. Table 4 Other requests (other characteristics) This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectional specification. 2 Inspection requirements

40、 2.1 Procedures 2.1.1 Qualification approval For qualification approval, the procedures shall be in accordance with IEC 60384-26, 3.4. 2.1.2 Quality conformance inspection For quality conformance inspection, the test schedule (Table 5) includes sampling, periodicity, severities and requirements. The

41、 formation of inspection lots is covered by IEC 60384-26, 3.5.1. BS EN 60384-26-1:201060384-26-1 IEC:2010 9 Table 5 Test schedule for quality conformance inspection Sample number and criteria cSubclause number and test aD or ND bTest condition aIL n c Requirements aGroup A inspection (each lot) Subg

42、roup A0 4.22 High surge current ND See detail specification 4.4.1 Leakage current Protective resistor: 1 000 0,2 CNUR(A) or 500 A (whichever is greater) 4.4.2 Capacitance Frequency: Hz Bias voltage: V Within specified tolerance 4.4.3 Tangent of loss angle (tan ) Frequency: Hz Bias voltage: V See Tab

43、le 3 4.4.4 Equivalent series resistance (ESR) Frequency: 100 kHz 100 %dSee Table 3 Subgroup A1 4.3 Visual inspection ND S-3 f 0 See IEC 60384-26, 4.3.2 Subgroup A2 4.3 Dimensions (detail)eND S-3 f 0 See Table 1 Group B inspection (each lot) 4.7 Solderability D Test method and severity: As in IEC 600

44、68-2-20, Test Ta, method 1 S-3 f 0 4.7.2 Final measurement Visual inspection See 4.7.2 4.18 Solvent resistance of marking gSolvent: 2-propanol Solvent temp: 23 C 5 C Method: 1 Rubbing material: cotton wool Recovery time: aSubclause numbers of tests and performance requirements refer to IEC 60384-26

45、and Clause 1 of this specification. b In this table: D = destructive, ND = non-destructive cIn this table: IL = inspection level, n = sample size, c = acceptance criterion (permitted number of non-conforming items) The permissible number of non-conforming items indicates acceptance criteria. In case

46、 non-conforming item(s) is equal or less than the number, this lot shall be accepted.d 100 % testing shall be followed by re-inspection by sampling in order to monitor outgoing qualify level by non-confirming items per million. The sampling level shall be established by each manufacturer. For the ca

47、lculation of parts per million values, any parametric failure shall be counted as a non-conforming item. If one or more non-conforming items occur in a sample, this lot shall be rejected. eThis test may be replaced by in-production testing if the manufacturer installs statistical process control (SP

48、C) on dimensional measurements or other mechanisms to avoid parts exceeding the limits. f Inspection levels are selected from IEC 60410.g If required in the detail specification.BS EN 60384-26-1:2010 10 60384-26-1 IEC:2010 Table 5 (continued) Sample number and criteria cSubclause number and test aD

49、or ND bTest condition ap n c Requirements aSubgroup C1A 4.3 Dimension (detail) D 6 12 0 See detail specification 4.5.1 Initial measurement Capacitance Visual inspection No visible damage 4.5 Terminal strength Method and Criteria See IEC 60384-1, 4.13 Tension test Bending test 4.6 Resistance to soldering heat Non-preconditioning (Drying) 4.6.1 I