EN 60384-19-1-2006 en Fixed capacitors for use in electronic equipment Part 19-1 Blank detail specification - Fixed metallized polyethylene-terephthalate film dielectric surface mo.pdf

《EN 60384-19-1-2006 en Fixed capacitors for use in electronic equipment Part 19-1 Blank detail specification - Fixed metallized polyethylene-terephthalate film dielectric surface mo.pdf》由会员分享，可在线阅读，更多相关《EN 60384-19-1-2006 en Fixed capacitors for use in electronic equipment Part 19-1 Blank detail specification - Fixed metallized polyethylene-terephthalate film dielectric surface mo.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60384-19-1:2006Incorporating corrigendum no. 1Fixed capacitors for use in electronic equipment Part 19-1: Blank detail specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors Assessment level EZ The European Standard EN 60384-19-1

2、:2006 has the status of a British StandardICS 31.060.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60384-19-1:2006This British Standard wa

3、s published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2007ISBN 978 0 580 60801 8National forewordThis British Standard is the UK implementation of EN 60384-19-1:2006, incorporating corrigendum November 2006. It is identical with IEC 60384-19-1:2006. It su

4、persedes BS CECC 32201:1988 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication do

5、es not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date Comments17525 Corrigendum No. 131 December 2007 R

6、eplacement of last paragraph in foreword. Addition of Annex ZAEUROPEAN STANDARD EN 60384-19-1 NORME EUROPENNE EUROPISCHE NORM March 2006 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Ce

7、ntral Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-19-1:2006 E ICS 31.060.10 Incorporating corrigendum November 2006English version Fixed capacitors for use in elect

8、ronic equipment Part 19-1: Blank detail specification - Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors - Assessment level EZ (IEC 60384-19-1:2006) Condensateurs fixes utiliss dans les quipements lectroniques Partie 19-1: Spcification particulire cadre - Con

9、densateurs fixes chipses pour courant continu dilectrique en film de polytrphtalate dthylne mtallis - Niveau dassurance EZ (CEI 60384-19-1:2006) Festkondensatoren zur Verwendung in Gerten der Elektronik Teil 19-1: Vordruck fr Bauartspezifikation - Oberflchenmontierbare Gleichspannungs-Kondensatoren

10、mit metallisierter Polyethylen-Terephtalat-Folie als Dielektrikum - Qualittsbewertungsstufe EZ (IEC 60384-19-1:2006) This European Standard was approved by CENELEC on 2006-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving t

11、his European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versi

12、ons (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of

13、Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Forewor

14、d The text of document 40/1623/FDIS, future edition 2 of IEC 60384-19-1, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-19-1 on 2006-02-01. The following dates were fixed: latest date by

15、 which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-11-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-02-01 Annex ZA has been added by CENELEC. _ Endorsement notice

16、 The text of the International Standard IEC 60384-19-1:2006 was approved by CENELEC as a European Standard without any modification. _ EN 60384-19-1:2006 2 3 EN 60384-19-1:2006 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 19-1: Blank detail specification Fixed metallized polyethylene-tereph

17、thalate film dielectric surface mount d.c. capacitors Assessment level EZ Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specificati

18、ons not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of detail specifications, the content of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on t

19、he first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission“ or the National Standards Organization under whose authority the detail specification is drafted. 2 Th

20、e IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the capacitor 5

21、 A short description of the type of capacitor. 6 Information on typical construction (when applicable). When the capacitor is not designed for use in printed-board applications, this shall be clearly stated in the detail specification in this position. 7 Outline drawing with main dimensions which ar

22、e of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Application or group of applications covered and/or assessment level. NOTE The assessment level(s) to b

23、e used in a detail specification are selected from 3.5.4 of the sectional specification. This implies that one blank detail specification may be used in combination with several assessment levels, provided the grouping of the tests does not change. 9 Reference data on the most important properties,

24、to allow comparison between the various capacitor types. EN 60384-19-1:2006 4 1 IEC 60384-19-1-XXX 2 QC 302201-XXX IEC 60384-19-1 4 QC 302201 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 FIXED METALLIZED 5 POLYETHYLENE-TEREPHTHALATE FILM DIELECTRIC DC SURFACE MOUNT CAPACITORS 6 Ou

25、tline drawing: (see Table 1) .angle projection 7 Other shapes are permitted within the dimensions given. Assessment level(s): EZ 8 Information on the availability of components qualified to this detail specification is given in IEC QC 001005 (9) 1 General data 1.1 Recommended method(s) of mounting (

26、to be inserted) See IEC 60384-19, 1.4.2 1.2 Dimensions Table 1 Case size reference and dimensions Dimensions mm Case size reference L1max W1max H1max L2L3L4min When there is no case size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1. The d

27、imensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 5 EN 60384-19-1:2006 1.3 Ratings and characteristics Capacitance range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category R

28、ated temperature Max. a.c. voltage (if applicable) Max. pulse load (if applicable) Tangent of loss angle Insulation resistance Table 2 Values of capacitance and of voltage related to case sizes Rated voltage Category voltageaCase size Case size Case size Case size Rated capacitance (in nF and/or F)

29、aIf different from the rated voltage. 1.4 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

30、nts) applies. IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-19, Fixed capacitors for use in electronic equipment Part 19: Sectional specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors IEC 6041

31、0, Sampling plans and procedures for inspection by attributes 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of IEC 60384-19, 1.6. The details of the marking of the component and package shall be given in full in the detail specification. 1.6 Or

32、dering information Orders for capacitors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) rated capacitance; b) tolerance on rated capacitance; EN 60384-19-1:2006 6 c) rated d.c. voltage; d) number and issue reference of the detail specifi

33、cation and style reference; e) packaging instructions. 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTE A

34、dditions or increased requirements should be specified only when essential. Table 3 Other characteristics This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectional specification. 7 EN 60384-19-1:2006 2 Inspection requirements 2.1

35、 Procedures 2.1.1 For qualification approval, the procedures shall be in accordance with the sectional specification, IEC 60384-19, 3.4. 2.1.2 For quality conformance Inspection, the test schedule (Table 4) includes sampling, periodicity, severities and requirements. The formation of inspection lots

36、 is covered by IEC 60384-19, 3.5.1. Table 4 Test schedule for quality conformance Inspection IL n c Subclause number and testa D or ND Conditions of testa c)Performance requirementsaGROUP A INSPECTION (Lot-by-lot) Subgroup A0 ND 100 % d)4.3.2 Capacitance Frequency : 1kHz for all capacitance values W

37、ithin specified tolerance 4.3.3 Tangent of loss angle Method : As in 4.3.3.2 4.3.1 Voltage proof (Test A) Measuring point 1a No breakdown or flashover. Self-healing breakdown allowed. 4.3.4 Insulation resistance (Test A) Measuring point 1a As in 4.3.4.3 Subgroup A1 ND S-3 b)0 4.2 Visual examination

38、As in 4.2.2 Legible marking (if applicable) and as specified in 1.5 of this specification Subgroup A2 ND S-3 b)0 4.2 Dimensions As specified in Table 1 of this specification GROUP B INSPECTION (Lot-by-lot) Subgroup B1 D S-3 b)0 4.7 Solderability No ageing Method: . 4.7.2 Final measurements Visual ex

39、amination As in 4.7.2 Subgroup B2 D S-3 b)0 4.14 Solvent resistance of the marking (if applicable)fSolvent: . Solvent temperature: . Method 1 Rubbing material: cotton wool Recovery: Legible marking EN 60384-19-1:2006 8 Table 4 (continued) Subclause number and testaD or ND Conditions of testaSample s

40、ize and acceptance criterioncPerformance requirementsap n c GROUP C INSPECTION (Periodic) Subgroup C1 D 3 12 0g)4.6 Resistance to soldering heat Method: 4.6.1 Initial measurements Capacitance 4.6.2 Test conditions Duration: If method 1 is applied, immersion and withdrawal speed shall be 25 mm/s 2,5

41、mm/s Recovery: 24 h 2 h 4.6.3 Finalmeasurements Visual examination As in 4.6.3 Capacitance C/C 3% of value measured in 4.6.1 4.13 Components solvent resistance (if applicable) Solvent: Solvent temperature Method 2 Recovery: See detail specification Subgroup C2 D 3 12 0g)4.5 Substrate bending test Su

42、bgroup C3 D 4.1 MountinghSubstrate material: i4.2.1 Visual examination As in detail specification 4.3.2 Capacitance C/C 2% of value measured before mounting 4.3.3 Tangent of loss angle Frequency: 1 kHz (for all capacitance values) 10 kHz for capacitors with CR 1 F (in addition, see 4.3.3.3) As in 4.

43、3.3 (Reference values for final measurements in subgroups C3.1, C3.3 and C3.4) 4.3.4 Insulation resistance As in 4.3.4.3 9 EN 60384-19-1:2006 Table 4 (continued) Subclause number and testa D or ND Conditions of testa Sample size and acceptance criterioncPerformance requirementsap n c Subgroup C3.1 D

44、 6 27 0g)4.4 Shear 4.8 Rapid change of temperature 4.8.1 Initial measurements Not required, see Subgroup C3 4.8.2 Test conditions TA = Lower category temperature TB= Upper category temperature Five cycles Duration t1= 30 min 4.8.3 Intermediate inspection Visual examination 4.9 Climatic sequence 4.9.

45、1 Initial measurements Not required, see Subgroup C3 4.9.2 Dry heat Temperature: upper category temperatureDuration: 16 h 4.9.3 Damp heat, cycle, test Db, first cycle 4.9.4 Cold Temperature: lower category temperature Duration: 2 h 4.9.5 Damp heat, cycle, test Db, remaining cycles Within 15 min afte

46、r removal from test chamber URto be applied for 1 min 4.9.6 Final measurements Visual examination No visible damage Legible marking Capacitance C/C 5 % of the value measured in Subgroup C3 Tangent of loss angle: at 10 kHz for CR 1 F Increase of tan : 0,005 for Grade 1 0,008 for Grade 2 at 1 kHz for

47、CR 1 F 0,003 for Grade 1 0,005 for Grade 2 compared to values measured in Subgroup C3 Insulation resistance 50 % of values in 4.3.4.3 Subgroup C3.2 D 6 15 0g)4.10 Damp heat, steady state 4.10.1 Initial measurements Not required, see Subgroup C3 EN 60384-19-1:2006 10 Table 4 (continued) Subclause num

48、ber and testa D or ND Conditions of testa Sample size and acceptance criterioncPerformance requirementsap n c 4.10.2 Final measurements Visual examination No visible damage Capacitance C/C 5 % of the value measured in Subgroup C3 Tangent of loss angle at 1 kHz Increase of tan : 0,005 compared to val

49、ues measured in Subgroup C3 Insulation resistance 50 % of values in 4.3.4.3 Subgroup C3.3 D 3 15 0g)4.11 Endurance 4.11.1 Initial measurements Not required, see Subgroup C3 4.11.2 Test conditions See 4.11.2, 4.11.3 and 4.11.4 4.11.5 Final measurements Visual examination No visible damage Legible marking Capacitance C/C 5 % for Grade 1 C/C