EN 60384-16-2005 en Fixed capacitors for use in electronic equipment Part 16 Sectional specification Fixed metallized polypropylene film dielectric d c capacitors《电子设备用固定电容器 第16部分 .pdf

《EN 60384-16-2005 en Fixed capacitors for use in electronic equipment Part 16 Sectional specification Fixed metallized polypropylene film dielectric d c capacitors《电子设备用固定电容器 第16部分 .pdf》由会员分享，可在线阅读，更多相关《EN 60384-16-2005 en Fixed capacitors for use in electronic equipment Part 16 Sectional specification Fixed metallized polypropylene film dielectric d c capacitors《电子设备用固定电容器 第16部分 .pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60384-16:2005Fixed capacitors for use in electronic equipment Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitorsICS 31.060.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g

2、40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Incorporating corrigendum March 2010National forewordThis British Standard is the UK implementation of EN 60384-16:2005. It was derived by CENELEC from IEC 60384-16:2005. It supersedes BS QC 301200:1983 and

3、BS EN 131200:2002 which are withdrawn.The CENELEC common modifications have been implemented at the appropriate places in the text and are indicated by tags (e.g. ).The UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment

4、.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from

5、 legal obligations.BS EN 60384-16:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 8 February 2006 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 March 2010 Supersession text amended ISBN 978 0 580 70372 0EUROPEAN S

6、TANDARD EN 60384-16 NORME EUROPENNE EUROPISCHE NORM December 2005 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2005 CENELEC -

7、 All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-16:2005 E ICS 31.060.30 Supersedes EN 131200:2002English version Fixed capacitors for use in electronic equipment Part 16: Sectional specification: Fixed metallized polypropylene film d

8、ielectric d.c. capacitors (IEC 60384-16:2005) Condensateurs fixes utiliss dans les quipements lectroniques Partie 16: Spcification intermdiaire: Condensateurs fixes pour courant continu dilectrique en film de polypropylne mtallis (CEI 60384-16:2005) Festkondensatoren zur Verwendung in Gerten der Ele

9、ktronik Teil 16: Rahmenspezifikation: Festkondensatoren mit metallisierter Polypropylen-Folie als Dielektrikum fr Gleichspannung (IEC 60384-16:2005) This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipu

10、late the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standar

11、d exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national

12、 electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingd

13、om. Foreword The text of document 40/1595/FDIS, future edition 2 of IEC 60384-16, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-16 on 2005-11-01. This European Standard supersedes EN 13

14、1200:2002. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-08-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2008-11-01

15、 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60384-16:2005 was approved by CENELEC as a European Standard without any modification. _ EN 60384-16:2005 2 BS EN 60384-16:2005 3 EN 60384-16:2005 CONTENTS 1 General5 1.1 Scope5 1.2 Object .5 1.3 Nor

16、mative references 5 1.4 Information to be given in a detail specification 6 1.5 Terms and definitions 7 1.6 Marking .8 2 Preferred ratings and characteristics.8 2.1 Preferred characteristics8 2.2 Preferred values of ratings.8 3 Quality assessment procedures 9 3.1 Primary stage of manufacture 9 3.2 S

17、tructurally similar components .9 3.3 Certified records of released lots9 3.4 Qualification approval 10 3.5 Quality conformance inspection .16 4 Test and measurement procedures .17 4.1 Visual examination and check of dimensions17 4.2 Electrical tests.18 4.3 Robustness of terminations21 4.4 Resistanc

18、e to soldering heat21 4.5 Solderability 21 4.6 Rapid change of temperature.21 4.7 Vibration21 4.8 Bump 22 4.9 Shock22 4.10 Climatic sequence .23 4.11 Damp heat, steady state 24 4.12 Endurance.24 4.13 Charge and discharge24 4.14 Component solvent resistance .26 4.15 Solvent resistance of the marking

19、26 Bibliography .27 Annex ZA (normative) Normative references to international publications with their corresponding European publications28 Table 1 Preferred values7 Table 2 Preferred combinations9 Table 3 Sampling plan together with numbers of permissible defectives for qualification approval test

20、s11 Table 4 Test schedule for qualification approval .12 Table 5 Lot-by-lot inspection 17 BS EN 60384-16:2005EN 60384-16:2005 4 Table 6 Periodic inspection 17 Table 7 Voltages to be applied .18 Table 8 Measurement requirements .19 Table 9 Insulation resistance requirements.19 Table 10 Correction fac

21、tors 20 Table 11 Characteristics at lower category temperature 20 Table 12 Characteristics at upper category temperature .20 Table 13 Preferred severities .22 Table 14 Test conditions 24 Table 15 Lead spacing.25 BS EN 60384-16:2005 5 EN 60384-16:2005 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT

22、Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors 1 General 1.1 Scope This part of IEC 60384 applies to fixed capacitors with metallized electrodes and poly-propylene dielectric for use in electronic equipment. These capacitors may have “self-healing pr

23、operties“ depending on conditions of use. They are mainly intended for use with direct voltage. Capacitors for alternating voltage and pulse applications are not included, but are covered by IEC 60384-17. The maximum power to be applied is 500 var at 50 Hz and the maximum peak voltage is 2 500 V. Tw

24、o performance grades of capacitors are covered, Grade 1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. Capacitors for electrical shock hazard protection (covered by IEC 60065) a

25、nd fluorescent lamp and motor capacitors (covered by IEC technical committee 33, and IEC technical committee 34). 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1 (1999) the appropriate quality assessment procedures, tests an

26、d measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher performance level, because lower performance levels are not permitte

27、d. 1.3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Prefe

28、rred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1, Environmental testing. Part 1: General and guidance IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-16-1, Fixed capacitors for use in electronic eq

29、uipment Part 16: Blank detail specification: Fixed metallized polypropylene film dielectric d.c. capacitors Assessment level E IEC 60410, Sampling plans and procedures for inspection by attributes ISO 3, Preferred numbers Series of preferred numbers BS EN 60384-16:2005EN 60384-16:2005 6 1.4 Informat

30、ion to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, t

31、hey shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. NOTE The information given in 1.4.1 may for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted s

32、hall preferably be selected from those given in the appropriate clause of this sectional specification. 1.4.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated

33、tolerances, which affect interchangeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres. Normally, the numerical values shall be given for the length of the body, the width and height of the body and the wire spacing, or for cyli

34、ndrical types, the body diameter, and the length and diameter of the terminations. When necessary, for example when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing

35、. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification 1.4.2 Mounting T

36、he detail specification shall specify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required i

37、n its use. In this case, the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specif

38、ication, together with the following: 1.4.3.1 Rated capacitance range See 2.2.1. NOTE When products approved to the detail specification may have different ranges, the following statement should be added: “The range of values available in each voltage range is given in IEC QC 001005. 1.4.3.2 Particu

39、lar characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and application purposes. BS EN 60384-16:2005 7 EN 60384-16:2005 1.4.3.3 Soldering The detail specification shall prescribe the test methods, severities and

40、 requirements applicable for the solderability and the resistance to soldering heat test. 1.4.4 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.6 of this sectional specification, shall be specifically stated. 1.5 Terms

41、and definitions For the purposes of this document, the terms and definitions of IEC 60384-1 and the following apply. 1.5.1 Performance grades 1.5.1.1 performance grade 1 capacitors (long-life) capacitors intended for long-life applications with stringent requirements for the electrical parameters 1.

42、5.1.2 performance grade 2 capacitors (general purpose) capacitors for general application where the stringent requirements of performance grade 1 are not necessary 1.5.2 stability grade capacitance drift after climatic and mechanical tests and after endurance tests NOTE The performance grade and the

43、 stability grade shall be noted in the detail specification. 1.5.3 performance grade and stability grade combinations see the table below for preferred values Table 1 Preferred values Performance grades Stability grades Combination designations 1 1.1 1 2 1.2 2 2 The three combinations of performance

44、 grades and stability grades concern capacitance stability and tan values. Distinction in performance of the three combinations is shown in Table 4. 1.5.4 rated voltage maximum d.c. voltage which may be applied continuously to a capacitor at the rated temperature NOTE The sum of the d.c. voltage and

45、 the peak a.c. voltage applied to the capacitor must not exceed the rated voltage. The value of the peak a.c. voltage allowed at different frequencies is under consideration. BS EN 60384-16:2005EN 60384-16:2005 8 1.6 Marking See 2.4 of IEC 60384-1, with the following details: 1.6.1 The information g

46、iven in the marking is normally selected from the following list; the relative importance of each item is indicated by its position in the list: a) rated capacitance; b) rated voltage (d.c. voltage may be indicated by the symbol or );c) tolerance on rated capacitance; d) year and month (or week) of

47、manufacture; e) manufacturers name or trade mark; f) climatic category; g) manufacturers type designation; h) reference to the detail specification. 1.6.2 The capacitor shall be clearly marked with a), b) and c) above and with as many as possible of the remaining items as is considered necessary. An

48、y duplication of information in the marking on the capacitor should be avoided. 1.6.3 The package containing the capacitor(s) shall be clearly marked with all the information listed in 1.6.1. 1.6.4 Any additional marking shall be so applied that no confusion can arise. 2 Preferred ratings and charac

49、teristics 2.1 Preferred characteristics The values given in detail specifications shall preferably be selected from the following: 2.1.1 Preferred climatic categories The capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC 60068-1. The lower and upper category temperatures and the duration of the damp heat, steady state test shall be chosen from the following: Lower category temperature: