EN 60384-16-1-2005 en Fixed capacitors for use in electronic equipment Part 16-1 Blank detail specification Fixed metallized polypropylene film dielectric d c capacitors - Assessme.pdf

《EN 60384-16-1-2005 en Fixed capacitors for use in electronic equipment Part 16-1 Blank detail specification Fixed metallized polypropylene film dielectric d c capacitors - Assessme.pdf》由会员分享，可在线阅读，更多相关《EN 60384-16-1-2005 en Fixed capacitors for use in electronic equipment Part 16-1 Blank detail specification Fixed metallized polypropylene film dielectric d c capacitors - Assessme.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60384-16-1: 2005Fixed capacitors for use in electronic equipment Part 16-1: Blank detail specification: Fixed metallized polypropylene film dielectric d.c. capacitors Assessment levels E and EZICS 31.060.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g

2、53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Incorporating corrigendum March 2010National forewordThis British Standard is the UK implementation of EN 60384-16-1:2005. It is identical to IEC 60384-16-1:2005. It supers

3、edes BS EN 131201:2002 and BS QC 301201:1984 which are withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.T

4、his publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 60384-16-1:2005This British Standard was published under the authority of t

5、he Standards Policy and Strategy Committee on 10 February 2006 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 March 2010 Supersession text amended ISBN 978 0 580 70373 7EUROPEAN STANDARD EN 60384-16-1 NORME EUROPENNE EUROPISCHE NORM December 2005 CENELEC European Committee fo

6、r Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members

7、. Ref. No. EN 60384-16-1:2005 E ICS 31.060.30 Supersedes EN 131201:2002English version Fixed capacitors for use in electronic equipment Part 16-1: Blank detail specification: Fixed metallized polypropylene film dielectric d.c. capacitors - Assessment levels E and EZ (IEC 60384-16-1:2005) Condensateu

8、rs fixes utiliss dans les quipements lectroniques Partie 16-1: Spcification particulire cadre: Condensateurs fixes pour courant continu dilectrique en film de polypropylne mtallis Niveaux dassurances E et EZ (CEI 60384-16-1:2005) Festkondensatoren zur Verwendung in Gerten der Elektronik Teil 16-1: V

9、ordruck fr Bauartspezifikation: Festkondensatoren mit metallisierter Polypropylen-Folie als Dielektrikum fr Gleichspannung - Qualittsbewertungsstufen E und EZ (IEC 60384-16-1:2005) This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to comply with the CEN/CENELEC

10、Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENEL

11、EC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.

12、CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Swed

13、en, Switzerland and United Kingdom. Foreword The text of document 40/1596/FDIS, future edition 2 of IEC 60384-16-1, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-16-1 on 2005-11-01. Thi

14、s European Standard supersedes EN 131201:2002. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-08-01 latest date by which the national standards conflicting with the EN h

15、ave to be withdrawn (dow) 2008-11-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60384-16-1:2005 was approved by CENELEC as a European Standard without any modification. _ EN 60384-16-1:2005 2 BS EN 60384-16-1:2005 3 EN 60384-16-1:2005 FIXED CA

16、PACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 16-1: Blank detail specification: Fixed metallized polypropylene film dielectric d.c. capacitors Assessment levels E and EZ INTRODUCTION Blank detail specification A blank detail specification is a supplementary document to the sectional specification an

17、d contains requirements for style and layout and minimum content of details specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they be so described. In the preparation of detail specifications the

18、 content of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated: Identification of the detail specification 1 The “International Electrotechnical commi

19、ssion“ or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national

20、 Generic Specification. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (when applicable). NOTE When the capacitor is not designed for use in printed board applications, this mus

21、t be clearly stated in the detail specification in this position. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an appendix to the detail spec

22、ification. 8 Application or group of applications covered and/or assessment level. NOTE The assessment level(s) to be used in a detail specification shall be selected from the sectional specification, 3.5.4. This implies that one blank detail specification may be used in combination with several ass

23、essment levels provided the grouping of the tests does not change. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. BS EN 60384-16-1:2005EN 60384-16-1:2005 4 1 IEC 60384-16-1-XXX QC XXXXXXXXXXX 2 IEC 60384-16-1 QC XXXXXX 4 ELECTRONIC COMPONE

24、NTS OF ASSESSED QUALITY IN ACCORDANCE WITH: 3 FIXED METALLIZED POLYPROPYLENE FILM DIELECTRIC DC CAPACITORS 5 6 Outline drawing (see Table 1) (first angle projection) 7 (Other shapes are permitted within the dimensions given) Assessment levels E and EZ 8 Performance grade: Stability grade: NOTE For 1

25、 to 9: see previous page. Information on the availability of components qualified to this detail specification is given in IEC QC 001005 9 1 General data 1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-16, 1.4.2. 1.2 Dimensions Table 1 Case size reference and dimensions Dimensio

26、ns Case size reference L H d . . . . . . . When there is no case size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1. The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteris

27、tics Capacitance range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category Rated temperature Tangent of loss angle Insulation resistance BS EN 60384-16-1:2005 5 EN 60384-16-1:2005 Table 2 Values of capacitance and

28、of voltage related to case sizes Rated voltage Category voltage* Case size Case size Case size Case size Rated capacitance (in nF and/or F) * If different from the rated voltage. 1.4 Normative references The following referenced documents are indispensable for the application of this document. For d

29、ated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60384-16, Fixed capacitors for use in electronic equipment Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d

30、.c. capacitors 11.5 Marking The marking of the capacitor and the packing shall be in accordance with the requirements of IEC 60384-16, 1.6. NOTE The details of the marking of the component and packing must be given in full in the detail specification. 1.6 Ordering information Orders for capacitors c

31、overed by this specification shall contain, in clear or in coded form, the following minimum information: a) rated capacitance; b) tolerance on rated capacitance; c) rated d.c. voltage; d) number and issue reference of the detail specification and style reference; e) performance and stability grade,

32、 if necessary. 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTE Additions or increased requirements shoul

33、d be specified only when essential. Table 3 Other characteristics This table is to be used for defining characteristics which are additional to or more severe than those given in the sectional specification. _ 1To be published. BS EN 60384-16-1:2005EN 60384-16-1:2005 6 2 Inspection requirements 2.1

34、Procedures 2.1.1 For qualification approval, the procedures shall be in accordance with the sectional specification, IEC 60384-16, 3.4. 2.1.2 For quality conformance inspection the test schedule (Table 4) includes sampling, periodicity, severities and requirements. The formation of inspection lots i

35、s covered by 3.5.1 of the sectional specification. Table 4 Test schedule for quality conformance inspection E lev. EZ lev. IL AQL n cSubclause number and testa D or ND cConditions of testa cPerformance requirementsa Group A inspection (lot-by-lot) Subgroup A0 4.2.2 Capacitance 4.2.3 Tangent of loss

36、angle 4.2.1 Voltage proof (Test A) 4.2.4 Insulation resistance (Test A) Frequency : 1 kHz for all capacitance values Method: Measuring point 1a Measuring point 1a 100%dWithin specified tolerance As in 4.2.3.2 No breakdown or flashover. Self-healing breakdowns allowed As in 4.2.4.3 Subgroup A1 ND S-3

37、 2,5%b0 4.1 Visual examination As in 4.1 Legible marking and as specified in 1.5 of this specification 4.1 Dimensions (gauging) As specified in Table 1 of this specification Subgroup A2 ND S-3 1,0%b0 4.2.2 Capacitance Within specified tolerance 4.2.3 Tangent of loss angle As in 4.2.3.2 4.2.1 Voltage

38、 proof (Test A) No breakdown or flashover 4.2.4 Insulation resistance (Test A) As in 4.2.4.2 Group B inspection (lot-by-lot) Subgroup B1 ND S-3 2,5%b0 4.5 Solderability Without ageing Method: . Good tinning as evidenced by free flowing of the solder with wetting of the termina-tions or solder shall

39、flow within . s, as applicable 4.15 Solvent resistance of the marking (if applicable) Solvent: . Solvent temperature: . Method 1 Rubbing material: . Recovery time: Legible marking BS EN 60384-16-1:2005 7 EN 60384-16-1:2005 Table 4 (continued) Subclause number and testaD or NDcConditions of testa Sam

40、ple size and criterion of acceptability cPerformance requirementsaE EZ p n c p n c Group C inspection (periodic) Subgroup C1A Part of sample of Subgroup C1 D 6 9 1 6 5 0 4.1 Dimensions (detail) See detail specification 4.3.1 Initial measurements Capacitance Tangent of loss angle: for CR 1 F: at 1 kH

41、z CR 1 F: at 10 kHz 4.3 Robustness of terminationsVisual examination No visible damage 4.4 Resistance to soldering heat Method: 4.14 Component solvent resistance (if applicable) Solvent: . Solvent temperature: . Method 2 Recovery time: See detail specification 4.4.2 Final measurements Visual examina

42、tion No visible damage Legible marking Capacitance C/C for Grade 1.1: 1 %Grade 1.2: 2 % Grade 2: 3 % of value measured in 4.3.1 Tangent of loss angle Increase of tan : for C 1 F: for Grade 1.1: 0,001 Grade 1.2: 0,002 Grade 2: 0,004for C 1 F: see detail specification, compared to values measured in 4

43、.3.1 Subgroup C1B Other part of sample of Subgroup C1 D 6 18 1 6 5 0 4.6.1 Initial measurements Capacitance Tangent of loss angle: for CR 1 F: at 1 kHz CR 1 F: at 10 kHz 4.6 Rapid change of temperature TA= Lower category temperature TB= Upper category temperature Five cycles Duration t = 30 min Visu

44、al examination No visible damage 4.7 Vibration Frequency range: . Hz to . Hz Amplitude 0,75 mm or acceleration 100 m/s2(whichever is the less severe) Total duration: 6 h BS EN 60384-16-1:2005EN 60384-16-1:2005 8 Table 4 (continued) Subclause number and testaD or NDcConditions of testa Sample size an

45、d criterion of acceptability cPerformance requirementsaE EZ p n c p n c 4.7.2 Final inspection Visual examination No visible damage 4.8 Bump (or shock, see 4.9) Method of mounting: see 1.1 of this specification Number of bumps: . Acceleration: m/s2Duration of pulse: . ms 4.9 Shock (or bump, see 4.8)

46、 Method of mounting: see 1.1 of this specification Acceleration: m/s2Duration of pulse: . ms 4.8.3 or 4.9.3 Final measurements Visual examination No visible damage Capacitance C/C for Grade 1.1: 1 % Grade 1.2: 2 % Grade 2: 3 % of value measured in 4.6.1 Tangent of loss angle Increase of tan : for C

47、1 F: for Grade 1.1: 0,001Grade 1.2: 0,002Grade 2: 0,004for C 1 F: see detail specification, compared to values measured in 4.6.1 Insulation resistance 50 % of the values in 4.2.4.2 Subgroup C1 Combined sample of specimens of Subgroups C1A and C1B D 6 27 2 6 10 0 4.10 Climatic sequence 4.10.2 Dry hea

48、t Temperature: upper category temperature Duration: 16 h 4.10.3 Damp heat, cyclic, Test Db, first cycle 4.10.4 Cold Temperature: lower category temperature Duration: 2 h 4.10.5 Low air pressure (if required by the detail specification) Air pressure: 8 kPa 4.10.5.3 Final measurement Visual examinatio

49、n No permanent breakdown, flashover or harmful deformation of the case 4.10.6 Damp heat, cyclic, Test Db, remaining cycles BS EN 60384-16-1:2005 9 EN 60384-16-1:2005 Table 4 (continued) Subclause number and testaDorNDcConditions of testa Sample size and criterion of acceptability cPerformance requirementsaE EZ p n c p n c 4.10.6.2 Final measurem