EN 60371-3-7-1995 en Insulating materials based on mica Part 3 Specifications for individual materials Sheet 7 Polyester film mica paper with an epoxy resin binder for single condu.pdf

《EN 60371-3-7-1995 en Insulating materials based on mica Part 3 Specifications for individual materials Sheet 7 Polyester film mica paper with an epoxy resin binder for single condu.pdf》由会员分享，可在线阅读，更多相关《EN 60371-3-7-1995 en Insulating materials based on mica Part 3 Specifications for individual materials Sheet 7 Polyester film mica paper with an epoxy resin binder for single condu.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BRITISH STANDARDBS EN 60371-3-7: 1996IEC 371-3-7: 1995Incorporating amendment no. 1Specification for

2、Insulating materials based on mica Part 3: Specifications for individual materials Sheet 7: Polyester film mica paper with an epoxy resin binder for single conductor tapingThe European Standard EN 60371-3-7:1995, incorporating amendment A1:2006, has the status of a British StandardICS 29.040.20BS EN

3、 60371-3-7:1996This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1996 BSI 2007The following BSI references relate to the work on this standard:Committee refe

4、rence GEL/15Draft for comment 94/216462 DCISBN 0 580 25264 7Committees responsible for this British StandardThe preparation of this British Standard was entrusted to Technical Committee GEL/15, Insulating materials, upon which the following bodies were represented:British Ceramic Research Ltd.Britis

5、h Industrial Ceramic Manufacturers AssociationBritish Telecommunications plcDepartment of Trade and Industry (National Physical Laboratory)Electrical and Electronic Insulation Association (BEAMA Ltd.)Electricity AssociationFederation of the Electronics IndustryMinistry of DefenceRotating Electrical

6、Machines Association (BEAMA Ltd.)Transmission and Distribution Association (BEAMA Ltd.)The following bodies were also represented in the drafting of the standard, through subcommittees and panels:ERA Technology Ltd.Mica Trade ClubAmendments issued since publicationAmd. No. Date Comments16939 28 Febr

7、uary 2007 See national forewordBS EN 60371-3-7:1996 BSI 2007 iContentsPageCommittees responsible Inside front coverNational foreword iiForeword 2Introduction 31Scope 32 Normative references 33 Designation 34 Requirements: raw materials 35 Requirements: composition and tolerances 36 Requirements of m

8、aterial (as received) 47 Requirements of material after cutting 58 Packing 5Annex ZA (normative) Normative references to international publications with their corresponding European publications 6Table 1 Composition 4Table 2 Tolerance on width 4List of references Inside back coverBS EN 60371-3-7:199

9、6ii BSI 2007National forewordThis British Standard was published by BSI. It is the UK implementation of EN 60371-3-7:1995, incorporating amendment A1:2006. It is identical with IEC 60371-3-7:1995, incorporating amendment 1:2006 and corrigendum August 1995.The start and finish of text introduced or a

10、ltered by amendment is indicated in the text by tags !“. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is indicated by !“.This publication does not purport to include all the necessary provisions of a contract. Users are respo

11、nsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 60371-3-7September 1995+A1November 2006ICS 29.040.20Descriptors: Electrical insulating materials, solid electrical insulating material

12、s, electrical insulating paper, micaceous products, polyester resins, epoxy resins, designation, specifications, composition, compositional tolerances, dimensions, packingEnglish versionInsulating materials based on micaPart 3: Specifications for individual materialsSheet 7: Polyester film mica pape

13、r with an epoxy resin binder for single conductor tapingMatriaux isolants base de micaPartie 3: Spcifications pour matriaux particuliersFeuille 7: Ruban base de papier de mica, film polyester et liant poxyde pour lisolation de conducteurs lmentairesGlimmererzeugnisse fr elektrotechnische ZweckeTeil

14、3: Bestimmungen fr einzelne MaterialienBlatt 7: Polyesterfolienverstrktes Glimmerpapier mit einem Epoxidharz-Bindemittel zur EinzelleiterbandelungThis European Standard was approved by CENELEC on 1995-07-04. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulat

15、e the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.This European Standard exi

16、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national elect

17、rotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENELECEuropean Committee for Electrotechnical StandardizationComit Europen de Normalisation Electr

18、otechniqueEuropisches Komitee fr Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B-1050 Brussels 1995 Copyright reserved to CENELEC membersRef. No. EN 60371-3-7:1995 EEN 60371-3-7:1995 BSI 20072ForewordThe text of document 15C/477/DIS, future edition 1 of IEC 371-3-7, prepared by S

19、C 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC with its corrigendum August 1995 as EN 60371-3-7 on 1995-07-04.The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In

20、 this standard, Annex ZA is normative. Annex ZA has been added by CENELEC.Foreword to amendment 1The text of document 15/334/FDIS, future amendment 1 to IEC 60371-3-7:1992, prepared by IEC TC 15, Standards on specifications for electrical insulating materials, was submitted to the IEC-CENELEC parall

21、el vote and was approved by CENELEC as amendment A1 to EN 60371-3-7:1995 on 2006-10-01.The following dates were fixed: Endorsement noticeThe text of amendment 1:2006 to the International Standard IEC 60371-3-7:1992 was approved by CENELEC as an amendment to the European Standard without any modifica

22、tion. latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1996-08-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dop) 1996-08-01 latest date by which the amendment h

23、as to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-07-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2009-10-01EN 60371-3-7:1995 BSI 2007 3Introduction!This International Stand

24、ard is one of a series which deals with insulating materials for use in electrical equipment built up from mica splittings or mica paper, with or without reinforcement, and with mica paper in its pure state.The series consists of the following three parts: Part 1: Definitions and general requirement

25、s (IEC 60371-1); Part 2: Methods of test (IEC 60371-2); Part 3: Specifications for individual materials (IEC 60371-3). This standard contains one of the sheets comprising part 3, as follows: Sheet 7: Polyester film mica paper with an epoxy resin binder for single conductor taping.“1 ScopeThis Intern

26、ational Standard specifies the requirements for an electrical insulating material containing mica paper with polyester film and with an epoxy resin binder for single conductor taping. The material is supplied in a flexible state with the resin in the B-stage for final cure after application. It is s

27、upplied in roll form. This specification refers only to single film, although compositions with polyester film facings of various thicknesses are available. The specification covers material having a nominal thickness from 0,07 mm to 0,12 mm.Materials which conform to this specification meet establi

28、shed levels of performance. However, the selection of a material for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.!Safety warning:It is the responsibility of the user of the methods

29、contained or referred to in this document to ensure that they are used in a safe manner.“2 Normative referencesThe following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions in

30、dicated were valid. All normative documents are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and ISO maintain registers

31、 of currently valid International Standards.!IEC 60243-1:1998, Electric strength of insulating materials Test methods Part 1: Tests at power frequencies. IEC 60371-2:2004, Specification for insulating materials based on mica Part 2: Methods of test. IEC 60371-3-2:2005, Insulating materials based on

32、mica Part 3: Specifications for individual materials Sheet 2: Mica paper. IEC 60674-3-2:1992, Specification for plastic films for electrical purposes Part 3: Specifications for individual materials Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for

33、electrical insulation“. 3 Designation!When ordering materials to this specification, only the specification and type numbers need be quoted (see Table 1).Example: IEC 60371-3-7: type 7.1.01The type number is derived from: Thus giving type number 7.1.01.“The descriptive code quoted in Table 1, e.g. F

34、23/M50/R14 for type 7.1.01, Table 1, is derived from: film thickness (F) 23 4m muscovite mica content (M) 50 g/m2 resin content (R) 14 g/m2.4 Requirements: raw materials4.1 Mica paper!Mica paper referred to in this specification shall comply with the requirements of IEC 60371-3-2.“4.2 Polyester film

35、!Plastic films used as backing material shall be made from PET and shall comply with the requirements of IEC 60674-3-2.“4.3 Epoxy resinAny epoxy resin system may be used which enables the material to meet the requirements of this specification.5 Requirements: composition and tolerances!When tested b

36、y the method of Clause 7 of IEC 60371-2, the composition of the products shall lie within the limits given in Table 1.“ the specification sheet number 7 followed by the sheet table number 1 followed by the number of the product in the sheet table01.EN 60371-3-7:19954 BSI 2007Table 1 Composition6 Req

37、uirements of material (as received)6.1 GeneralAll materials in any one consignment shall have the same properties, within the limits of this specification, throughout the length of each roll.The surfaces shall be uniform and free from defects such as bubbles, pin-holes, creases and flaws.The roll sh

38、all be capable of being unrolled continuously without damage, and the force required to unroll the material shall be substantially uniform.To prevent damage to the mica paper component during winding, the unwinding tension shall be less than 75 % of the minimum allowable tensile strength.Unless othe

39、rwise specified in the purchase contract, the material shall be rolled with the mica surface on the outside.6.2 WidthThis specification contains no requirements for widths of tape. However, the following widths are preferred: 6 mm, 8 mm, 10 mm, 12 mm, 15 mm and 20 mm.The tolerance on the width of th

40、e material shall be as in Table 2. The maximum trimmed width of full width material and sheet normally available is 1 000 mm. Table 2 Tolerance on width6.3 Thickness!Measure the thickness in accordance with Clause 4 of IEC 60371-2, using the apparatus given in 4.1.1 of that standard, making 10 measu

41、rements of one thickness of material.“ The measured values shall be in accordance with the requirements given in Table 1.6.4 LengthThere are no requirements in this specification for roll length, and these should therefore be subject to the purchase contract.6.5 CoresThe tape shall be compactly woun

42、d on cores of 55 mm or 76 mm interior diameter which shall be free of sharp edges. The width of the cores should be subject to the purchase contract.6.6 JoinsThe number of rolls with joins shall be limited to 25 % of any one consignment. Rolls of length less than 100 m shall contain no more than one

43、 join.For rolls of length more than or equal to 100 m, the number of joins should be subject to the purchase contract. Method of making the joins should be subject to the purchase contract.6.7 StiffnessThe stiffness of the material should be subject to the purchase contract. !When the stiffness is s

44、pecified, the material should be tested by the method of Clause 11 in IEC 60371-2.“6.8 Electric strength!When tested by the method of Clause 16 of IEC 60371-2 with electrodes according to 4.1.2 of IEC 60243-1, the electric strength shall be not less than 50 kV/mm.“6.9 Tensile strength!When tested by

45、 the method of Clause 8 of IEC 60371-2, the tensile strength shall be not less than 25 N/10 mm width for 23 4m film and 40 N/10 mm width for 30 4m film.“TypeDescriptive codePET film substanceg/m2Mica contentg/m2Resin contentg/m2Mass/unit areag/m2Permissiblethickness rangemmVolatile contentNom. Tol.N

46、om. Tol.Nom. Tol.Nom. Tol.Mean Individual Max. %7.1.017.1.027.1.037.1.047.1.057.1.06F23/M50/R14F23/P63/R16F23/M75/R18F30/M75/R12F23/P80/R19F30/P80/R13323232433243333434506375758080556677141618121913345353961111251301311361011121313140,060,070,070,080,090,100,090,100,100,110,100,110,050,080,060,090,0

47、80,110,080,110,090,120,090,121,01,01,01,01,01,0Nominal widthmmTolerancemmk 20 20 k 500 500 0,5 1,0 5,0EN 60371-3-7:1995 BSI 2007 57 Requirements of material after curingRequirements of material after curing shall be subject to the purchase contract.8 PackingThe materials should be packaged to ensure

48、 adequate protection during transport, handling and storage. Any necessary packing requirements should be subject to the purchase contract.Each package containing a number of unit packs shall have the following information, clearly and indelibly marked on it:a) description of the material and the nu

49、mber of this specification;b) the width of the material and the length per roll;c) the number of rolls;d) the date of manufacture;e) shelf-life and storage conditions.The manufacturers reference number and batch number shall be identified on each package or roll.Rolls with joins shall be packed together and clearly labelled on the outside of the container.EN 60371-3-7:19956 BSI 2007Annex ZA!(normative) Normative references to international publications with their corresponding European publicationsThe follo