EN 60297-3-101-2004 en Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482 6 mm (19 in) series Part 3-101 Subracks and associated plug-i.pdf

《EN 60297-3-101-2004 en Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482 6 mm (19 in) series Part 3-101 Subracks and associated plug-i.pdf》由会员分享，可在线阅读，更多相关《EN 60297-3-101-2004 en Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482 6 mm (19 in) series Part 3-101 Subracks and associated plug-i.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60297-3-101: 2004Incorporating corrigendum May 2008Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 3-101: Subracks and associated plug-in unitsICS 31.240g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3

2、g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60297-3-101:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 18 January 2005 BSI 2008IS

3、BN 978 0 580 62595 4National forewordThis British Standard is the UK implementation of EN 60297-3-101:2004. It is identical with IEC 60297-3-101:2004. It supersedes BS 5954-3:1985, BS EN 60297-5-100:2001, BS EN 60297-5-102:2001, BS EN 60297-5-103:2001 and BS EN 60297-5-107:2001 which are withdrawn.

4、Together with BS EN 60297-3-102, supersedes BS EN 60297-4:1995, which is now withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/48/4, Mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained on reques

5、t to its secretary.This publication does not purport to include all the necessary provisions of a contract.Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate Comments30

6、May 2008 Addition of supersession details in national forewordEUROPEAN STANDARD EN 60297-3-101NORME EUROPENNE EUROPISCHE NORM September 2004CENELEC European Committee forElectrotechnicalStandardizationComit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische Normung Cen

7、tral Secretariat:rue de Stassart35, B - 1050 Brussels 2004 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELECmembers.Ref. No. EN 60297-3-101:2004 EICS 31.240 Supersedes HD 493.3 S2:1993,EN 60297-4:1995 + A1:1999, EN 60297-5-100:2001,EN 60297-5-102:2001, E

8、N 60297-5-103:2001 &EN 60297-5-107:2001English version Mechanical structures for electronic equipment -Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 3-101: Subracks and associated plug-in units (IEC 60297-3-101:2004)Structures mcaniquespour quipement lectronique -Dimensions

9、 des structures mcaniquesde la srie de 482,6 mm (19 in)Partie 3-101: Bacs et blocs enfichablesassocis (CEI 60297-3-101:2004)Bauweisen fr elektronische Einrichtungen -Mae der 482,6-mm-(19-in-)Bauweise Teil 3-101: Baugruppentrgerund Baugruppen (IEC 60297-3-101:2004)This European Standard was approved

10、by CENELEC on 2004-09-01. CENELEC membersare bound tocomply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national sta

11、ndards may be obtained onapplication to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the responsibility of aCENELEC member into its own language andnotifi

12、ed to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committeesofAustria, Belgium,Cyprus, CzechRepublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta

13、, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Foreword The text of document 48D/299/FDIS, future edition 1 of IEC 60297-3-101, prepared bySC 48D,Mechanical structures for electronic equipment, of IEC TC 48, Electromechanical components an

14、d mechanical structures for elec tronic equipment, was submitted to the IEC-C ENELEC parallel vote and was approved by CENELEC as EN 60297-3-1 01 on 2004-09-01. This European Standard supersedes HD 493.3 S2:1993, EN 60297-4:1995 + A1:1999,EN 60297-5-100:2001, EN 60297-5-102:2001 + corrigendum July 2

15、001, EN 60297-5-103:2001 andEN 60297-5-107:2001. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-06-01 latestdate by which the national standards conflictingwith the EN h

16、ave to be withdrawn (dow) 2007-09-01 Annex ZA has been added by CENELEC. _ Endorsement noticeThe text of the International Standard IEC 60297-3-101:2004 was approved by CENELE C as aEuropean Standard without any modification. _ Page 2BS EN 60297-3-101:2004CONTENTSINTRODUCTION.41Scope and object52Nor

17、mative references.53Terms and definitions.64Arrangement overview65Subrack dimensions, front moun ting area.76Subrack dimensions, rear mounting area107Printed board typeplug-in units,front mounted.128Box type plug-in units, front mounted .149Printed board typeplug-in units,rear mounted.1610 Subrack a

18、nd plug-in unitswith electromagnetic shielding provisions.1711 Plug-in units electrostatic discharge provisions.1912 Dimensions usedin the figures.21 AnnexZA (normative) Normative references to internationalpublications with theircorresponding European publications.22Figure 1 Relationship between th

19、e new IEC 60297-3 series and the old IEC 60297 series.4Figure 2 Arrangement overview.6Figure 3 Subrack dimensions, front mounting area Part 1.7Figure 4 Subrack dimensions, front mounting ar ea Part 2 .8Figure 5 Subrack dimensions, front mounting area Part 3.9Figure 6 Subrack dimensions, rear mountin

20、garea.10Figure 7 Printed board type plug-in unit, 3U.12Figure 8 Printed board type plug-in unit, 6U.13Figure 9 Printed board type plug-in unit, 9U.13Figure 10 Box typeplug-in unit, 3U14Figure 11 Box typeplug-in unit, 6U15Figure 12 Box typeplug-in unit, 9U15Figure 13 Printed board type plug-in units,

21、 rearmounting dimensions16Figure 14 Subrack shielding interface dimensions17Figure 15 Plug-in unit andfiller panels shielding interface dimensions.18Figure 16 ESD contact interface dimensions19Figure 17 ESD strip interface dimensions 19Table 1 RD1 dimensions11Table 2 Depth dimensions RD3, RD4.16Tabl

22、e3Heightdimensions.2 0Table4Depth dimensions. .2 0Page 3BS EN 60297-3-101:2004INTRODUCTION The “Dimensions of mechanical structures of the 482,6mm (19 in) standards are defined inIEC60297.Tothe original IEC 60297-3:1988 publication wa s added Amendment 1:1995. The additional requirements were publis

23、hed inIEC 60297-4:1995 with A mendment 1:1999.The extended requirements were published in the IEC 60297-5-1XX series (2001).Responding to market requirements and for more clar ityitbecame necessary t o merge andtechnically enhance these standard “parts”into3 “new” standards for subracks andassociate

24、d plug-in units. This “merged”standard series now defined as IEC 60297-3-101,IEC60297-3-102 and IEC 60297-3-103 explains its relationship tothe previous “fragmented”IEC60297-X standards, see Figure 1.The nomenclature ofthese new standards has beenrevised. The relationship to IEC 60297-1(Part 1: Pane

25、lsand Racks) has been maintained. The relationship to IEC 60297-2 (Part 2:Cabinets and pitches of rack structures) hasbeen maintained. The relationship to IEC 61587-1(Part 1: Climatic, mechanical tests and safety aspects for cabinets, racks, subracks andchassis) and IEC TS 61587-3 (Part 3: Electroma

26、gnetic shielding performance tests forcabinets, racks and subracks) has been added.The IEC60297-3-101 standard defines the interfaces ofthe basic 482,6 mm (19 in) subrackand associated plug-in units.Figure 1 Relationship between the newIEC 60297-3 series and the old IEC 60297 seriesSubracks and plug

27、-in unitsIEC 60297-3-101 New“merged” standard seriesSubracks and associated plug-in units Subracks and plug-in units:Injector/extractor handle IEC 60297-3-102 Subracks and plug-in units:Keying and alignment pinIEC 60297-3-103 IEC 60297-3 IEC 60297-4 IEC 60297-5-102 IEC 60297-5-103 IEC 60297-5-107 Ol

28、d“fragmented“ standard seriesSubracks and associatedplug-in units IEC 60297-5-101 IEC 60297-4IEC 60297-5-104 IEC 60297-5-105 IEC 1089/04Page 4BS EN 60297-3-101:2004MECHANICAL STRUCTURESFOR ELECTRONIC EQUIPMENT DIMENSIONS OF MECHANICAL STRUCTURES OF THE482,6 mm (19 in) SERIES Part 3-101: Subracks and

29、 associated plug-in units1 Scope and objectThis part of IEC 60297 c overs the basic dimensional relationship of a modular range ofsubracks and associated plug -in units in compliance w ith the IEC 60297 series.The purpose of thisstandard is to specify dimensions which will ensure dimensionalintercha

30、ngeabilityof subracks and associated plug-inunits.Connector related dimensions are limited to “inspection dimensions”only.For mechanicaland climatic tests referto IEC61587-1.For electromagneticshielding performance tests, refer to IEC 61587-3. 2 Normative referencesThe following referenced documents

31、 are indispensable for the application of this document.Fordated references,onlythe edition cited applies. For undated references, the latest editionof the referenced document(including any amendments) applies.IEC 60249-2-1, Base materials for printedcircuits Part 2: Specifications. Specification No

32、. 1:Phenolic cellulose paper copper-clad laminated sheet,highelectricalqualityIEC 60297-1:1986, Dimensions of mechanical structures of the 482,6 mm (19 in) seriesPart 1:Panels and racksIEC 60297-2:1982, Dimensions of mechanical structures of the 482,6 mm (19 in) seriesPart 2: Cabinets and pitches of

33、rackstructuresIEC 60603-2:1995, Connectors forfrequencies below 3 MHz for use wi th printed boards Part 2: Detail specification for two-part co nnectors with assessed quality, for printed boards,for basic grid of 2,54 mm (0,1 in) withcommon mountingfeaturesIEC 60917-1:1998, Modular order for thedeve

34、lopment of mechanical structures for electronicequipment practices Part 1: Generic standardIEC 61076-4-101:2001, Connectors for electronic equipment Part4-101: Printed boardconnectorswithassessed quality Detail specification fortwo-part connector modules,havi nga basic grid of 2,0 mm forprinted boar

35、ds and backplanes in accordance with IEC 60917 IEC 61076-4-113:2002, Connectors for electronic equipment Printed board connectors Part 4-113: Detail specification fortwo-part connectors having5 rows with a grid of 2,54 mmforprinted boardsand backplanes in bus applicationsIEC 61587-1:1999, Mechanical

36、 structures for electronic equipment Tests for IEC 60917and IEC60297 Part 1: Climatic, mechanical tests and safety aspects for cabinets,racks, subracks and chassisPage 5BS EN 60297-3-101:2004IEC 61587-3:1999, Mechanical structures for electronic equipment Tests for IEC 60917and IEC60297 Part 3: Elec

37、trom agnetic shielding performance tes ts for cabinets, racks and subracks 3 Terms and definitionsFor the purposesof this part of IEC 60297, the terms and definitions given in IEC 60917-1apply.4 Arrangement overviewThearrangement overview shown in Figure2illustrates a typical 6U subrack with subdivi

38、sionsand rear mounted plug-in units.Abbreviation: 1U = 44,45 mm (see Table 3). Optional features:Subrack and plug-in units electromagnetic shielding provisions (see Clause 10). Plug-in unitselectrostatic discharge provisions (see Clause 11).Figure 2 ArrangementoverviewTypical subrack 6Uwith subdivis

39、ion2 x 3U + 1 x 6U Front mounted box typeplug-in unit6URear mounted box typeplug-in unit6UFront mounted printed board typeplug-in unit3UIEC 1090/04Page 6BS EN 60297-3-101:20045 Subrack dimensions, front mounting area The front mounting area of a subrack defines the aperture dimensions for plug-in un

40、its, theguide rail positions, the mounting dimensions to the cabinet and the depth dimensions with therelevant connectors, as shown in Figures 3 to 5.Dimensions inmillimetresFigure 3 Subrack dimensions, front mounting area Part 1H7U 5,08First pitchline Section A-A 482, 6 0,4 B BA A 426,72“Y“ (see Fi

41、gure 4)Mounting points on front and rear M2, 52 ,54 84 x“X“(see Figure 5)Front viewA 449 (including fixing hardware) Sideplate may exceed D1 (e.g.for protection ofconnectors) Backplane attachmentplaneFrontattachmentplane D1 Typical guiderail 2,54 0,6 AH5 H6 H1 83 x 5,08IEC 1091/04Page 7BS EN 60297-3

42、-101:2004Dimensions inmillimetresFigure 4 Subrack dimensions, front mounting area Part 2Heightseparation plane 11,6 Optional connector/backplane mounting supportSection B-B of multip le heig ht subrack ( 6U, 9U )Heightseparation plane D1Back-plane ConnectorD2 “Z“ (See Figure 5)Frontattachmentplane A

43、ttachmentplane for connector fixing parts A ttachmentplane for backplanesSection BB of single height subrack (3U)n 44,4510,850,1H6 H6 3,6 2)H7 2,54 H6 2,54 H2 H4H3261,5+0,30 6,8 +0,50 6,8 +0,50 IEC 1093/04Page 9BS EN 60297-3-101:2004Typical guiderail, frontTypical guiderail, rear6 Subrack dimensions

44、, rear mounting area The rear mounting area of a subrack defines the aperture dimensions for rear plug-in units, theguide rail positions andthe depth dimensions with the relevant connectors (see Table 1andFigure 6). Dimensions inmillimetres1) RD4: see Clause 9.Figure 6 Subrack dimensions, rear mount

45、ing areaSection C-C First pitchline Rear viewC C VRDetail VR10,164,07 Pitchline Rear mounted guide raildimensions are mirrored as to detail Y in Figure 5 Typical backplane Rearattachmentplane Backplane attachment plane Frontattachment plane D1 RD16 max.Rear connector(shroud) Front connector tail RD4

46、 1)Frontconnector IEC 1094/04Page 10BS EN 60297-3-101:2004Table 1 RD1 dimensionsDimensions inmillimetresPrinted board depth reference (D3) 60 80 100 120 140 160 220 280 Subrack TypeA 1)RD1 0,25 82,48 102,48 122,48 142,48 162,48 182,48 242,48 302,48 Subrack Type B 2)RD1 0,25 80 100 120 140 160 180 24

47、0 300 RD1: Depth inspection dimensions using connectors1) IEC 60603-2 and 61076-4-113.2) IEC 61076-4-101.Page 11BS EN 60297-3-101:20047 Printed board type plug-in units, front mounted The dimensions of front panels, printedboards and fixing parts will insure the compatibility offront mounted plug-in

48、 units into subracks (see Figures 7 to 9). Dimensions inmillimetresFigure 7 Printed board typeplug-in unit, 3U 7,5 3,06 (n 5,08) 0,3 Front attachmentplane First printed board positionPitchline 4,073,92 0,1 8,43 n 5,08 0,2Multipleboard position Section C-C Detail V 8,8 3,6 2,7M2,52,5 2,54 6 D3 3,8V 6

49、,1 0,15 3,43 CCReserved area forboard mounting Pitchline7,62 n 5,08 0,15 n 7,47 H9Connector areaClearance for guide railSide viewFront view3,1 0,1D4 5,0888,90,12,510,16 H104,0722 Printed board Connector area D3Cut out forintermediate horizontal member of the subrackSide viewMissing dimensionsSee Figure 10 +3,50 22 Side viewMissing dimensionsSee Figure 10 D3 +3,5 0 22 3 44,45=133,35IEC 1099/04IEC 1100/04Pag