EN 60297-3-100-2009 en Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482 6 mm (19 in) series - Part 3-100 Basic dimensions of front pa.pdf

《EN 60297-3-100-2009 en Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482 6 mm (19 in) series - Part 3-100 Basic dimensions of front pa.pdf》由会员分享，可在线阅读，更多相关《EN 60297-3-100-2009 en Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482 6 mm (19 in) series - Part 3-100 Basic dimensions of front pa.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinetsBS EN 60297-3-100: 2009raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED

2、 BY COPYRIGHT LAWBSI British StandardsNational forewordThis British Standard is the UK implementation of EN 60297-3-100:2009. It isidentical to IEC 60297-3-100:2008. It supersedes BS 5954-2:1985 which iswithdrawn.The UK participation in its preparation was entrusted to Technical CommitteeEPL/48, Ele

3、ctromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct

4、application. BSI 2009ISBN 978 0 580 58405 3ICS 31.240Compliance with a British Standard cannot confer immunity fromlegal obligations.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60297-3-100:2009This British Standard was published under the authority of the Stan

5、dardsPolicy and Strategy Committee on February 2009.2 8EUROPEAN STANDARD EN 60297-3-100 NORME EUROPENNE EUROPISCHE NORM January 2009 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Centra

6、l Secretariat: avenue Marnix 17, B - 1000 Brussels 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60297-3-100:2009 E ICS 31.240 Supersedes HD 493.1 S1:1988 and HD 493.2 S1:1988English version Mechanical structures for electr

7、onic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets (IEC 60297-3-100:2008) Structures mcaniques pour quipements lectroniques - Dimensions des structures mcaniques de la srie 482,6 mm

8、 (19 pouces) - Partie 3-100: Dimensions de base des panneaux avant, des bacs, des chssis, des btis et des baies (CEI 60297-3-100:2008) Bauweisen fr elektronische Einrichtungen - Mae der 482,6-mm-(19-Zoll-)Bauweise - Teil 3-100: Hauptmae von Frontplatten, Baugruppentrgern, Einschben, Gestellen und Sc

9、hrnken (IEC 60297-3-100:2008) This European Standard was approved by CENELEC on 2008-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-d

10、ate lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation unde

11、r the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Fran

12、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 60297-3-100:2009EN 60297-3-100:2009 - 2 - Foreword The text of document 48D/38

13、0/FDIS, future edition 1 of IEC 60297-3-100, prepared by SC 48D, Mechanical structures for electronic equipment, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60297-3-100

14、 on 2008-12-01. This European Standard supersedes HD 493.1 S1:1988 and HD 493.2 S1:1988. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-09-01 latest date by which the na

15、tional standards conflicting with the EN have to be withdrawn (dow) 2011-12-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60297-3-100:2008 was approved by CENELEC as a European Standard without any modification. In the official version, for Bi

16、bliography, the following note has to be added for the standard indicated: IEC 60917-2-1 NOTE Harmonized as EN 60917-2-1:1995 (not modified). _ BS EN 60297-3-100:2009- 3 - EN 60297-3-100:2009 Annex ZA (normative) Normative references to international publications with their corresponding European pu

17、blications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication

18、 has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60050-581 -1)International Electrotechnical Vocabulary - Part 581: Electromechanical components for electronic equipment - - IEC 60297-3-101 -1)Mechanical structures for

19、electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units EN 60297-3-101 20042)IEC 60917-1 -1)Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard E

20、N 60917-1 19982)- - Equipment Engineering (EE) - European telecommunication standard for equipment practice - Part 3: Engineering requirements for miscellaneous racks and cabinets ETSI EN 300119-3 -1)1)Undated reference. 2)Valid edition at date of issue. BS EN 60297-3-100:2009 2 60297-3-100 IEC:2008

21、 CONTENTS INTRODUCTION.5 1 Scope.6 2 Normative references .6 3 Terms and definitions .6 4 Arrangement overview6 5 Front panels .8 5.1 Front panel dimensions .8 5.2 Front panel mounting hole positions. .10 6 Racks.11 6.1 Rack description11 6.2 Rack/cabinet mounting grid types I and II 12 7 Cabinet 13

22、 7.1 Cabinet description .13 7.2 Dimensions of cabinets type A 13 7.3 Dimensions of cabinets type B 14 Bibliography15 Figure 1 Arrangement overview .7 Figure 2 Front panel dimensions for 1U up to 6U .8 Figure 3 Front panel dimensions for 6U up to 12U .9 Figure 4 Front panel mounting hole positions.1

23、0 Figure 5 Array of racks 11 Figure 6 Rack/cabinet mounting grid12 Figure 7 Dimensions of cabinet type A .13 Figure 8 Dimensions of cabinet type B .14 Table 1 Front panel dimensions for 1U up to 6U 8 Table 2 Front panel dimensions for 6U up to 12U.9 Table 3 Width dimension of fixed rack structures .

24、11 Table 4 Dimensions of cabinet types A and B 14 BS EN 60297-3-100:200960297-3-100 IEC:2008 5 INTRODUCTION This part of IEC 60297 has been developed by merging IEC 60297-1 and IEC 60297-2 into one document. Both parts are reworked in order to meet the latest market requirements of the electronics i

25、ndustry. The purpose is also to create an updated documentation and to improve the drawings and descriptions of the contents. Some parts of this standard contain dimensions of IEC 60917-2-1 and ETSI EN 300119. The merge of the two parts into one updates the scope and improves the overview of the mod

26、ular order, describing the relationship between front panels, subracks, chassis, racks and cabinets. BS EN 60297-3-100:2009 6 60297-3-100 IEC:2008 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 mm (19 in) SERIES Part 3-100: Basic dimensions of front p

27、anels, subracks, chassis, racks and cabinets 1 Scope This part of IEC 60297 specifies the basic dimensions of front panels, subracks, chassis, racks and cabinets of the 482,6 mm (19 in) series. Subsequent standards of the associated IEC 60297-3 series provides detail dimensions for specific parts of

28、 the equipment practice, where the basic dimensions are used as interface to other associated parts. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the lat

29、est edition of the referenced document (including any amendments) applies. IEC 60050-581, International Electrotechnical Vocabulary Chapter 581: Electromechanical components for electronic equipment IEC 60297-3-101, Mechanical structures for electronic equipment Dimensions of mechanical structures o

30、f the 482,6 mm (19 in) series Part 3-101: Subracks and associated plug-in units IEC 60917-1, Modular order for the development of mechanical structures for electronic equipment practices Part 1: Generic standard ETSI EN 300119-3, Equipment engineering (EE)-European telecommunication standard for equ

31、ipment practice Part 3: Engineering requirements for miscellaneous racks and cabinets 3 Terms and definitions For the purposes of this document, the terms and definitions of IEC 60917-1 and IEC 60050-581 apply, as well as the following. 3.1 plinth/base additional structure or an integrated structure

32、 of the cabinet/rack to be used for transport, cable feed, (seismic) anchoring, or provide a safety or convenience distance to the floor level 3.2 vertical member structural part of a rack/cabinet providing mounting holes for front panels, chassis and subracks 4 Arrangement overview Figure 1 illustr

33、ates the relationship of front panels, subracks, chassis, racks and cabinets. The cabinet is usually assembled with vertical members which are the mounting parts for the BS EN 60297-3-100:200960297-3-100 IEC:2008 7 assembly of front panels, subracks and chassis. Racks as defined in IEC 60917-1 are o

34、pen structures of pairs of vertical members without any covers (see 6.1). Typical cabinet with front door and vertical members with mounting holes,corresponding to the front panel, subrack and chassis mounting holes Chassis Front panel Plinth/base Vertical member Subrack Plug-in units associated to

35、the subrack IEC 2056/08 Figure 1 Arrangement overview BS EN 60297-3-100:2009 8 60297-3-100 IEC:2008 5 Front panels 5.1 Front panel dimensions The height increment of a front panel is 1U, equal to 44,45 mm. There are two mounting hole types as shown in detail “A”. The front panel thickness is not def

36、ined by this standard. As shown in Figures 2 and 3 and Tables 1 and 2, front panels of 1U, 2U and 6U heights may be provided with different number of mounting holes. The higher number of mounting holes may be used in case of high load applied to the front panel or other stability requirements. For 6

37、U front panels two types of hole spacing are possible (see Table1 and Table 2). The front panel dimensions apply also to chassis and subracks. Detail A Mounting holes 10,3 0,4 13,5 0,4 6,8 14,7 1,2482,6 0,4 H1H3Detail A Height pitch line U U H2H3H1+ 0,50IEC 2057/08Dimensions in millimetres Figure 2

38、Front panel dimensions for 1U up to 6U Table 1 Front panel dimensions for 1U up to 6U Height units n U H1 0,4 H2 0,4 H3 0,4 21,83 1U (44,45) 43,65 31,75 5,95 44,45 21,83 2U (88,90) 88,10 76,20 5,95 3U (133,35) 132,55 57,15 37,70 4U (177,80) 177,00 101,60 37,70 5U (222,25) 221,45 146,05 37,70 6U (266

39、,70) 265,90 190,50 37,70 Dimensions are in millimetres and the tolerances are non-cumulative. BS EN 60297-3-100:200960297-3-100 IEC:2008 9 H3U Height pitch line Mounting hole dimensions (see detail A in Figure 2) Center line H4H2H1IEC 2058/08 Figure 3 Front panel dimensions for 6U up to 12U Table 2

40、Front panel dimensions for 6U up to 12U Height units n U H1 0,4 H2 0,4 H3 0,4 H4 0,4 6U (266,70) 265,90 190,50 37,70 76,20 7U (311,15) 310,35 234,95 37,70 57,15 8U (355,60) 354,80 279,40 37,70 76,20 9U (400,05) 399,25 323,85 37,70 120,65 10U (444,50) 443,70 368,30 37,70 165,10 11U (488,95) 488,15 41

41、2,75 37,70 146,05 12U (533,40) 532,60 457,20 37,70 190,50 Dimensions are in millimetres and tolerances are non-cumulative. BS EN 60297-3-100:2009 10 60297-3-100 IEC:2008 5.2 Front panel mounting hole positions. Figure 4 shows the front panel, subrack and chassis incremental U height and their corres

42、ponding mounting holes. 1U, 2U and 6U front panels mounting hole spacing may be chosen from two optional versions. The number of available mounting positions for front panels, subracks of the IEC 60297-3-101 series and chassis products may depend on environmental and/or application specific requirem

43、ents. Height pitch line NOTE The hole positions shown comply to the standard spacing of a rack/cabinet. The universal spacing is indicated by centre lines (see Figure 6). For mounting hole dimensions (see detail A in Figure 2). 12U 11U 10U 9U8U 7U6U6U 5U 4U 3U 2U 2U 1U 1U Optional hole spacing IEC 2

44、059/08Figure 4 Front panel mounting hole positions BS EN 60297-3-100:200960297-3-100 IEC:2008 11 6 Racks 6.1 Rack description The rack structures are defined as a series of vertical member pairs, spaced on a predetermined coordination width dimension (see Figure 5 and Table 3). They are typically an

45、chored to the floor at the lower part and to the ceiling and/or wall at the top. Each pair of vertical members will allow the attachment of front panels, chassis and subracks, in accordance with this series of standards. The coordination dimension of the fixed rack structures is equal to the theoret

46、ical centre distances within a suite of racks. Each vertical rack member may be separated from or combined with the vertical member of the adjacent rack, providing the width coordination dimension is maintained. The heights and depth of such structures are not covered by this standard. Table 3 Width

47、 dimension of fixed rack structures Dimensions in millimetres Width dimension WC500 525 550 600 Front panel Subrack Top view Front view WC Vertical member Chassis WC WC IEC 2060/08 Figure 5 Array of racks BS EN 60297-3-100:2009 12 60297-3-100 IEC:2008 6.2 Rack/cabinet mounting grid types I and II Th

48、e mounting grid applies to the rack and cabinet vertical members. Figure 6 illustrates the mounting grid in two different types: Type I: The holes correspond with the front panel, subrack and chassis mounting hole positions. Type II: The same grid includes additional mounting holes (universal hole s

49、pacing). These additional holes do not correspond to the front panel, chassis or subrack mounting holes (except the optional hole spacing at 1U and 2U). They may be used for the mounting of other structural parts, such as telescopic slide brackets or angles. Type II shall be used as the preferred mounting grid. The mounting positions provide for attachment hardware such as thread clips, nuts, integrat