EN 60115-8-1-2015 en Fixed resistors for use in electronic equipment - Part 8-1 Blank detail specification Fixed surface mount (SMD) low power film resistors for general electronic.pdf

《EN 60115-8-1-2015 en Fixed resistors for use in electronic equipment - Part 8-1 Blank detail specification Fixed surface mount (SMD) low power film resistors for general electronic.pdf》由会员分享，可在线阅读，更多相关《EN 60115-8-1-2015 en Fixed resistors for use in electronic equipment - Part 8-1 Blank detail specification Fixed surface mount (SMD) low power film resistors for general electronic.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFixed resistors for use in electronic equipmentPart 8-1: Blank detail specification: Fixed surface mount (SMD) low power film resistors for general electronic equipment, classification level GBS EN 60115-8-1:2015National forewordThis British Standard is the UK implementation

2、 of EN 60115-8-1:2015. ItThe UK participation in its preparation was entrusted to TechnicalCommittee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to includ

3、e all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 69055 6ICS 31.040.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This Britis

4、h Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60115-8-1:2015The CENELEC common modifications have been implemented at the appropriate places in the text.

5、 The start and finish of each common modification is indicated in the text by tags .is derived from IEC 60115-8-1:2014.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60115-8-1 May 2015 ICS 31.040.10 English Version Fixed resistors for use in electronic equipment - Part 8-1: Blank detail specif

6、ication: Fixed surface mount (SMD) low power film resistors for general electronic equipment, classification level G (IEC 60115-8-1:2014 , modified) Rsistances fixes utilises dans les quipements lectroniques - Partie 8-1: Spcification particulire cadre: Rsistances fixes couche et faible dissipation

7、pour montage en surface (CMS), pour les quipements lectroniques universels, niveau G de classification (IEC 60115-8-1:2014 , modifie) Festwiderstnde zur Verwendung in Gerten der Elektronik - Teil 8-1: Vordruck fr Bauartspezifikation - Oberflchenmontierbare (SMD) Schicht-Festwiderstnde niedriger Bela

8、stbarkeit fr Gerte der Elektronik, Klassifikationsstufe G (IEC 60115-8-1:2014 , modifiziert) This European Standard was approved by CENELEC on 2015-03-30. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th

9、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English,

10、French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Aust

11、ria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai

12、n, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of

13、exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60115-8-1:2015 E BS EN 60115-8-1:2015EN 60115-8-1:2015 - 2 - Foreword The text of document 40/2297/FDIS, future edition 2 of IEC 60115-8-1, prepared by IEC/TC 40 “Capacitors and resistors for electronic equ

14、ipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60115-8-1:2015. A draft amendment, which covers common modifications to IEC 60115-8-1 (40/2297/FDIS), was prepared by CLC/TC 40XB “Resistors“ and approved by CENELEC. The following dates are fixed: latest date by wh

15、ich this document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-03-30 latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2018-03-30 Clauses, subclauses, notes, tables, figures a

16、nd annexes which are additional to those in IEC 60115-8-1:2014 are prefixed “Z”. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endor

17、sement notice The text of the International Standard IEC 60115-8-1:2014 was approved by CENELEC as a European Standard with agreed common modifications. BS EN 60115-8-1:2015EN 60115-8-1:2015 - 3 - Annex ZA (normative) Normative references to international publications with their corresponding Europe

18、an publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

19、applies. NOTE 1 When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title E

20、N/HD Year IEC 60062 2004 Marking codes for resistors and capacitors EN 60062 + corrigendum Jan. 2005 2007 IEC 60063 - Preferred number series for resistors and capacitors EN 60063 - IEC 60068-2-1 - Environmental testing - Part 2-1: Tests - Test A: Cold EN 60068-2-1 - IEC 60068-2-2 - Environmental te

21、sting - Part 2-2: Tests - Test B: Dry heat EN 60068-2-2 - IEC 60115-1 (mod) - 2008 - Fixed resistors for use in electronic equipment - Part 1: Generic specification EN 60115-1 + A11 2011 2015 IEC 60115-8 (mod) 2009 Fixed resistors for use in electronic equipment - Part 8: Sectional specification - F

22、ixed surface mount resistors EN 60115-8 2012 IEC 60286-3 - Packaging of components for automatic handling - Part 3: Packaging of surface mount components on continuous tapes EN 60286-3 - IEC 60286-6 - Packaging of components for automatic handling - Part 3: Bulk case packaging for surface mount comp

23、onents EN 60286-6 - IEC 61193-2 2007 Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages EN 61193-2 2007 IEC 61760-1 - Surface mounting technology - Part 1: Standard method for the specification of surface mounting components

24、(SMDs) EN 61760-1 - BS EN 60115-8-1:2015 4 IEC 60115-8-1:2014 IEC 2014 CONTENTS FOREWORD . 7 0 Introduction 9 0.1 Scope of this blank detail specification 9 0.2 Function of this blank detail specification . 9 0.3 Identification of the detail specification and the resistor10 1 Scope 12 2 Normative re

25、ferences . 12 3 Terms and definitions. 13 4 Characteristics and ratings . 13 4.1 General . 13 4.2 Dimensions . 13 4.3 Ratings . 14 4.4 Resistance range and tolerance on resistance . 16 5 Tests and test severities 16 5.1 Insulation resistance . 17 5.2 Voltage proof 17 5.3 Variation of resistance with

26、 temperature 17 5.4 Short time overload . 17 5.5 Temperature rise . 18 5.6 Solderability 18 5.7 Resistance to soldering heat . 18 5.8 Rapid change of temperature 18 5.9 Climatic sequence . 19 5.9.1 General 19 5.9.2 Climatic sequence, dry heat . 19 5.9.3 Climatic sequence, cold . 19 5.9.4 Climatic se

27、quence, low air pressure . 19 5.9.5 Climatic sequence, damp heat, cyclic . 20 5.9.6 Climatic sequence, DC load . 20 5.9.7 Climatic sequence, final measurements 20 5.10 Damp heat, steady state test . 20 5.11 Endurance at 70 C . 21 5.12 Endurance at upper category temperature . 21 5.13 Component solve

28、nt resistance test 21 5.14 Solvent resistance of marking test . 21 5.15 Shear test . 21 5.16 Substrate bending test 22 5.17 Flammability 22 5.18 Electrostatic discharge (ESD) test . 22 6 Performance requirements . 24 6.1 Limits for change of resistance at tests 24 6.2 Insulation resistance . 24 6.3

29、Variation of resistance with temperature 25 BS EN 60115-8-1:20153.1Nominal resistance 13 IEC 60115-8-1:2014 IEC 2014 5 6.5 Solderability 25 6.6 Flammability 25 7 Marking, packaging and ordering information . 26 7.1 Marking of the component . 26 7.2 Packaging . 26 7.3 Marking of the packaging 26 7.4

30、Ordering information . 26 8 Additional information 27 8.1 General . 27 8.2 Storage and transportation 27 8.3 Substrate for assembly 27 8.4 Soldering process . 27 8.5 Use of cleaning agents or solvents 28 8.6 Coating or potting after assembly 28 9 Quality assessment procedures . 28 9.1 General . 28 9

31、.1.1 100 % test 28 9.1.2 Certificate of conformity (CoC) . 29 9.1.3 Certified test records of released lots . 29 9.2 Qualification approval 29 9.3 Maintenance of a qualification approval . 29 9.3.1 Quality conformance inspection 29 9.3.2 Non-conforming specimen 29 Annex A (normative) 0 resistors (ju

32、mper) 39 A.1 General . 39 A.2 Characteristics and ratings 39 A.3 Tests and test severities 39 A.4 Performance requirements 40 A.5 Marking, packaging and ordering information . 40 A.6 Additional information 40 A.7 Quality assessment procedures . 40 A.7.1 Test schedule for qualification approval 40 A.

33、7.2 Test schedule for quality conformance inspection . 40 Annex B (informative) Letter symbols and abbreviations . 42 B.1 Letter symbols . 42 B.2 Abbreviations 43 Annex X . 44Bibliography 45 Figure 1 Outline and dimensions 13 Figure 2 Derating curve 15 Table 1 Styles and dimensions . 14 Table 2 Clim

34、atic categories 14 Table 3 Ratings 15 BS EN 60115-8-1:20156.4 Temperature rise . 25 Deleted 6 IEC 60115-8-1:2014 IEC 2014 Table 4 Temperature coefficients, tolerances and resistance ranges for climatic category . / . / . 16 Table 5 Short time overload duration 18 Table 6 Remaining cycles of damp hea

35、t, cyclic test . 20 Table 7 Damp heat steady state test duration . 20 Table 8 Shear test force . 22 Table 9 ESD test voltages 23 Table 10 Limits for change of resistance 24 Table 11 Temperature coefficients and permissible change of resistance 25 Table 12 Test schedule for qualification approval 30

36、Table 13 Test schedule for quality conformance inspection . 34 Table A.1 Ratings for 0 resistors . 39 BS EN 60115-8-1:2015IEC 60115-8-1:2014 IEC 2014 7 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT Part 8-1: Blank detail specification: Fixed surface moun

37、t (SMD) low power film resistors for general electronic equipment, classification level G FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC i

38、s to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) an

39、d Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the

40、 IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly

41、as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that se

42、nse. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees un

43、dertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any a

44、ttestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest editi

45、on of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether dire

46、ct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensa

47、ble for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60115-8-1 h

48、as been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition, published in 1989 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the

49、 previous edition: It includes minor revisions related to tables, figures and references. BS EN 60115-8-1:2015 8 IEC 60115-8-1:2014 IEC 2014 Dedication to resistors of product classification level G, which is for general electronic equipment, typically operated under benign or moderate environmental conditions, like e.g. consumer products, or telecommunication user terminals. Implementation of the zero defect policy with the application of the single assessment l