EN 60068-2-60-2015 en Environmental testing - Part 2-60 Tests - Test Ke Flowing mixed gas corrosion test.pdf

《EN 60068-2-60-2015 en Environmental testing - Part 2-60 Tests - Test Ke Flowing mixed gas corrosion test.pdf》由会员分享，可在线阅读，更多相关《EN 60068-2-60-2015 en Environmental testing - Part 2-60 Tests - Test Ke Flowing mixed gas corrosion test.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationEnvironmental testingPart 2-60: Tests Test Ke: Flowing mixed gas corrosion testBS EN 60068-2-60:2015National forewordThis British Standard is the UK implementation of EN 60068-2-60:2015. It isidentical to IEC 60068-2-60:2015. It supersedes BS EN 60068-2.60:1996,which will be

2、 withdrawn on 29 June 2018.The UK participation in its preparation was entrusted to TechnicalCommittee GEL/104, Environmental conditions, classification and testing.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to i

3、nclude all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 82505 7ICS 19.140 Compliance with a British Standard cannot confer immunity fromlegal obligations.This Bri

4、tish Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60068-2-60:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60068-2-60 December 2015 ICS 19.

5、140 Supersedes EN 60068-2-60:1996 English Version Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test (IEC 60068-2-60:2015) Essais denvironnement - Partie 2-60: Essais - Essai Ke: Essai de corrosion dans un flux de mlange de gaz (IEC 60068-2-60:2015) Umweltprfungen -

6、 Teil 2-60: Prfungen - Prfung Ke: Korrosionsprfung mit strmendem Mischgas (IEC 60068-2-60:2015) This European Standard was approved by CENELEC on 2015-07-23. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

7、 the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (Englis

8、h, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of A

9、ustria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S

10、pain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights

11、of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60068-2-60:2015 E BS EN 60068-2-60:2015EN 60068-2-60:2015 (E) 2 European foreword The text of document 104/655/FDIS, future edition 3 of IEC 60068-2-60, prepared by IEC/TC 104 “Environmental conditions,

12、classification and methods of test“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60068-2-60:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsemen

13、t (dop) 2016-06-11 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-07-23 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible fo

14、r identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60068-2-60:2015 was approved by CENELEC as a European Standard without any modification. BS EN 60068-2-60:2015EN 60068-2-60:2015 (E) 3 Annex ZA (normative) Normative references to international

15、 publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the re

16、ferenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available h

17、ere: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60512-2-1 - Connectors for electronic equipment - Tests and measurements - Part 2-1: Electrical continuity and contact resistance tests - Test 2a: Contact resistance - Millivolt level method EN 60512-2-1 - IEC 60512-3-1 - Connectors for elec

18、tronic equipment - Tests and measurements - Part 3-1: Insulation tests - Test 3a: Insulation resistance EN 60512-3-1 - ISO 431 - Copper refinery shapes - - BS EN 60068-2-60:2015 2 IEC 60068-2-60:2015 IEC 2015 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references. 5 3 Test apparatus 5 4 Severities 6

19、 5 Preconditioning 6 6 Initial measurements 6 7 Testing 7 7.1 General . 7 7.2 Test specimens . 7 7.3 Corrosivity monitoring materials . 7 7.4 Testing procedure . 7 8 Recovery . 9 9 Final measurements 9 10 Information to be given in the relevant specification 9 11 Information to be given in the test

20、report 10 Annex A (normative) Corrosion monitoring copper coupons 11 A.1 General . 11 A.2 Nature and dimension . 11 A.3 Cleaning procedure . 11 Annex B (informative) Description of test apparatus 12 B.1 General . 12 B.2 Climatic system . 12 B.3 Test enclosure 13 B.4 Gas delivery system 14 B.5 Analys

21、ing system 14 B.5.1 Temperature and humidity 14 B.5.2 Gases 14 B.6 Other corrosion monitoring methods 15 B.6.1 Mass increase 15 B.6.2 Surface analysis of monitoring coupons 15 B.6.3 Visual examination . 16 B.7 Calibration of the chamber 16 Annex C (informative) Guide to the selection of methods and

22、test duration 17 C.1 Introductory remarks . 17 C.2 Function of corrosive gases used in the tests . 17 C.3 Use of the different test methods . 17 Bibliography . 19 Figure B.1 Example of test apparatus . 12 Table 1 Test conditions 6 BS EN 60068-2-60:2015IEC 60068-2-60:2015 IEC 2015 3 INTERNATIONAL ELE

23、CTROTECHNICAL COMMISSION _ ENVIRONMENTAL TESTING Part 2-60: Tests Test Ke: Flowing mixed gas corrosion test FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). T

24、he object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Speci

25、fications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations

26、 liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters e

27、xpress, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Com

28、mittees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nati

29、onal Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does

30、 not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they hav

31、e the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatso

32、ever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicat

33、ions is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standa

34、rd IEC 60068-2-60 has been prepared by IEC technical committee 104: Environmental conditions, classification and methods of test. This third edition cancels and replaces the second edition, published in 1995, and constitutes a technical revision. This edition includes the following significant techn

35、ical changes with respect to the previous edition: updated IEC format; updated normative references list; addition of information of the working volume; revision of the test procedure; revision of the figures in Annex B. BS EN 60068-2-60:2015 4 IEC 60068-2-60:2015 IEC 2015 The text of this standard

36、is based on the following documents: FDIS Report on voting 104/655/FDIS 104/656/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

37、 A list of all parts in the IEC 60068 series, published under the general title Environmental testing, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.i

38、ec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 60068-2-60:2015IEC 60068-2-60:2015 IEC 2015 5 ENVIRONMENTAL TESTING Part 2-60: Tests Test Ke: Flowing mixed gas corrosion test 1 Scop

39、e This part of IEC 60068-2 determines the corrosive influence of operating and storage indoor environments on electrotechnical products components, equipment and materials, particularly contacts and connections, considered separately, integrated into a subassembly or assembled as a complete equipmen

40、t. It provides test methods giving information, on a comparative basis, to aid the selection of materials, choice of production processes and component design, with regard to corrosion resistance. A guide to the selection of methods and test duration is provided in Annex C. 2 Normative references Th

41、e following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512

42、-2-1, Connectors for electronic equipment Tests and measurements Part 2-1: Electrical continuity and contact resistance tests Test 2a: Contact resistance Millivolt level resistance method IEC 60512-3-1, Connectors for electronic equipment Tests and measurements Part 3-1: Insulation tests Test 3a: In

43、sulation resistance ISO 431, Copper refinery shapes 3 Test apparatus The test apparatus consists of a climatic system, test enclosure, gas delivery system and means for measuring gas concentration. Details of design and construction are optional but shall be such that the conditions specified for ea

44、ch method are fulfilled throughout the working volume and shall comply with the following requirements: water droplets or aerosols shall not be injected into the test enclosure; air and water used shall be sufficiently clean in order not to affect performance of the test; the test atmosphere shall f

45、low through the enclosure in such a manner as to ensure uniform test conditions within the working volume; the sampling point for gas analysis shall be in the working volume of the test enclosure; the exhaust gases shall be treated in accordance with the relevant regulatory stipulations; the wet bul

46、b pod shall be placed in the test chamber in such a manner not to exceed 0,1 % of the cross-section of the test chamber. BS EN 60068-2-60:2015 6 IEC 60068-2-60:2015 IEC 2015 Because of the strong synergistic effect and the so called “memory effect” (i.e., it is difficult to fully remove the chlorine

47、 compounds from the chamber, tubes, etc.), it is recommended that enclosures and tubing used for tests that incorporate chlorine only be used for chlorine tests. The working volume is the volume within which the individual corrosion (mass increase of copper coupons expressed in mg/( dm2 day) accordi

48、ng to Annex A) at each location differs by a maximum of 15 % from the average corrosion of all coupons within the working volume. 4 Severities The test severity shall be given in the relevant specification. It is defined by the test method, chosen from Table 1, the test duration. Preferred durations

49、, in days, are 4, 7, 10, 14 and 21. Four methods are defined. The different parameters for each method are summarized in the following Table 1. A guidance for the use of each method is given in Clause C.3. Table 1 Test conditions Parameters Method 1 Method 2 Method 3 Method 4 H2S (109vol/vol) 100 20 10 5 100 20 10 5 NO2(109vol/vol) 200 50 200 50 200 20 Cl2(109vol/vol) 10 5 20 5 10 5 SO2(109vol/vol) 500 100 200 20 Temper