EN 50289-4-2-2001 en Communication Cables - Specifications for Test Methods Part 4-2 Environmental Test Methods - Water Penetration《通信电缆 试验方法规范 第4-2部分 环境试验方法 水渗透》.pdf

《EN 50289-4-2-2001 en Communication Cables - Specifications for Test Methods Part 4-2 Environmental Test Methods - Water Penetration《通信电缆 试验方法规范 第4-2部分 环境试验方法 水渗透》.pdf》由会员分享，可在线阅读，更多相关《EN 50289-4-2-2001 en Communication Cables - Specifications for Test Methods Part 4-2 Environmental Test Methods - Water Penetration《通信电缆 试验方法规范 第4-2部分 环境试验方法 水渗透》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD C ornrnunication cables Specifications for test methods Part 4-2: Environmental test methods - Water penetration The European Standard EN 502894-2:2001 has the status of a British Standard ICs 33.120.10 BS EN 5028942:200 1 Wk present to the responsible European committee any enquiri

2、es on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cr oss-r e fer enc e s

3、 The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue.

4、 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises

5、 a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 13 November 2001 ISBN O 580 38682 I EUROPEAN STANDARD EN 50289-4-2 NORME EUROPENNE EUROP

6、f ISCHE NORM October 2001 ICs 33.120.10 English version Communication cables Specifications for test methods Part 4-2: Environmental test methods Water penetration C, b I es de communication Spcifications des mthodes dessai Partie 4-2: Mthodes dessais denvironnement Eindringen von Wasser P n tra t i

7、o n d ea u Kommunikationskabel Spezifikationen far Prfverfahren Teil 4-2: UmweltprJfverfahren - This European Standard was approved by CENELEC on 2001-05-01. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard

8、the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French,

9、German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czec

10、h Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europo/o&ches Komi

11、tee f, r Elektrotechnische Normung Central Secretariat: rue de Stassart 35. B - 1050 Brussels O 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50289-4-2:2001 E EN 50289-4-2 12001 -2- Foreword This European Standard was prepa

12、red by the Technical Committee CENELEC TC 46X, Com m unicat ion cables. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50289-4-2 on 2001-05-01. The following dates were fixed: latest date by which the EN has to be implemented at national leve

13、l by publication of an identical national standard or by endorsement (d0P) 2002-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (daw) 2004-04-0 1 This European Standard has been prepared under the European Mandate M/212 given to CENELEC by the European

14、Commission and the European Free Trade Association. -3- Contents EN 50289-4-2 12001 4 Normat ive references 4 4 Test methods 4 4.1 Sample 4 Method A . 4 Method B . 4 4.2 Equipment 5 4.3 Procedure 5 4.4 Requirement 5 4.5 Details to be 5 5 Test report 5 4. I. I 4.1.2 EN 50289-4-2 12001 -4- 1 Scope Thi

15、s Part 4-2 of EN 50289 details the method of test to determine the ability of a cable used in analogue and digital communication systems to block water migration along a specified length. This test applies to water-blocked cables. It is to be read in conjunction with Part 4-1 of EN 50289, which cont

16、ains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated

17、 references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to appl ies (including am endm ents). EN 50289-4-1 2001 Commun

18、ication cables - Specifications for test methods Part 4-1 : Environmental test methods - General requirements Communication cables - Part 1-2: Definitions EN 50290-1-21) 3 Definitions For the purposes of this European Standard, the definitions of EN 50290-1-2 apply. 4 Test methods Compliance shall b

19、e checked on samples of cable using one of the two following methods (A or B), as stated in the detail specification. Method A tests for water migration between the outer interstices of the core and the outer sheath, whilst method B tests for water migration over the entire cross-section designed to

20、 be water-blocked. 4.1 Sample 4.1.1 Method A A circumferential portion of sheath and wrapping 25 mm wide shall be removed 3 m from one end of a sample length of cable and a watertight sleeve shall be applied over the exposed core so as to bridge the gap in the sheath, and allow a 1 m height of water

21、 to be applied. 4.1.2 Method B A cable sample having a length 1 m longer than the length to be tested, which shall not exceed 3 m. If required, the sample is submitted to the bending procedure. A maximum cable length of 3 m shall then be taken from the central portion of the sample. A watertight sea

22、l shall be applied to one end of the sample to allow a 1 m height of water to be applied. NOTE application of the seal. For armoured cables where the armour is not designed to be water-blocked, the armour may be removed before the 1) At draft stage -5- EN 50289-4-2 12001 4.2 Equipment Suitable test

23、arrangements are shown in Figure 1 4.3 Procedure Unless otherwise specified in the detail specification, the sample shall be supported horizontally and a 1 m height of water shall be applied for 24 h at a temperature of (20 15) OC. A water soluble fluorescent dye or other suitable colourant may be u

24、sed to aid in the detection of water seepage. Care should be taken in choosing a fluorescent dye that does not react with any of the cable components. 4.4 Req u i remen ts No water shall be detected at the unsealed end of the sample. If a fluorescent dye is used, an ultraviolet light may be used for

25、 the examination. NOTE The test procedure mentioned above is a basic compliance requirement and for routine tests, samples of shorter length may be tested for a shorter time. 4.5 Details to be specified The detail specification shall include : a) b) c) method used and cross-section tested, bending p

26、rocedure applied, where applicable, quantity and type of dye, where applicable. 5 Test report The test report shall include: number of samples, test temperature, sample length, pass/fail criteria EN 50289-4-2 12001 -6- Im Height of water Sample t Figure la - Method A Water seal lm Figure 1 b - Metho

27、d B Figure 1 -Water penetration test BS EN 50289-4-212001 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re

28、 vi si ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy

29、or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that sub

30、scribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-

31、. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standar

32、ds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 71 11. Fax: 020 8996 7048. Subscribing members of BSI are kept up to d

33、ate with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Cop

34、yright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted

35、in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.