EN 16297-2-2012 en Pumps - Rotodynamic pumps - Glandless circulators - Part 2 Calculation of energy efficiency index (EEI) for standalone circulators《泵 旋转动力泵 无密封垫的循环器 单机循环器的能源效率指数(.pdf

《EN 16297-2-2012 en Pumps - Rotodynamic pumps - Glandless circulators - Part 2 Calculation of energy efficiency index (EEI) for standalone circulators《泵 旋转动力泵 无密封垫的循环器 单机循环器的能源效率指数(.pdf》由会员分享，可在线阅读，更多相关《EN 16297-2-2012 en Pumps - Rotodynamic pumps - Glandless circulators - Part 2 Calculation of energy efficiency index (EEI) for standalone circulators《泵 旋转动力泵 无密封垫的循环器 单机循环器的能源效率指数(.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16297-2:2012Pumps Rotodynamic pumps Glandless circulatorsPart 2: Calculation of energy efficiencyindex (EEI) for standalone circulatorsBS EN 16297-2:2012 BRITISH STANDARDNa

2、tional forewordThis British Standard is the UK implementation of EN 16297-2:2012.It supersedes BS EN 1151-1:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/6, Pumps and pump testing.A list of organizations represented on this committee can beob

3、tained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 75132 5ICS 23.080Compliance with a

4、 British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate Text affectedBS EN 16297-2:2012 BRITISH STANDARDNational forewordThis Britis

5、h Standard is the UK implementation of EN 16297-2:2012.It supersedes BS EN 1151-1:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/6, Pumps and pump testing.A list of organizations represented on this committee can beobtained on request to its s

6、ecretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 75132 5ICS 23.080Compliance with a British Standard cannot c

7、onfer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate Text affectedStandards Policy and Strategy Committee on 30 November 2012.Amendments/corrigenda issued

8、since publicationDate Text affectedTogether with BS EN 16297-1:2012, it supersedes BS EN 1151-1:2006, which is withdrawn.BS EN 16297-2:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16297-2 October 2012 ICS 23.080 English Version Pumps - Rotodynamic pumps - Glandless circulators - Part 2:

9、Calculation of energy efficiency index (EEI) for standalone circulators Pompes - Pompes rotodynamiques - Circulateurs sans presse-toupe - Partie 2: Calcul de lindice defficacit nergtique (EEI) pour les circulateurs indpendants Pumpen - Kreiselpumpen - Umwlzpumpen in Nassluferbauart - Teil 2: Berechn

10、ung des Energieeffizienzindexes (EEI) von externen Umwlzpumpen This European Standard was approved by CEN on 18 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard wi

11、thout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any othe

12、r language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,

13、Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMI

14、TTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16297-2:2012: EBS EN 16297-2:2012EN 16

15、297-2:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Symbols and units .55 Performance requirements and safety requirements 56 Calculation of energy efficiency index (EEI) .56.1 General conditions 56.2 Procedure .66.2.1 Load profile for

16、 calculation of average compensated power input, PLavg66.2.2 Part load operating points 66.2.3 Calculation of average compensated power input, PL,avg.66.2.4 Calibration factor .66.2.5 Calculation of energy efficiency index (EEI), EEI.6Annex ZA (informative) Relationship between this European Standar

17、d and the requirements of Commission Regulation (EC) No 641/2009 .8BS EN 16297-2:2012EN 16297-2:2012 (E) 3 Foreword This document (EN 16297-2:2012) has been prepared by Technical Committee CEN/TC 197 “Pumps”, the secretariat of which is held by AFNOR. This European Standard shall be given the status

18、 of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject o

19、f patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). Fo

20、r relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document, together with EN 16297-1:2012, supersedes EN 1151-1:2006. EN 16297 consists of the following parts under the general title Pumps Rotodynamic pumps Glandless circulators: Part 1:

21、General requirements and procedures for testing and calculation of energy efficiency index (EEI); Part 2: Calculation of energy efficiency index (EEI) for standalone circulators; Part 3: Energy efficiency index (EEI) for circulators integrated in products. According to the CEN/CENELEC Internal Regul

22、ations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, It

23、aly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16297-2:2012EN 16297-2:2012 (E) 4 Introduction The European Standard has been prepared under mandate M/469 EN of 22 June 201

24、0 given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Requirements of the EU Directive 2005/32/EC of 6 July 2005 and Commission Regulation (EC) 641/2009 of 22 July 2009 by describing procedures for measurement and calculation of hydraul

25、ic power, power consumption, and energy efficiency index of circulators. BS EN 16297-2:2012EN 16297-2:2012 (E) 5 1 Scope This European Standard specifies the procedure for calculating the energy efficiency index (EEI) of standalone circulators. 2 Normative references The following documents, in whol

26、e or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 809:1998+A1 :2009, Pumps and pump un

27、its for liquids Common safety requirements EN 16297-1:2012, Pumps Rotodynamic pumps Glandless circulators Part 1: General requirements and procedures for testing and calculation of energy efficiency index (EEI) EN 60335-2-51:2003, Household and similar electrical appliances Safety Part 2-51: Particu

28、lar requirements for stationary circulation pumps for heating and service water installations 3 Terms and definitions For the purpose of this document, the terms and definitions given in EN 16297-1:2012 and the following apply. 3.1 standalone circulator circulator designed to operate independently f

29、rom a product that generates and/or transfers heat Note 1 to entry For the purpose of this document, the term circulator is used in the following in place of standalone circulator. 3. 2 differential pressure controlled circulator circulator adapting in time the differential pressure to the demand by

30、 varying the speed 4 Symbols and units For the purpose of this document, the symbols, quantities and units given in Table 1 of EN 16297-1:2012 apply. 5 Performance requirements and safety requirements The requirements of EN 16297-1, EN 809 and EN 60335-2-51 apply. 6 Calculation of energy efficiency

31、index (EEI) 6.1 General conditions Standalone circulators with pump housing shall be measured as a complete unit. BS EN 16297-2:2012EN 16297-2:2012 (E) 6 Standalone circulators without pump housing shall be measured in pump housing identical to the pump housing in which they are intended to be used.

32、 6.2 Procedure 6.2.1 Load profile for calculation of average compensated power input, PLavgThe load profile for calculation of average compensated power input, PLavg, for standalone circulators is shown in Table 1. Table 1 Load profile for calculation of average compensated power input, PL,avgQ in %

33、 of Q100%Time in % of annual operating hours 100 L1 = 6 75 L2 = 15 50 L3 = 35 25 L4 = 44 6.2.2 Part load operating points Part load operating points are measured by using following procedure: a) Calculate Hrefat each part load point on the reference control curve (see Figure 4 in EN 16297-1:2012). b

34、) Select and set a control curve (control curve or non-controlled curve) which is as close as possible to the reference control curve and reaches point (Q100%, H100%) within the tolerance of H100%. c) Change the system curve to reach the part load operating points. 6.2.3 Calculation of average compe

35、nsated power input, PL,avgThe average compensated power input, PL,avg, is calculated as: PP PPPPPPP= + + += +L,avg 1 L,100% 2 L,75% 3 L,50% 4 L,25%L,100% L,75% L,50% L,25%L LLL0,06 0,15 0,35 0,44PL,avgmust be based on measurements from 100 % flow to 0 % flow or as average of PL,avgbased on data meas

36、ured from 0% flow to 100% flow and 100 % flow to 0 % flow. If more than one control curve reaches the point (Q100%, H100%) within the tolerance of H100%, it is recommended to make the calculation on more than one curve and use the curve which gives the lowest PL,avg. 6.2.4 Calibration factor The cal

37、ibration factor for standalone circulators isCC= =20%xx%0,49 . 6.2.5 Calculation of energy efficiency index (EEI), EEIThe energy efficiency index (EEI), EEI, for standalone circulators is calculated as: BS EN 16297-2:2012EN 16297-2:2012 (E) 7 L,avg L,avgEEI 20%ref ref0,49PPC = It is permissible to s

38、ubstitute the parameter EEIby the abbreviation EEI in data sheets, manuals, leaflets, brochures etc. BS EN 16297-2:2012EN 16297-2:2012 (E) 8 Annex ZA (informative) Relationship between this European Standard and the requirements of Commission Regulation (EC) No 641/2009 This European Standard has be

39、en prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to requirements Commission Regulation (EC) No 641/2009 of 22 July 2009: implementing Directive 2005/32/EC1of the European Parliament and of the Council with re

40、gard to ecodesign requirements for glandless standalone circulators and glandless circulators integrated in products Once this standard is cited in the Official Journal of the European Union under that Commission Regulation , compliance with the clauses of this standard given in Table ZA.1 confers,

41、within the limits of the scope of this standard, a presumption of conformity with the corresponding requirements of that and associated EFTA regulations. Table ZA.1 Correspondence between this European Standard and Commission Regulation (EC) No 641/2009 Clauses and sub-clauses of this EN Requirement

42、s of CommissionRegulation (EC) No 641/2009 Qualifying remarks/Notes Part 1: 6.2.1 Annex II, 2., 3. Calculation of Phyd Part 1: 6.2.2 Annex II, 2., 4. Calculation of Pref Part 1: 6.2.4 Annex II, 2., 5. Reference control curve Part 1: 6.2.9 Annex II, 2., 9. Calculation of EEI Part 2: 6.2.5 Annex II, 2

43、., 9. Calculation of EEI Part 3: 6.2.5 Annex II, 2., 9. Calculation of EEI WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard. 1The Directive was replaced by the Directive 2009/125/EC. This page deliberately left blankBSI

44、is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardis

45、ation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards an

46、d PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical c

47、ommittee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers auto

48、matically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and

49、 foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on n