EN 16146-2012 en Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification (Incorporates Amendment A1 .pdf

《EN 16146-2012 en Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification (Incorporates Amendment A1 .pdf》由会员分享，可在线阅读，更多相关《EN 16146-2012 en Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification (Incorporates Amendment A1 .pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationSanitary tapware Extractable shower hoses forsanitary tapware for supplysystems type 1 and type 2 General technical specificationBS EN 16146:2012+A1:2014BS EN 16146:2012+A1:2014National forewordThis British Standard is the UK implementation of EN 16146:2012+A1:2014. It super

2、sedes BS EN 16146:2012, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“.The UK participatio

3、n in its preparation was entrusted by Technical Committee B/504, Water supply, to Subcommittee B/504/-8, Sanitary tapware. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions o

4、f a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014ISBN 978 0 580 85652 5ICS 91.140.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under

5、 the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments/corrigenda issued since publicationDate Text affected31 December 2014 Implementation of CEN amendment A1:2014BRITISH STANDARDEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16146:2012+A1 November 2014 IC

6、S 91.140.70 Supersedes EN 16146:2012English Version Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification Robinetterie sanitaire - Flexibles de douchettes extractibles pour robinetterie sanitaire pour les systmes dalim

7、entation en eau de types 1 et 2 - Spcifications techniques gnrales Sanitrarmaturen - Ausziehbare Brauseschluche fr Sanitrarmaturen fr Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation This European Standard was approved by CEN on 10 November 2012 and includes Amendme

8、nt 1 approved by CEN on 9 September 2014.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning suc

9、h national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own

10、 language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, G

11、reece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMU

12、NG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16146:2012+A1:2014 E2 Contents Page Foreword 4 Introduction .5 1 Scope 6 2 Normative references 8 3 Terms and

13、definitions .9 4 Designation 9 5 Marking .9 6 Materials .9 6.1 Chemical and hygienic requirements 9 6.2 Exposed surface condition and quality of coating 9 7 Dimensional characteristics 10 7.1 General . 10 7.2 Connecting dimensions . 10 7.3 Special cases 11 8 Hydraulic characteristics . 11 8.1 Genera

14、l . 11 8.2 Flow rate 11 8.2.1 Test method . 11 8.2.2 Principle . 11 8.2.3 Apparatus 12 8.2.4 Procedure 12 8.2.5 Requirements 12 9 Mechanical and leaktightness characteristics 13 9.1 General . 13 9.2 Tensile strength 13 9.2.1 Test method . 13 9.2.2 Principle . 13 9.2.3 Apparatus 13 9.2.4 Procedure 14

15、 9.2.5 Requirements 14 9.3 Flexing durability test . 14 9.3.1 Test Method . 14 9.3.2 Principle . 14 9.3.3 Apparatus 14 9.3.4 Procedure 15 9.3.5 Requirement 16 9.4 Durability test 16 9.4.1 Test Method . 16 9.4.2 Principle . 16 9.4.3 Apparatus 16 9.4.4 Procedure 16 9.4.5 Requirement 16 9.5 Pressure re

16、sistance at elevated temperature 17 9.5.1 Test method . 17 9.5.2 Principle . 17 9.5.3 Apparatus 17 BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)3 9.5.4 Procedure . 18 9.5.5 Requirements . 19 9.6 Thermal shock test 19 9.6.1 Test method . 19 9.6.2 Principle 19 9.6.3 Apparatus . 19 9.6.4 Procedure

17、 . 20 9.6.5 Requirements . 20 10 Rotary connection . 20 10.1 General . 20 10.2 Test Method . 20 10.2.1 Principle 20 10.2.2 Apparatus . 20 10.2.3 Procedure . 21 10.2.4 Requirements . 21 Annex A (informative) Pressure take-off tee 22 Bibliography 25 BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)4

18、Foreword This document (EN 16146:2012+A1:2014) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the

19、latest by May 2015, and conflicting national standards shall be withdrawn at the latest by May 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such

20、patent rights. This document includes Amendment 1 approved by CEN on 9 September 2014. This document supersedes EN 16146:2012. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. According to the CEN/CENELEC Internal Regulations, the national standard

21、s organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem

22、bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)5 Introduction In respect of potential adverse effects on the quality of water intended for human consumption

23、 caused by the product covered by this standard, this standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regu

24、lations concerning the use and/or the characteristics of this product remain in force. BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)6 1 Scope This European Standard applies to hoses for extractable outlets of any material intended for equipping sanitary tapware for sinks and basins. Such hoses

25、will only be connected downstream of the obturator of the tapware. The tapware will comply with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see 1, 2, 3, 5 and 6). Hoses intended to connect sanitary tapware to the water supplies are not covered by this standard. This European Standard specifies: the

26、 dimensional, mechanical and hydraulic characteristics with which the hose for extractable outlets shall comply; the procedures for testing these characteristics. Details of pressures and temperatures are given in Table 1. ! Table 1 Conditions of use/Classifications Water supply system Operating ran

27、ge of hoses for extractable outlets Flow rates (Q)aLimits Recommended Type 1 see Figure 1Dynamic Pressure 0,05 MPa P 0,5 MPa (0,5 bar P 5 bar) Dynamic Pressure 0,1 MPa to 0,3 MPa (1,0 bar to 3,0 bar) Class 1: Q 0,25 l/s (15 l/min) Class 2: Q 0,15 l/s (9 l/min) Type 2 see Figure 2Dynamic Pressure 0,0

28、1 MPa to 0,2 MPa (0,1 bar to 2,0 bar) Dynamic Pressure 0,02 MPa to 0,10 MPa (0,2 bar to 1,0 bar) Class E: 0,06 l/s Q 0,18 l/s (3,6 l/min Q 10,8 l/min.) Class H: 0,18 l/s Q (10,8 l/min Q) Temperature T 70C T 60C aSee details in Table 3. “ BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)7 Key 1 cold

29、 water 2 hot water 3 mains supply pipe (Supply pressures up to 1,0 MPa (10 bar) 4 water heater Figure 1 Type 1 Supply system - with a pressure range of 0,05 MPa to 1,0 MPa (0,5 bar to 10 bar) BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)8 Key 1 cold water storage cistern (cover omitted for clar

30、ity) 2 warning pipe 3 vent pipe 4 hot water cylinder 5 alternative cistern fed cold supply to sanitary appliances 6 to boiler 7 mains supply pipe (Supply pressures up to 1,0 MPa (10 bar) Figure 2 Type 2-Supply system - with a pressure range of 0,01 MPa to 1,0 MPa, (0,1 bar to 10 bar): A vented domes

31、tic hot water and cold water supply system incorporating gravity hot water, mains cold water and alternative gravity cold water supply to sanitary appliances 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its

32、 application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 248, Sanitary tapware General specification for electrodeposited coatings of Ni-Cr EN ISO 228-1, Pipe threads where pressur

33、e-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)9 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 hose for extractable outlets flexible su

34、pply pipe which connects sanitary tapware to an extractable outlet 4 Designation Hoses for extractable outlets complying with this standard, are designated by: type; connecting thread dimensions e.g. G 1/2 G 1/2 or G 1/2 G 3/4; length; material of the external sheath (plastic, metal); type of nuts a

35、nd if conical the dimension C; reference to this standard: EN 16146; flow rate Class (see Table 1). EXAMPLE Hose for extractable outlet type, G 1/2, cone 26 G 3/4, length 1,5m, metal sheath, EN 16146, Class H. 5 Marking Extractable hoses complying with this standard shall be marked permanently and l

36、egibly with the manufacturers mark or the suppliers mark. The flow rate class shall appear on the product but it need not be permanent. Hoses for extractable outlets with special dimensions (see 7.3) delivered together with the tapware need not be marked individually. 6 Materials 6.1 Chemical and hy

37、gienic requirements All materials coming into contact with water intended for human consumption shall present no risk to health. They shall not cause any change of the drinking water in terms of quality, appearance, smell or taste. 6.2 Exposed surface condition and quality of coating Visible chromiu

38、m plated surfaces and Ni-Cr coatings shall comply with the requirements of EN 248. BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)10 7 Dimensional characteristics 7.1 General General comment on design: the design and construction of components without defined dimensions permits various design sol

39、utions to be adopted by the manufacturer; permitted deviations from the defined dimensions are given in 7.3. 7.2 Connecting dimensions The connecting dimensions of hoses for extractable outlets are specified in Table 2 and Figures 3 to 5. Table 2 Connecting dimensions Dimensions Values Comments A G

40、1/2, G 3/8 or 15 1 mm or other EN ISO dimensions Connecting thread (tap side) B G 1/2 Connecting thread (extractable outlet side) EN ISO 228-1 C 23 0501,+mm or 26 0501,+mm Major diameter of conical nut (if provided) G 8,5 0/-1 mm Functional dimension on seal depth I 1,5 005,+mm Thread counter bore K

41、 30 mm Total length of conical nut 3 0/-1 mm Cone angle (if provided) L 500 mm Total length of hose a) Conical nut b) Nut (shape unspecified) Figure 3 Terminal nuts BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)11 Figure 4 Female or male end (shape unspecified) Figure 5 Hose length 7.3 Special c

42、ases Hoses for extractable outlets intended for special applications e.g. when interchangeability is not a requirement, can incorporate the following dimensional deviations: connection to the tapware is guaranteed; threaded connections are in compliance with ISO standards; all other requirements of

43、this standard are satisfied; the manufacturers literature, including the installation instructions supplied with the hoses for extractable outlets, indicates clearly that the hoses for extractable outlets are special cases. 8 Hydraulic characteristics 8.1 General The test described is a type test (l

44、aboratory test) and not a quality control test carried out during manufacture. 8.2 Flow rate 8.2.1 Test method This clause describes a method for testing the flow rate of hoses. 8.2.2 Principle The principle consists of a method for measuring the flow rate through the hoses for extractable outlets u

45、sing cold water (T 30 C) in order to determine the flow rate class of the hose (see Table 1). The flow rate of hoses for extractable outlets with special connection (see 7.3) delivered together with the tapware is measured in combination with the complete sanitary tapware. BS EN 16146:2012+A1:2014 E

46、N 16146:2012+A1:2014 (E)12 8.2.3 Apparatus The test apparatus is shown in Figure 6. 8.2.4 Procedure Connect the G 1/2 size nut of the hose for extractable outlets to the pressure take-off tee, supporting the hose in a horizontal position; apply the required dynamic pressure using the horizontal axis

47、 of the hose as a datum; record the flow rate “Q” (Table 1) after stabilisation. 8.2.5 Requirements Hoses for extractable outlets shall be classified according to the flow rate value “Q” at the required pressure as shown in Table 3. ! Table 3 Flow rate classes Supply system Flow rate / Pressure Type

48、 1 Class 1 Q 0,25 l/s (15 l/min) at (0 02003,+) MPa (0203,+) bar) Class 2 Q 0,15 l/s (9 l/min) at (0 02003,+) MPa (0203,+) bar) Type 2 Class E 0,06 l/s Q 0,18 l/s (3,6 l/min Q 10,8 l/min) at (0 00200 01,+) MPa (0 02001,+) bar) Class H 0,18 l/s Q (10,8 l/min Q) at (0 00200 01,+) MPa (0 02001,+) bar)

49、“ BS EN 16146:2012+A1:2014 EN 16146:2012+A1:2014 (E)13 Key 11 supply circuit: 1 a means for supplying and maintaining the required pressures and temperatures of Table 3 with an accuracy of 1 % of the test value 2 a pipe 3 a device for measuring the flow rate with an accuracy of 2 % of the test value 4 a stop valve 5 a pressure measuring device with an accuracy of 1 % of the test value 6 a temperature measuring device with an acc