EN 16145-2012 en Sanitary tapware - Extractable outlets for sink and basin mixers - General technical specification《卫生tapware 可抽出的渠道下沉盆地搅拌机 通用技术规范》.pdf

《EN 16145-2012 en Sanitary tapware - Extractable outlets for sink and basin mixers - General technical specification《卫生tapware 可抽出的渠道下沉盆地搅拌机 通用技术规范》.pdf》由会员分享，可在线阅读，更多相关《EN 16145-2012 en Sanitary tapware - Extractable outlets for sink and basin mixers - General technical specification《卫生tapware 可抽出的渠道下沉盆地搅拌机 通用技术规范》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16145:2012Sanitary tapware Extractable outlets for sinkand basin mixers Generaltechnical specificationBS EN 16145:2012 BRITISH STANDARDNational forewordThis British Standar

2、d is the UK implementation of EN 16145:2012.The UK participation in its preparation was entrusted to TechnicalCommittee B/504/-/8, Sanitary tapware.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the ne

3、cessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 71792 5ICS 91.140.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard wa

4、s published under the authority of theStandards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate Text affectedBS EN 16145:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16145 December 2012 ICS 91.140.70 English Version Sanitary tapware - Extractable

5、outlets for sink and basin mixers -General technical specification Robinetterie sanitaire - Douchettes extractibles pour mitigeurs dviers et de lavabos - Spcifications techniques gnrales Sanitrarmaturen - Ausziehbare Auslufe fr Waschtisch- und Splbeckenarmaturen - Allgemeine technische Spezifikation

6、 This European Standard was approved by CEN on 10 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical r

7、eferences concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a

8、 CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Maced

9、onia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EURO

10、PISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16145:2012: EBS EN 16145:2012EN 16145:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52

11、 Normative references 93 Terms and definitions .94 Classification 95 Designation . 106 Marking 107 Materials 107.1 Chemical and hygienic requirements . 107.2 Exposed surface condition and quality of coating . 108 Dimensional Characteristics . 108.1 General . 108.2 Connecting Dimensions . 108.3 Speci

12、al Cases 119 Leaktightness Characteristics . 119.1 Leaktightness of the inlet connection and the spray plate 119.2 Leaktightness of manually operated spray mode selector 139.3 Leaktightness and operation of spray mode selectors with automatic return 1310 Mechanical Characteristics . 1410.1 General .

13、 1410.2 Mechanical Strength . 1410.3 Mechanical endurance of spray mode selectors . 1510.4 Thermal Shock Test 1711 Hydraulic Characteristics 1811.1 General . 1811.2 Flow rate Test method . 1812 Backflow protection 2012.1 General . 2012.2 Standard connection 2112.3 Special connection . 2213 Acoustic

14、characteristics 2313.1 General . 2313.2 Procedure 2313.3 Expression of results . 2313.4 Determination of acoustic group 2314 Rotary connection 2314.1 General . 2314.2 Test method . 23Annex A (informative) Pressure take-off tee 25Bibliography . 28BS EN 16145:2012EN 16145:2012 (E) 3 Foreword This docu

15、ment (EN 16145:2012) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and c

16、onflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According

17、 to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Gre

18、ece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16145:2012EN 16145:2012 (E) 4 Introduction In respect of potential adverse effects on the

19、quality of water intended for human consumption, caused by the product covered by this standard: This standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. It should be noted that, while awaiting the adoption of veri

20、fiable European criteria, existing national regulations concerning the use and/or the characteristics of these products remain in force. This European Standard specifies requirements for shower outlets suitable for use in water supply systems of Type 1 and Type 2. BS EN 16145:2012EN 16145:2012 (E) 5

21、 1 Scope This European Standard specifies: the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply; the procedures for testing these characteristics. It applies to extractable outlet

22、s made from any material which is intended for equipping and supplementing sanitary tapware for sinks and wash-basins used for culinary or ablutionary purposes. Such extractable outlets shall only be connected downstream of the obturator of the tapware. Extractable outlets with total closing device

23、fitted after the obturator of the tapware are not covered by this standard. Such products will be tested in accordance with EN 200, EN 817, EN 1111, EN 1286 or EN 1287 (see 1, 2, 3, 5 and 6). The conditions of use and classification are specified in Table 1. BS EN 16145:2012EN 16145:2012 (E) 6 Table

24、 1 Conditions of use/Classifications Water Supply system Operating range of extractable shower outlets Flow rate classes Acoustics Marking Limits Recommended See Clause 13 See Clause 4 Type 1 see Figure 1Dynamic Pressure (0,05 to 0,5) MPa (0,5 to 5,0) bar) Dynamic Pressure (0,1 to 0,3) MPa (1,0 to 3

25、,0) bar) ZE (0,066 7 Q (0,01 to 0,2) MPa (0,1 to 2,0) bar) Dynamic Pressure (0,02 to 0,1) MPa(0,2 to 1,0) bar) EE (0,025 Q 0,06) l/s (1,5 Q 3,6) l/min) at 0,01 MPa (0,1 bar) (unclassified)E (0,06 Q 0,14) l/s (3,6 Q 8,4) l/min) at 0,01 MPa (0,1 bar) H (Q 0,14) l/s (Q 8,4) l/min) at 0,01 MPa (0,1 bar)

26、 Temperature T 70 C T 42 C (wash-basin) T 60 C (sink) For low pressure extractable outlets complying with this standard there are no acoustical requirements. Low pressure extractable outlets complying with this standard may also be used with inlet supply pressures in the range from 0,1 MPa to 0,2 MP

27、a (1,0 bar to 2,0 bar) on condition that acoustical performance is not a requirement of the installation. BS EN 16145:2012EN 16145:2012 (E) 7 Key 1 cold water 2 hot Water 3 mains supply pipe (supply pressures up to 1 MPa (10 bar) 4 water heater Figure 1 Supply system type 1 with a pressure range of

28、0,05 MPa to 1,0 MPa (0,5 bar to 10 bar) BS EN 16145:2012EN 16145:2012 (E) 8 Key 1 cold water storage cistern (cover omitted for clarity) 2 warning pipe 3 vent pipe 4 hot water cylinder 5 alternative cistern fed cold supply to sanitary appliances 6 to boiler 7 mains supply pipe (supply pressures up t

29、o 1 MPa (10 bar) Figure 2 Supply system type 2 with a pressure range of 0,01 MPa to 1,0 MPa (0,1 bar - 10 bar). A vented domestic hot water and cold water supply system incorporating gravity hot water, mains cold water and alternative gravity cold water supply to sanitary appliances BS EN 16145:2012

30、EN 16145:2012 (E) 9 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document

31、(including any amendments) applies. EN 248, Sanitary tapware General specification for electrodeposited coatings of Ni-Cr EN 1717, Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow EN 16146, Sanitary tapware Extr

32、actable shower hoses for sanitary tapware for supply systems type 1 and type 2 General technical specification EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) EN ISO 3822-1, Acoustics Laboratory tests on no

33、ise emission from appliances and equipment used in water supply installations Part 1: Method of measurement (ISO 3822-1) EN ISO 3822-4, Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 4: Mounting and operating conditions for special

34、appliances (ISO 3822-4) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 spray outlet device for culinary and ablutionary purposes which allows water to be emitted in the form of jets or water droplets 3.2 spray plate device with orifices thro

35、ugh which water passes and forms a spray of water with separate, definable jets or water droplets Note 1 to entry: A spray forming mechanism is a device which generates a spray by other means. 3.3 spray mode selector device providing the possibility of selecting different spray modes Note 1 to entry

36、: Later described as mode (a), (b), (c). 4 Classification Extractable outlets are moveable hand held outlets which are connected to the sanitary tapware via a hose, complying with EN 16146. They can be mounted directly on the tapware or designed as a side spray located on an appropriate support. BS

37、EN 16145:2012EN 16145:2012 (E) 10 5 Designation Extractable outlets covered by this standard are designated by: their connecting thread dimension; their flow rate class (see Table 1); their acoustic group (where applicable); reference to this standard: EN 16145. EXAMPLE Extractable outlet G flow rat

38、e class E, EN 16145. 6 Marking Extractable outlets complying with this standard shall be marked permanently and legibly with the manufacturers mark or the suppliers mark. The acoustic group (where applicable) and the highest flow rate class shall appear on the product but it need not be permanent. E

39、xtractable outlets with special connection (see 12.3) delivered together with the tapware need not be marked individually. 7 Materials 7.1 Chemical and hygienic requirements All materials coming into contact with water intended for human consumption shall present no risk to health. They shall not ca

40、use any change of the drinking water in terms of quality, appearance, smell or taste. 7.2 Exposed surface condition and quality of coating Visible chromium plated surfaces and Ni-Cr coatings shall comply with the requirements of EN 248. 8 Dimensional Characteristics 8.1 General The design and constr

41、uction of components without defined dimensions permits various design solutions to be adopted by the manufacturer. Permitted deviations from the defined dimensions are given in 8.3. 8.2 Connecting Dimensions The connecting dimensions of extractable outlets are specified in Table 2. BS EN 16145:2012

42、EN 16145:2012 (E) 11 Figure 3 Extractable outlet Table 2 Connecting dimensions Dimension Values Comments A G 1 / 2 B EN ISO 228-1 B 7,5 mm B 9,5 mm 8.3 Special Cases For extractable outlets intended for special applications e.g., when interchangeability is not a requirement, the following incorporat

43、e dimensional deviations are provided: connection to the tapware is guaranteed; threaded connections are in compliance with ISO standards; all other requirements of this standard are satisfied; the manufacturers literature, including the installation instructions supplied with the extractable outlet

44、 indicates clearly that the extractable outlet is a special case. 9 Leaktightness Characteristics 9.1 Leaktightness of the inlet connection and the spray plate 9.1.1 General The tests described are type test (laboratory test) and not quality control tests carried out during manufacture. BS EN 16145:

45、2012EN 16145:2012 (E) 12 9.1.2 Test Method 9.1.2.1 Principle The test is based on the principle of checking the leaktightness of the extractable outlet with positive internal water pressure. 9.1.2.2 Apparatus for leaktightness (this apparatus is also used for thermal shock tests; refer to 10.4) The

46、test circuit is detailed in Figure 4. Key 8 supply circuit: 1) means for supplying and maintaining hot water temperature and pressure for the duration of the test 2) means for supplying and maintaining cold water temperature and pressure for the duration of the test 3) means for alternating from hot

47、 to cold water and vice versa 4) means for measuring pressure with an accuracy of 1 % 5) means for measuring temperature with an accuracy of 1 C 9 test circuit: 6) connection 7) test sample Figure 4 Test circuit for testing leaktightness and thermal shock For the leaktightness test, cold water shall

48、 be used. 9.1.2.3 Procedure Connect the extractable outlet as supplied to the test circuit. With water flowing at a temperature 30 C, apply the appropriate test pressure specified in Table 3 and maintain for (300 10) s. In the case of multifunction extractable outlets, the test shall be carried out for each function. Table 3 Pressure conditions for leaktightness test Extractable outlet for installation Type 1 (0,5 0,02) MPa (5,0 0,2) bar) Extractable outlet for installation Type 2 (0,2 0,02) MPa (2,0 0,2) bar) 9.1.2.4 Requirements For the duration of the test there shall be no leakage betw